21.220.10 带传动及其零件 标准查询与下载

JB/T 7700.2-2016 金属旋压带轮.第2部分:板材旋压多楔带轮

JB/T 7700的本部分规定了金属板材旋压多楔带轮(以下简称带轮)的型式和槽型尺寸、技术要求、试验方法、检验规则、标志、包装、运输和贮存。本部分适用于汽车、工程机械、农用机械、家电、特种设备等传动用多楔带轮。

Metal spinning pulleys.Part 2: Sheet spinning V-ribbed belts pulleys

BS ISO 19347:2015 同步带传动带. 梯形轮廓系统. 皮带和滑轮

Synchronous belt drives. Imperial pitch trapezoidal profile system. Belts and pulleys

ISO 19347:2015 同步带传动. 英制节距梯形剖面系统. 带及带轮

Synchronous belt drives - Imperial pitch trapezoidal profile system - Belts and pulleys

BS ISO 9563:2015 皮带传动装置. 抗静电,连续同步传动的皮带的电导率. 特性和试验方法

Belt drives. Electrical conductivity of antistatic endless synchronous belts. Characteristics and test method

GSO ISO 5288:2015 电机同步带 词汇

This International Standard specifies the terms and definitions related to the use of endless synchronous belt drives for mechanical power transmission and where positive indexing or synchronization is required.

Synchronous belt drives -- Vocabulary

GSO ISO 5290:2015 皮带传动 与窄互连三角带一起使用的沟槽皮带轮 沟槽类型 9N/J、15N/J、25N/J（主动系统）

This International Standard specifies the principal characteristics of grooved pulleys (for groove sections 9N/J, 15N/J and 25N/J) intended to take both single and joined narrow V-belts for industrial power transmission drives. Some background information on the series of effective diameters is given in annex A. NOTE The effective width of a groove is regarded as the basic dimension of standardization in the effective system for grooves and for the corresponding narrow V-belts considered as a whole.

Belt drives -- Grooved pulleys for joined narrow V-belts -- Groove sections 9N/J, 15N/J and 25N/J (effective system)

GSO ISO 4184:2015 电机皮带 传统和窄三角带 支撑系统的长度

This International Standard specifies, for classical and narrow V-belts of sections Y (for groove profile with datum width 5,3 mm), Ζ (for groove profile with datum width 8,5 mm), A (for groove profile with datum width 11 mm), В (for groove profile with datum width 14 mm), С (for groove profile with datum width 19 mm), D (for groove profile with datum width 27 mm), Ε (for groove profile with datum width 32 mm), SPZ (for groove profile with datum width 8,5 mm), SPA (for groove profile with datum width 11 mm), SPB (for groove profile with datum width 14 mm), SPC (for groove profile with datum width 19 mm): — the recommended datum lengths; — the tolerances for datum lengths; — the centre distance variations; — the conditions for measuring the datum length and the centre distance variation. The V-belts of sections Y, Z, А, В, C, D, Ε are called classical V-belts and those of sections SPZ, SPA, SPB and SPC are called narrow V-belts. It is important that narrow belts are not used with pulleys uniquely designed for classical belts.

Belt drives -- Classical and narrow V-belts -- Lengths in datum system

GSO ISO 1081:2015 皮带传动 V型皮带和多楔带以及相应的槽形皮带轮 词汇

This International Standard specifies the terms and definitions, in English and French, relating to aromatic natural raw materials. This International Standard defines terms relating to V-belt drives, V-belts, hexagonal belts, joined V-belts and the corresponding V-grooved pulleys, V-ribbed belt drives, V-ribbed belts and V-ribbed pulleys, as well as the corresponding symbols. The general definitions are valid irrespective of the system describing the pulleys. The dimensions of pulley grooves can be defined either on the basis of the datum width or on the basis of the effective width. As a result, two systems for the definition and description of the dimensions of pulleys and belts have been developed. The two systems are independent of each other.

Belt drives -- V-belts and V-ribbed belts, and corresponding grooved pulleys -- Vocabulary

GSO ISO 254:2015 皮带传动 滑轮 质量、光洁度和平衡

This International Standard specifies the characteristics of quality which are common to all transmission pulleys. It establishes specific quality levels for the finish and balance of transmission pulleys and test pulleys. This International Standard is applicable to transmission pulleys for V-belts, V-ribbed belts, flat or synchronous belts; it does not apply to those pulleys for variable speed drives that have one or more moving flanges. The other characteristics of transmission pulleys can be found in the relevant International Standards.

Belt drives -- Pulleys -- Quality, finish and balance

GSO ISO 4183:2015 皮带传动 传统和窄三角带 槽形皮带轮（基于继电器宽度的系统）

This International Standard specifies the principal dimensions of grooved pulleys for classical V-belts (sections Υ, Ζ, A, B, C, D and E) and narrow V-belts (sections SPZ, SPA, SPB and SPC) specified in the terminology system based on datum width. It is important that narrow belts are not used with pulleys uniquely designed for classical belts, and, on the other hand, that multiple belt drives are not used with joined V-belts.

Belt drives -- Classical and narrow V-belts -- Grooved pulleys (system based on datum width)

GSO ISO 5296:2015 同步带传动 节距代码为 MXL、XXL、XL、L、H、XH 和 XXH 的皮带 公制和英制尺寸

This International Standard specifies the principal characteristics of synchronous endless belts for use in synchronous belt drives for mechanical power transmission and where positive indexing or synchronization is required. NOTE Synchronous belt drives have been known by various titles, for example timing belt drives, positive belt drives, and gear belt drives. The principal characteristics include: a) nominal tooth dimensions; b) length and width dimensions; c) tolerances on these dimensions; d) length-measurement specifications. This International Standard is applicable to synchronous belt drives with pitch codes MXL, XXL, XL, L, H, XH and XXH, in both metric and inch dimensions.

Synchronous belt drives -- Belts with pitch codes MXL, XXL, XL, L, H, XH and XXH -- Metric and inch dimensions

GSO ISO 1604:2015 皮带传动 用于工业变速器的环形宽 V 型皮带和用于相应皮带轮的凹槽型材

This International Standard specifies the principal dimensions of endless wide V-belts for industrial speed-changers, and the groove profiles of corresponding fixed or variable diameter pulleys. It does not apply to speed-changer belts used either as parts of farm-machines (in particular harvesters), which are standardized in ISO 3410, or for the propulsion of self-propelled vehicles (motor-cycles, scooters, cars).

Belt drives -- Endless wide V-belts for industrial speed-changers and groove profiles for corresponding pulleys

ISO 9563:2015 带传动.抗静电同步带的电导率.特性及试验方法

This International Standard specifies the maximum and minimum electrical resistance of antistatic endless and open ended synchronous belts. This International Standard provides guidelines to allow testing of synchronous belts to prove their static conductive (dissipative) properties as well as a corresponding production control test method. The application of this International Standard is limited to new belts intended to be used in an explosive atmosphere or in situations where there is a fire risk. The test is intended to ensure that the belt is sufficiently conductive to dissipate charges of electricity which may form on it in service. In the case of a production control test, the decision is left to national standards or agreement between interested parties as to whether the test shall be carried out on each belt in a batch or on only a percentage of belts in a batch. For each proof test, the belt manufacturer shall determine which type of electrode and conductive coating material shall be used.

Belt drives - Electrical conductivity of antistatic endless synchronous belts - Characteristics and test method

JIS B 1857-1:2015 通用电力传输用曲线式锯齿形同步皮带驱动系统.第1部分:皮带

Curvilinear toothed synchronous belt drive systems for general power transmission -- Part 1: Belt

JIS B 1857-2:2015 通用电力传输用曲线式锯齿形同步皮带驱动系统.第2部分:皮带轮

Curvilinear toothed synchronous belt drive systems for general power transmission -- Part 2: Pulley

HG/T 4748-2014 传动带摩擦系数试验方法

本标准规定了轻型平型传动带和片基厚度不超过0.5 mm的聚酰胺片基平带(以下简称平带)及多楔带(PK型)的摩擦系数测试方法。 本标准适用于在规定条件下测定平带和多楔带(PK型)的摩擦系数。

Test method of friction factor for drive belts

GSO ISO 5291:2014 输送带 用于 V 型带的槽形皮带轮 槽形截面 AJ、BJ、CJ 和 DJ（主动系统）

This International Standard specifies the principal characteristics of grooved pulleys (for groove sections AJ, BJ, CJ and DJ), intended to take joined classical V-belts for industrial power transmission drives. NOTE 1 The effective width of a groove is regarded as the basic dimension of standardization for grooves and for the corresponding joined V-belts considered as a whole. NOTE 2 The pitch line position can only be given approximately. The approximate pitch diameter of a pulley can be calculated by the following formula: dp = de − 2be

Belt drives -- Grooved pulleys for joined classical V-belts -- Groove sections AJ, BJ, CJ and DJ (effective system)

GSO ISO 12046:2014 同步传动带 汽车带 物理性能的测定

This International Standard specifies test methods for determining the physical properties of synchronous belts used in driving engine parts, such as camshafts, fuel injection pumps, balancing shafts. These test methods are intended to provide a means of characterizing synchronous belt properties for belts which are evaluated and qualified by dynamic laboratory and field testing. NOTE The dimensional characteristics of these belts are the subject of ISO 9010.

Synchronous belt drives -- Automotive belts -- Determination of physical properties

GSO ISO 5295:2014 同步带 计算运转率和传动中心距

This International Standard establishes formulae for the calculation of power rating and centre distance of standard .synchronous belts on two pulley drives. The numerical values of certain parameters used in the calculations depend upon the pitch and the construction of the belt and shall be specified by the belt manufacturer.

Synchronous belts -- Calculation of power rating and drive centre distance

GSO ISO 5292:2014 输送带 V 型带和多楔带 运转率的计算

This International Standard specifies generally ac- ceptable formulae for power ratings, together with appropriate correction terms and factors used in the design of industrial V-belt and V-ribbed belt drives with two pulleys. The formulae are suitable for use with cross-sections covered in existing International Standards as well as for cross-sections which are in the process of being studied for future International Standards.

Belt drives -- V-belts and V-ribbed belts -- Calculation of power ratings