21.220.10 带传动及其零件 标准查询与下载

BS ISO 13050:1999 曲线齿状同步皮带驱动系统

Specifies the principle characteristics of endless belt and pulley systems used for mechanical power transmission where positive indexing is required.

Curvilinear toothed synchronous belt drive systems

ISO 13050:1999 曲线齿状同步带传动系统

This International Standard specifies the principal characteristics of synchronous endless belts and pulleys for use in synchronous belt drives for mechanical power transmission and where positive indexing or synchronization may be required. The principal belt and pulley characteristics include: a) nominal belt tooth dimensions; b) belt tooth pitch spacing; c) belt length and width dimensions; d) belt length-measurement specifications; e) pulley groove dimensions and tolerances; f) pulley diameter and width dimensions and tolerances; g) pulley quality specification. note: 1) Synchronous belt drives have been known by various titles in the past: for example, timing belt drives, positive belt drives, gear belt drives.

Curvilinear toothed synchronous belt drive systems

BS ISO 155:1999 带传动.皮带轮.中心调整极限值

Applicable to crown pulleys for flat belts, grooved pulleys for V- and V-ribbed belts and toothed pulleys for synchronous belts.

Belt drives - Pulleys - Limiting values for adjustment of centres

KS B 1420-1998(2003) 同步带传动 - 滑轮

SYNCHRONOUS BELT DRIVES-PULLEYS

BS ISO 9982:1998 皮带传动.工业用皮带轮和V型加肋皮带.PH、PJ、PK、PL和PM型面.尺寸

This International Standard specifies the principal dimensional characteristics of V-ribbed pulley groove profiles, together with the corresponding endless V-ribbed belts, of PH, PJ, PK, PL and PM profiles which are used for general industrial applications. The PK belt was originally established for automotive accessory drive applications and ISO 9981 deals specifically with that particular field.

Belt drives - Pulleys and V-ribbed belts for industrial applications - PH, PJ, PK, PL and PM profiles - Dimensions

DIN 2215:1998 环形V-型皮带.经典V-型皮带.尺寸

This document specifies the belt-lengths Y, Z, A, B, C, D and E and their tolerances, the maximum centre distance variations, the minimum diameters of the pulleys, the test methods and the designations for classical V-belts.

Endless V-belts - Classical V-belts - Dimensions

ISO 254:1998 带传动 带轮 质量、表面光洁度和平衡

This International Standard specifies the characteristics of quality which are common to all transmission pulleys. It establishes specific quality levels for the finish and balance of transmission pulleys and test pulleys. This International Standard is applicable to transmission pulleys for V-belts, V-ribbed belts, flat or synchronous belts; it does not apply to those pulleys for variable speed drives that have one or more moving flanges. The other characteristics of transmission pulleys may be found in the relevant International Standards.

Belt drives - Pulleys - Quality, finish and balance

ISO 155:1998 带传动 带轮 中心调整极限值

This International Standard specifies the limiting values for the adjustment of centres of two transmission pulleys. It is applicable to — crowned pulleys for flat belts; — grooved pulleys for V-belts, either single, multiple or joined; — grooved pulleys for V-ribbed belts; — toothed pulleys for synchronous belts. NOTE — All dimensions are expressed in millimetres.

Belt drives - Pulleys - Limiting values for adjustment of centres

ISO 1813:1998 带传动 多楔带、有接头V带、宽截面带及六角带 抗静电带的电导率:特性和试验方法

This International Standard specifies the maximum electrical resistance of antistatic endless V-ribbed belts, joined V-belts, and single V-belts including wide section belts and hexagonal belts, as well as corresponding production control and individual proof methods of measurements. The application of this International Standard is limited to new belts intended to be used in an explosive atmosphere or in situations where there is a fire risk. The test is intended to ensure that the belt is sufficiently conductive to dissipate charges of electricity which may form on it in service. In the case of a production control test, the decision is left to national standards or agreement between interested parties as to whether the test shall be carried out on each belt in a batch or on only a percentage of belts in a batch. NOTE — For each proof test, the belt manufacturer should determine which type of electrode and conductive coating material must be used.

Belt drives - V-ribbed belts, joined V-belts and V-belts including wide section belts and hexagonal belts - Electrical conductivity of antistatic belts: Characteristics and methods of test

ISO 9982:1998 带传动 工业用带轮和多楔带 PH、PJ、PK、PL和PM型尺寸

This International Standard specifies the principal dimensional characteristics of V-ribbed pulley groove profiles, together with the corresponding endless V-ribbed belts, of PH, PJ, PK, PL and PM profiles which are used for general industrial applications. The PK belt was originally established for automotive accessory drive applications and ISO 9981 deals specifically with that particular field.

Belt drives - Pulleys and V-ribbed belts for industrial applications - PH, PJ, PK, PL and PM profiles: Dimensions

ASME B29.300-1998 农用可拆卸和斜栓节链附件和供片轮

On August 26,1998, the B29 Standard committee agreed via letter ballot to consolidate and revise the following three chain standards: ASME B29.6, Steel Detachable Link Chains, Attachments, and Sprockets; ASME B29.19, Agricultural Roller Chains, Attachments, and Sprockets; and ASME B29.25, Open Barrel Steel Pintle-Type Conveyor Chains, Attachments, and Sprockets. The new Standard was designated ASME B29.300, and entitled Agricultural, Detachable, and Pintle Chains, Attachments, and Sprockets. The 1998 revisions of B29.6, B29.19, and B29.25 have been designed to integrate the agricultural type chains found in each of these three Standards. B29.6 - Steel Detachable Link Chains, Attachments, and Sprockets This Standard establishes, in the main, only those dimensions that will provide for interchangeability of the chains in use without restricting the chain manufacturers in their overall design. The 1983 revision included the sprocket dimension controlling the surfaces that must properly engage or clear the chain. The 1994 edition updated the Standard to the current ANSI standards format and symbols covering chains. Number 45 and No. 67 were deleted from the Standard since they are no longer manufactured. The definition of Minimum Ultimate Tensile Strength (M.U.T.S.) was also updated. In this edition, the symbols and sprocket information sections were revised to provide consistency throughout the consolidated B29.300 Standard. B29.19 - Agricultural Roller Chains, Attachments, and Sprockets The Standard establishes essentially only those dimensions that will provide for interchangeability of the chains in use without restricting the chain manufacturers in their overall designs. The B29 Committee agrees that the CA550 and CA620 chains may be used on No. 55 and No. 62 detachable chain sprockets, respectively; however, the sprocket data included in this Standard is for sprockets designed specifically for CA550 and CA620 chains. The difference in sprocket design is necessary because of the difference in roller diameters. The 1993 revision included updating to the current ANSI standards format and symbols covering chains and sprockets. Minimum Ultimate Tensile Strength (M.U.T.S.) was redefined. The 1996 revision changed the name of the Standard from A and CA550 and 620 Roller Chains, Attachments, and Sprockets to Agricultural Roller Chains, Attachments, and Sprockets. Also, two new chains for both drive series (A555 and A557) and conveyor series (CA555 and CA557), as well as several associated attachments, were added to the Standard. In this edition, the sprocket tooth form was modified to be identical with the form used in the other two chains. B29.25 - Open Barrel Steel Pintle-Type Conveyor Chains, Attachments, and Sprockets The open barrel steel pintle chain was originally developed in 1962 for the agricultural implement industry. The original sizes were developed to run on the same sprockets as their detachable chain counterparts of ANSI B29.6. In later years, sizes were developed to accommodate industrial applications as well. The steel pintle chain is primarily used as a conveyor chain and, in limited use, as a power transmission chain. Typical conveyor speeds are under 300 ft/min. Consult manufacturers for details. The 1994 revision incorporated a restatement of the definition of Minimum Ultimate Tensile Strength (M.U.T.S.), and an addition of footnotes in Tables 3 and 4 regarding hole sizes in certain attachments. In this edition, Tables 1 and 2 were combined for simplicity, and the sprocket tooth form was modified to be identical with the form used for the other two chains.

Agricultural, Detachable, and Pintle Chains, Attachments, and Sprockets Incorporating ASME B29.6, B29.19, and B29.25; Addenda A:2004 [Superseded: ASME B29.6M, ASME B29.6M] [Replaced: ASME B29.25M, ASME B29.25M]

NF E24-405:1997 皮带传动.V型加筋皮带.工业用PJ和PH型材的动力试验方法(家用)

Belt drives. V ribbed belts. Dynamic test methods for PJ and PH profiles for industrial applications (specific to domestic appliances).

QB/T 2291-1997 机用皮带扣

本标准规定了机用皮带扣的产品分类、技术要求、试验方法、检验规则、标志、包装、运辐和贮存。 本标准适用于15号~75号平行传动带及翰送带配合使用的机用皮带扣。

Machine belt fastener

NF R15-513:1996 同步皮带传动装置.汽车皮带和皮带轮.疲劳试验

Synchronous belt drives. Automotive belts and pulleys. Fatigue test.

GOST 1284.3-1996 标准截面的传动三角皮带.传输功率

Настоящий стандарт распространяется на бесконечные резинотканевые приводные клиновые ремни нормальных сечений по ГОСТ 1284.1 и ГОСТ 1284.2

V-belts of standart cross-sections. Transmitted powers

SR ISO 254:1996 皮带传动．滑轮．质量，面漆和平衡

Belt drives - Pulleys - Quality, finish and balance

NF E24-404:1995 皮带传动装置.V形加筋皮带.辊距、角度和绳索位置的测定

Belt drives. V-ribbed belts. Determination of measurement of pitch, angle and cord position.

ISO 11749:1995 带传动 汽车工业用多楔带 疲劳试验

Refers to a dynamic test method for the quality control of V-ribbed belts which are used predominantly in the automotive industry. The dimensional characteristics of the belts and of corresponding pulleys are the subject of ISO 9981.

Belt drive - V-ribbed belts for the automotive industry - Fatigue test

NF E24-403:1995 皮带传动装置.V-形加筋的皮带.直线密度的确定

Belt drives. V-ribbed belts. Determination of linear density.

ISO 4183:1995 带传动 标准的和窄V带 带轮(标准宽度系列)

Cancels and replaces the second edition (1989). Specifies the principal dimensions of grooved pulleys for classical V-belts and narrow V-belts specified in the terminology system based on datum width. It is important that narrow belts are not used with pulleys uniquely designed for classical belts, and, on the other hand, that multiple belt drives are not used with joined V-belts.

Belt drives - Classical and narrow V-belts - Grooved pulleys (system based on datum width)