23.020.10 固定容器和罐 标准查询与下载

DVS 2205-2 Beiblatt 7-2010 由热塑性塑料制成的储罐和设备的计算 立式圆形常压储罐 截环锥底

Calculation of storage tanks and equipment made of thermoplastic plastics Vertical circular atmospheric storage tanks with truncated ring cone bottoms

DVS 2205-2 Beiblatt 8-2010 由热塑性塑料制成的储罐和设备的计算 立式圆形非加压储罐 环支撑锥底示例

Calculation of tanks and equipment made of thermoplastics Vertical circular non-pressurized tank ring support cone bottom example

BS 799-5:2010 燃油设备.碳钢储油罐.规范

This part of BS 799 specifies requirements for the construction and testing of static carbon steel tanks for the storage of liquid fuel of classes A2, C1, C2, D, E, F, G and H conforming to BS 2869:2006 and FAME (fatty acid methyl esters) conforming to BS EN 14213, for use in conjunction with oil burning equipment. The standard is applicable to tanks of the following types intended for use above ground, either externally or internally to a building: a) service tanks; b) primary storage tanks with a capacity of 90 L or more with a maximum height of 10 m. This standard is not applicable to tanks that are to be buried.

Oil burning equipment - Carbon steel oil storage tanks - Specification

DS/EN 13121-3+A1:2010 地上使用的 GRP 储罐和容器 第3部分：设计和工艺

This European Standard gives requirements for the design, fabrication, inspection, testing and verification of GRP tanks and vessels with or without Thermoplastics lining for storage or processing of fluids, factory made or site built, non pressurised or pressurised up to 10 bar, for use above ground.The terms vessels and tanks as used in this European Standard include branches up to the point of connection to pipe work or other equipment by bolting and supports, brackets or other attachments bonded directly to the shell. In addition to the definitive requirements, this European Standard also requires the items in Clause 5 to be fully documented.This Europe

GRP tanks and vessels for use above ground - Part 3: Design and workmanship

NF M88-557-3:2010 地上用玻璃纤维增强塑料(GPR)罐和容器.第3部分:设计和工艺

GRP tanks and vessels for use above ground - Part 3 : design and workmanship.

DVS 2205-2 Beiblatt 10-2010 由热塑性塑料制成的储罐和设备的计算 站立的圆形非加压储罐 平行支撑的倾斜底部示例

Calculations for tanks and equipment made of thermoplastics Example of a standing circular non-pressurized tank with a parallel supported sloping bottom

DVS 2205-2 Beiblatt 9-2010 由热塑性塑料制成的储罐和设备的计算 立式、圆形、常压储罐 平行支撑的斜底

Calculation of storage tanks and equipment made of thermoplastic plastics Vertical, round, parallel-supported inclined bottoms of atmospheric storage tanks

DVS 2205-2 Beiblatt 2-2010 由热塑性塑料制成的罐和设备的计算 立式、圆形、常压罐 收集装置

Calculation of tanks and equipment made of thermoplastics Vertical, round, atmospheric tank collection devices

DVS 2205-2-2010 由热塑性塑料制成的储罐和设备的计算 立式圆形常压储罐

Calculation of storage tanks and equipment made of thermoplastic plastic Vertical circular atmospheric storage tanks

DVS 2205-2 Beiblatt 3-2010 由热塑性塑料制成的罐和设备的计算 立式圆形常压罐 平屋顶

"Calculation of tanks and apparatus made of thermoplastics - Vertical round, non-pressurised tanks - Flat roofs"

DVS 2205-2 Beiblatt 6-2010 由热塑性塑料制成的储罐和设备的计算 立式圆形非加压储罐 外壳结构

Calculation of vertical circular non-pressurized tank shell structures for tanks and equipment made of thermoplastics

ANSI/AWWA D108-2010 贮水设备用铝制拱顶

This standard establishes minimum criteria for the design, fabrication, and erection of structurally supported aluminum dome roofs.

Aluminum Dome Roofs for Water Storage Facilities

ASTM D3299-10 纤维缠绕玻璃纤维强化热固性树脂防腐罐的标准规范

1.1 This specification covers cylindrical tanks fabricated by filament winding for above-ground vertical installation, to contain aggressive chemicals at atmospheric pressure as classified herein, and made of a commercial-grade polyester or vinylester resin. Included are requirements for materials, properties, design, construction, dimensions, tolerances, workmanship, and appearance. 1.2 This specification does not cover the design of vessels intended for pressure above atmospheric, vacuum conditions, except as classified herein, or vessels intended for use with liquids heated above their flash points. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. Note 18212;Special design consideration should be given to vessels subject to superimposed mechanical forces, such as earthquakes, wind load, or agitation, and to vessels subject to service temperature in excess of 180°F (82°C), and to vessels with unsupported bottoms. Note 28212;There is no similar or equivalent ISO standard. 1.4 The following safety hazards caveat pertains only to the test method portion, Section 11, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Filament-Wound Glass-Fiber-Reinforced Thermoset Resin Corrosion-Resistant Tanks

ANSI/ASTM D3299:2010 绕组丝玻璃纤维增强热固树脂耐腐蚀容器用规范

Specification for Filament-wound Glass-Fiber-Reinforced Thermoset Resin Corrosion-Resistant Tanks

ANSI/AWWA D107-2010 蓄水用升高的复合材料贮水池

This standard describes the design, construction, inspection, and testing of composite elevated tanks that utilize a welded steel tank for watertight containment and a single pedestal concrete support structure. Requirements for the steel tank, concrete support structure, foundation, and accessories are included. Site selection and procurement, tank sizing, post-commissioning inspection and maintenance, and the design, operation, and control of the water distribution system that connects to the composite elevated tank are beyond the scope of this standard.

Composite Elevated Tanks for Water Storage

NB/T 47003.1-2009 钢制焊接常压容器

本部分规定了钢制焊接常压容器的设计、制造、检验与验收的要求。 本部分的适用范围为： 圆筒形容器：设计压力大于-0.02MPa，小于0.1MPa，设计温度范围按钢材允许的使用温度确定； 矩形容器：设计压力为零，设计温度范围按钢材允许的使用温度确定。 本部分不适用于下列容器： 直接受火焰加热的容器； 受核辐射的容器； 盛装毒性为极度或高度危害介质的容器； 直接埋入地下的容器； 可升降气柜； 经常搬动的容器； 料仓； 几何容积大于1000m的立式圆筒形容器； 高度大于10m且长径比大于5的塔式容器。

Steel welded atmospheric pressure vessels

NB/T 47003.2-2009 固体料仓

NB/T 47003的本部分规定了固体料仓的设计、制造、检验与验收的要求。 本部分适用于容积大于15m，设计压力大于-500Pa小于0.1MPa，设计温度为仓壳材料允许使用温度的储存固体松散物料的钢制、铝制焊接立式圆筒形料仓。超出上述参数范围的料仓，也可参照本部分进行设计与制造。 本部分不适用于下列各类料仓： 直接埋入地下的料仓； 盛装毒性为极度或高度危害介质的料仓； 经常搬运的料斗； 容积小于或等于15m的料斗。

Silos for solid materials

NB/T 47001-2009 钢制液化石油气卧式储罐型式与基本参数

本标准规定了钢制液化石油气卧式储罐的型式与公称压力、公称容积、公称直径、筒体长度、筒体厚度、封头厚度、安装尺寸、管口尺寸及卧罐质量等基本参数。 本标准适用于储存液化石油气且无保温设施的卧罐。

Steel liquefied petroleum gas horizontal tanks type and data base

KS B 6971-2009 液化天然气储罐.风险评估

이 표준은 LNG 저장탱크에서 LNG 및 NG가 누출될 때 이로 인한 위험도를 정량적으로

Standard for risk assessment of LNG storage tanks

KS B 6971-2009(2019) 液化天然气储罐风险评价标准

Standard for risk assessment of LNG storage tanks