21.220.10 带传动及其零件 标准查询与下载

GSO ISO 11749:2014 皮带传动 汽车工业用多楔带 疲劳试验

This International Standard specifies a dynamic test method for the quality control of V-ribbed belts (PK profile) which are used predominantly for accessory drive applications in the automotive industry. The dimensional characteristics of the belts and of corresponding pulleys are the subject of ISO 9981.

Belt drive -- V-ribbed belts for the automotive industry -- Fatigue test

GSO ISO 5291:2014 输送带 用于 V 型带的槽形皮带轮 槽形截面 AJ、BJ、CJ 和 DJ（主动系统）

This International Standard specifies the principal characteristics of grooved pulleys (for groove sections AJ, BJ, CJ and DJ), intended to take joined classical V-belts for industrial power transmission drives. NOTE 1 The effective width of a groove is regarded as the basic dimension of standardization for grooves and for the corresponding joined V-belts considered as a whole. NOTE 2 The pitch line position can only be given approximately. The approximate pitch diameter of a pulley can be calculated by the following formula: dp = de − 2be

Belt drives -- Grooved pulleys for joined classical V-belts -- Groove sections AJ, BJ, CJ and DJ (effective system)

GSO ISO 5292:2014 输送带 V 型带和多楔带 运转率的计算

This International Standard specifies generally ac- ceptable formulae for power ratings, together with appropriate correction terms and factors used in the design of industrial V-belt and V-ribbed belt drives with two pulleys. The formulae are suitable for use with cross-sections covered in existing International Standards as well as for cross-sections which are in the process of being studied for future International Standards.

Belt drives -- V-belts and V-ribbed belts -- Calculation of power ratings

GSO ISO 5294:2014 同步带传动 皮带轮

This International Standard specifies the principal characteristics of synchronous pulleys for use in synchronous endless belt drives for mechanical power transmission and where positive indexing or synchronization is required. NOTE These drives have been known under various names in the past, for example: timing belt drives, positive belt drives, gear belt drives. The principal characteristics include: a) tooth dimensions and tolerances; b) pulley dimensions and tolerances; c) quality specification. As far as dimensions are concerned, the pulleys specified in this International Standard are used interchangeably with the belts specified in ISO 5296.

Synchronous belt drives -- Pulleys

GSO ISO 9982:2014 皮带传动 工业应用的滑轮和多楔带 PH、PJ、PK、PL 和 PM 型材：尺寸

This International Standard specifies the principal dimensional characteristics of V-ribbed pulley groove profiles, together with the corresponding endless V-ribbed belts, of PH, PJ, PK, PL and PM profiles which are used for general industrial applications. The PK belt was originally established for automotive accessory drive applications and ISO 9981 deals specifically with that particular field.

Belt drives -- Pulleys and V-ribbed belts for industrial applications -- PH, PJ, PK, PL and PM profiles: dimensions

GSO ISO 5295:2014 同步带 计算运转率和传动中心距

This International Standard establishes formulae for the calculation of power rating and centre distance of standard .synchronous belts on two pulley drives. The numerical values of certain parameters used in the calculations depend upon the pitch and the construction of the belt and shall be specified by the belt manufacturer.

Synchronous belts -- Calculation of power rating and drive centre distance

ISO 13050:2014 同步带传动带. 公制螺距曲线系统G, H, R和S皮带和滑轮

This International Standard specifies the principal characteristics of metric pitch curvilinear synchronous endless belts and pulleys in G, H, R, and S profile systems for use in synchronous belt drives (also known in the past as timing belt drives, positive belt drives, gear belt drives) for mechanical power transmission and where positive indexing or synchronization might be required. The principal belt and pulley characteristics include the following: a) nominal belt tooth dimensions; c) belt length and width dimensions and tolerances; e) pulley groove dimensions and tolerances; b) belt tooth pitch spacing; d) belt length measurement specifications; f) pulley diameter and width dimensions and tolerances; g) pulley quality specification.

Synchronous belt drives - Metric pitch, curvilinear profile systems G, H, R and S, belts and pulleys

BS ISO 13050:2014 同步带传动带. 公制螺距曲线系统G, H, R和S皮带和滑轮

Synchronous belt drives. Metric pitch, curvilinear profile systems G, H, R and S, belts and pulleys

JB/T 7512.1-2014 圆弧齿同步带传动  第1部分:带

JB/T 7512的本部分规定了圆弧齿同步带传动中带的型号及标记、尺寸和带长测量方法。本部分适用于一般传动用圆弧齿同步带传动。

Circle-arc toothed synchronous belt drives.Part 1: Belts

JB/T 7512.3-2014 圆弧齿同步带传动  第3部分:设计方法

JB/T 7512的本部分规定了圆弧齿同步带传动设计方法中的术语、定义和代号、原始设计资料及设计步骤。本部分适用于一般传动用圆弧齿同步带传动设计。

Circle-arc toothed synchronous belt drives.Part 3: Design method

JB/T 7512.2-2014 圆弧齿同步带传动  第2部分:带轮

JB/T 7512的本部分规定了圆弧齿同步带传动中带轮的型号及标记、轮齿尺寸、带轮尺寸和带轮几何公差。本部分适用于一般传动用圆弧齿同步带传动。

Circle-arc toothed synchronous belt drives.Part 2: Pulleys

NF E24-202*NF ISO 1813:2014 皮带传动. 多楔带, 联组V型带以及V型带, 包括宽节带和六角带. 抗静电带的导电性: 试验特性和试验方法

La présente Norme internationale spécifie la résistance électrique maximale des courroies sans fin antistatique, de type courroies striées, courroies trapézoïdales simples et jumelées y compris celles à section large et hexagonales, ainsi que les méthodes de contrôle en production correspondantes et les méthodes de mesurage individuelle en laboratoire.L'application de la présente Norme internationale est limitée aux courroies neuves destinées à être utilisées en atmosphère explosive ou dans des situations où existe un risque d'incendie. L'essai permet de s'assurer que la courroie est suffisamment conductrice pour dissiper les charges d'électricité susceptib

Belt drives - V-ribbed belts, joined V-belts and V-belts including wide section belts and hexagonal belts - Electrical conductivity of antistatic belts : characteristics and methods of test

KS C IEC 60130-7-2014 频率低于3 MHz(Mc/s)的连接器 第7部分：带卡口或推拉耦合的圆形多极连接器

Connectors for frequencies below 3 MHz(Mc/s)－Part 7：Circular multipole connectors with bayonet or push-pull coupling

KS C IEC 60130-7:2014 频率低于3MHz（Mc/s）的连接器 第7部分：卡口连接或推拉连接的多极圆形连接器

Connectors for frequencies below 3 MHz(Mc/s)－Part 7：Circular multipole connectors with bayonet or push-pull coupling

BS ISO 1813:2014 皮带传动. 多楔带, 联组V型带以及V型带, 包括宽节带和六角带. 抗静电带的导电性: 试验特性和试验方法

Belt drives. V-ribbed belts, joined V-belts and V-belts including wide section belts and hexagonal belts. Electrical conductivity of antistatic belts: Characteristics and methods of test

BS ISO 11749:2014 皮带传动. 汽车工业用多楔带. 疲劳试验

Belt drive. V-ribbed belts for the automotive industry. Fatigue test

ISO 1813:2014 皮带传动.包括宽截面带及六角带的多楔带、有接头三角皮带、三角皮带.抗静电带的导电性:特性和试验方法

Belt drives - V-ribbed belts, joined V-belts and V-belts including wide section belts and hexagonal belts - Electrical conductivity of antistatic belts: Characteristics and methods of test

BS ISO 17396:2014 同步带传动带. 公制螺距, 梯形剖面系统T和AT, 皮带和滑轮

Synchronous belt drives. Metric pitch, trapezoidal profile systems T and AT, belts and pulleys

ISO 17396:2014 同步带传动. 公制节距, T和AT梯形剖面系统, 带及带轮

This International Standard specifies the principal characteristics of synchronous endless and open belts and pulleys of the profile systems T and AT for use in synchronous belt drives1) for mechanical power transmission and where positive indexing or synchronization can be required. The principal belt and pulley characteristics include a) nominal belt tooth dimensions, c) belt length and width dimensions, e) pulley groove dimensions and tolerances, b) belt tooth pitch spacing, d) belt length measurement specifications, f) pulley diameter and width dimensions and tolerances, and g) pulley quality specification. The belts of the profile systems T and AT are made of polyurethane with high-tension fine steel cord tension members in most cases. As far as certain forces are given in this International Standard, these values are only valid for this kinds of belt. For polyurethane belts with different tensile cords, i.e. aramid or rubber belts reinforced with glass fibre, the values can be different. It is intended that the user and the manufacturer agree about suitable values. Open belts made of thermoplastic polyurethane can be spliced to work as endless belts in conveyor applications. In this case, the tolerances are not valid for the splicing area of the endless spliced belt.

Synchronous belt drives - Metric pitch, trapezoidal profile systems T and AT, belts and pulleys

GSO ISO 9563:2013 输送带无限远非静止同步输送带的电气连接特点及隐蔽方法

This International Standard specifies the maximum electrical resistance of antistatic endless synchronous belts and a corresponding laboratory method of measurement. The test is intended to ensure that the belt is sufficiently conductive to dissipate charges of electricity which may form in it in service. The application of this International Standard is limited to cases of dispute about new belts intended for use in an explosive atmosphere, in situations where there is a fire risk, or wherever a static discharge cannot be permitted. The decision is left to national standards or to agreement between interested parties as to whether the test should be carried out on each belt in a batch or on only a percentage of the batch.

Belt drives -- Electrical conductivity of antistatic endless synchronous belts -- Characteristics and test method