21.160 弹簧 标准查询与下载
共找到 479 条与 弹簧 相关的标准，共 32 页
Springs — Shot peening — Part 1: General procedures
- ICS
- 21.160
- CCS
- 发布
- 2023-09
- 实施
本文件规定了汽车悬架用螺旋弹簧的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输及贮存。
Spiral springs for automotive suspension
- ICS
- 21.160
- CCS
- C348
- 发布
- 2023-07-14
- 实施
- 2023-08-01
1 Scope This document specifies the measurement and test methods for general characteristics of cold formed helical extension springs made from round wire, excluding dynamic testing.
Springs. Measurement and test parameters - Cold formed cylindrical helical extension springs
- ICS
- 21.160
- CCS
- 发布
- 2023-06-30
- 实施
- 2023-06-30
Springs — Shot peening — Part 1: General procedures
- ICS
- 21.160
- CCS
- 发布
- 2023-06
- 实施
BS ISO 22705-3. Springs. Measurement and test parameters - Part 3. Cold formed cylindrical helical torsion springs
- ICS
- 21.160
- CCS
- 发布
- 2023-05-10
- 实施
- 2023-05-10
This document specifies the measurement and test methods for the general characteristics of cold formed helical compression springs made from round wire, excluding dynamic testing.
Springs — Measurement and test parameters — Part 1: Cold formed cylindrical helical compression springs
- ICS
- 21.160
- CCS
- 发布
- 2023-05-03
- 实施
本文件规定了电梯闭门器用拉簧的术语和定义、结构型式、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本文件适用于电梯闭门器用拉簧（以下简称“拉簧”）的生产和检验。
Extension spring for elevator door closer
- ICS
- 21.160
- CCS
- C348
- 发布
- 2023-03-22
- 实施
- 2023-04-10
This document specifies the measurement and test methods for general characteristics of cold formed helical extension springs made from round wire, excluding dynamic testing.
Springs — Measurement and test parameters — Part 2: Cold formed cylindrical helical extension springs
- ICS
- 21.160
- CCS
- 发布
- 2023-02-07
- 实施
- 2023-02
Helical compression and extension springs — Requirements for design
- ICS
- 21.160
- CCS
- 发布
- 2022-12-05
- 实施
本文件规定了汽车底盘用横向稳定杆（以下简称稳定杆）的组成及符号，基本要求、技术要求、检验方法、检验规则、标志、包装、运输、贮存以及质量承诺。 本文件适用于汽车底盘用横向稳定杆，包括实心和空心两种截面类型的稳定杆。
Vehicle chassis stabilizer bar
- ICS
- 21.160
- CCS
- C348
- 发布
- 2022-06-22
- 实施
- 2022-06-30
This document specifies two different grades of disc springs. Grade A defines basic requirements of disc springs for static applications with low and moderate performance. Springs manufactured according to Grade A are not used for dynamic applications. Grade B defines requirements on disc springs especially used for dynamic applications and high performance static applications. Disc springs according to Grade B ensure a better quality by higher demands on manufacturing processes and tolerance requirements. Grade B includes graphs showing the guaranteed fatigue life such as a function of stress.
Disc springs — Part 2: Technical specifications
- ICS
- 21.160
- CCS
- 发布
- 2022-05-12
- 实施
ISO 18137:2015 specifies the technical specifications for leaf springs. ISO 18137:2015 is applicable to leaf springs for road vehicle (hereinafter simply "springs"). The leaf springs for other vehicle may refer to this International Standard.
Leaf springs — Technical specifications
- ICS
- 21.160
- CCS
- 发布
- 2022-05-12
- 实施
1.1 This specification covers cold-drawn cobalt alloy spring wire intended especially for the manufacture of springs. 1.1.1 This specification requires capability properties after age hardening test samples of the cold worked spring wire to ensure final mechanical properties are satisfied. The spring is typically age hardened after fabrication to increase its strength. However, mechanical properties cannot be obtained from finished springs. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 Unless the order specifies an “M” designation, the material shall be furnished to inch-pound units. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Specification for Cobalt Alloy Spring Wire
- ICS
- 21.160
- CCS
- 发布
- 2022-04-01
- 实施
Leaf springs -- Part 4: Specification of products
- ICS
- 21.160
- CCS
- J26
- 发布
- 2021-11-22
- 实施
本文件规定了数控非打结弹簧生产线的术语和定义、基本参数、基本要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存、质量承诺。 本文件适用于加工床垫、沙发、座垫中的非打结弹簧，并用串簧条将单个弹簧组装成弹性体的数控生产线（以下简称“生产线”）。
Digital-controlled non-knotted spring production line
- ICS
- 21.160
- CCS
- C348
- 发布
- 2021-08-08
- 实施
- 2021-08-12
本文件规定了数控袋装卷簧机的术语和定义、基本参数、基本要求、技术要求、试验方法、检验规则、标志、 包装、运输和贮存、质量承诺。 本文件适用于把连续卷制成形的圆柱螺旋压缩弹簧、中凸形螺旋压缩弹簧或异形螺旋压缩弹簧装入封闭型袋中的数控卷簧装袋机（以下简称“卷簧装袋机”）。
Digital-controlled pocket spring machine
- ICS
- 21.160
- CCS
- C346
- 发布
- 2021-08-08
- 实施
- 2021-08-12
Springs — Measurement and test parameters — Part 1: Cold formed cylindrical helical compression springs
- ICS
- 21.160
- CCS
- 发布
- 2021-07-15
- 实施
- 2021-07-15
ISO 19690-1:2017 specifies design criteria and features of disc springs, whether as single disc springs or as stacks of disc springs. It includes the definition of relevant concepts, as well as design formulae, and covers the fatigue life of such springs.
Disc springs — Part 1: Calculation
- ICS
- 21.160
- CCS
- 发布
- 2021-07-01
- 实施
Springs – Measurement and test parameters – Part 1: Cold formed cylindrical helical compression springs
- ICS
- 21.160
- CCS
- 发布
- 2021-03-31
- 实施
- 2021-03-31
本文件规定了电梯曳引机制动器用压缩弹簧的术语和定义、弹簧结构形式、基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存及质量承诺等要求。 本文件适用于电梯曳引机制动器用冷卷圆柱螺旋压缩弹簧（以下简称“弹簧”）。 本文件不适用于特殊要求的弹簧。
Compressions spring for elevator traction machine brake
- ICS
- 21.160
- CCS
- C348
- 发布
- 2021-02-25
- 实施
- 2021-04-02
