21.120.30 键和键槽、花键 标准查询与下载

CSN 01 4950-1962 渐开线花键

Involute splines

BS 46-1:1958 键和键槽及锥形销.键和键槽规范

Materials, nominal sizes, tolerances; for parallel keys, taper keys, gib-head keys rectangular and square, and Woodruff keys. Nominal sizes, dimensions; for tangential keys, tapered-shaft-end keys, marine tailshaft keys. Details of all keyways. Preferred lengths of the plain and gib-head keys. Whitney, British and American Woodruff key numbers compared.

Keys and keyways and taper pins - Specification - Keys and keyways

GOST 1139-1958 互换性的基本规范 直边花键接合 尺寸规格和公差

Basic norms of interchangeability. Straight-sided splines. Dimensions and tolerances

BS 2059/2:1957 观察记录表.直边花键.底部配件.深底

Extracted from BS 2059:1953.

Summary sheet: straight sided splines - Bottom fitting - Deep

BS 2059/1:1957 观察记录表.直边花键.底部配件.浅底

Extracted from BS 2059:1953.

Summary sheet: straight sided splines - Bottom fitting - Shallow

BS 2059/3:1957 观察记录表.直边花键.内部和外部

Extracted from BS 2059:1953.

Summary sheet: straight sided serrations - Internal and external

DIN 6885-3:1956 无锥体作用的驱动式紧固件.浅插入型直销键.尺寸和用途

Drive Type Fastenings without Taper Action; Parallel Keys, Shallow Pattern, Dimensions and Application

BS 2059:1953 直边花键与锯齿形花键规范

Dimensions of internal and external splines and of Full Form $7Igo$7R gauges and $7Inot go$7R feature gauges. Dimensions for straight-sided 90 serrations, line size $9H in to 6 in, serration $9D in to 6 in. Tables for shallow and deep splines, and for coarse serrations only. Three grades of fit.

Specification for straight-sided splines and serrations

GOST 6033-1951 互换性基本规范 角度为30°的渐开线齿花键联接 尺寸、公差及测量值

Basic norms of interchangeability involute splines

CNS 163-1947 销子概览

Keys in General

CNS 176-1947 销子槽检验标准

Testing Standard for Key Seat

AS B212:1968 直边花键

Relates to splines produced in holes or on shafts of nominal size from ? to 6 in., for 4, 6, 10 and 16 splines of narrow depth and 6 and 10 splines of deep depth. Dimensions and gauging data are tabulated for bottom fitting (top clearance) and top fittin

Straight sided splines

AS B265:1968 渐开线锯齿

Part I provides design data and other details of involute serrations of 45° pressure angle 10/20, 16/32 and 24/48 pitches for the full range 60 to 100 serrations, and 32/64, 40/80, 48/96, 64/128, 80/160 and 128/256 pitches for limited range. Limiting dimensions are tabulated and manufacturing errors and their effect on fit between mating serrated elements are discussed. Part II gives the methods of gauging and inspection, and the design details for gauges.

Involute serrations

AS B213:1966 渐开线花键

Specifies dimensions of involute splined shafts and holes with a 30° pressure angle. Basic formulas for calculating dimensions and tolerances are included, with guidance on obtaining the fit desired. Terms used are defined. The Standard also describes methods of gauging and inspecting splines, with methods of obtaining dimensions and tolerances for gauges. Inspection of splines using pins is covered and tables of measurements over and between pins are included.

Involute splines