23.020.10 固定容器和罐 标准查询与下载

LST EN 13160-5-2005/AC-2007 泄漏检测系统 第5部分：储罐液位计泄漏检测系统

Leak detection systems - Part 5: Tank gauge leak detection systems

UL 1313 BULLETIN-2007 石油产品用非金属安全罐UL安全性标准.STP投票和评议提交截止日期:2007年5月21日

These requirements cover nonmetallic safety cans that have nominal capacities of 5 Imperial gallons or less and that are primarily intended to store and handle fuel oil, gasoline, kerosene. Nonmetallic safety cans that are intended to store and handle liquid fuels other than those specified above may be subjected to additional requirements not covered in the Standard. These requirements cover cans of two types, designated herein as Type I and Type II.

UL Standard for Safety Nonmetallic Safety Cans for Petroleum Products STP BALLOTS AND ALL COMMENTS DUE: MAY 21, 2007

ASTM F1657-96(2007) 紧急连接带不兼容连接器的吊杆的标准实施规程

Standard Practice for Emergency Joining of Booms with Incompatible Connectors

DIN 6600:2007 水存储用钢制容器.污水液体.合格评定

The standard describes a procedure for the proof of conformity of workshop fabricated steel tanks manufactured according to certain product standards by means of a certificate of conformity.

Steel tanks for the storage of water-polluting liquids - Declaration of conformity

DIN 6601:2007 钢容器材料的耐液体侵蚀特性(正性液体表)

The list of liquids shows the chemical name of those liquids which are intended to store in metallic tanks. Moreover the list contains instructions which have to be met by storage of these liquids.

Resistance of materials of steel tanks against liquids (positiv-list of liquids)

DS/EN 14620-4:2007 用于储存工作温度在 0°C 和 -165°C 之间的冷冻液化气体的现场建造的立式、圆柱形、平底钢罐的设计和制造 第4部分：绝缘组件

This European Standard specifies the requirements for materials, design and installation of the insulation of refrigerated liquefied gas (RLG) storage tanks.RLG storage tanks store liquefied gas with a low boiling point, i.e. below normal ambient temperature.The concept of storing such products in liquid form and in non-pressurized tanks therefore depends on the combination of latent heat of vaporization and thermal insulation.Consequently thermal insulation for RLG storage tanks is not an ancillary part of the containment system (as for most ambient atmospheric hydrocarbon tanks) but it is an essential component and the storage tank cannot operate without

Design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and -165 °C - Part 4: Insulation components

DS/EN 14620-5:2007 用于储存工作温度在 0°C 和 -165°C 之间的冷冻液化气体的现场建造立式圆柱形平底钢罐的设计和制造 第5部分：测试、干燥、吹扫和冷却

This European Standard specifies the requirements for testing, drying, purging and cool-down of the refrigerated liquefied gas storage tanks.This European Standards deals with the design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and -165 °C.

Design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and -165 °C - Part 5: Testing, drying, purging and cool-down

DS/EN 14620-3:2007 用于储存工作温度在 0°C 和 -165°C 之间的冷冻液化气体的现场建造的立式、圆柱形、平底钢罐的设计和制造 第3部分：混凝土构件

This European Standard specifies general requirements for materials, design and construction of the concrete components of the refrigerated liquefied gas storage tanks.This European Standard deals with the design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and -165 °C.

Design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and -165 °C - Part 3: Concrete components

DS/EN 14620-2:2007 用于储存工作温度在 0°C 和 -165°C 之间的冷冻液化气体的现场建造的立式、圆柱形、平底钢罐的设计和制造 第2部分：金属部件

This European Standard specifies general requirements for the materials, design, construction andinstallation of the metallic components of refrigerated liquefied gas storage tanks.This European Standard deals with the design and manufacture of site built, vertical, cylindrical, flatbottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperaturesbetween 0 °C and –165 °C.

Design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and -165 °C - Part 2: Metallic components

DS/EN 14620-1:2007 用于储存工作温度在 0°C 和 -165°C 之间的冷冻液化气体的现场建造的立式、圆柱形、平底钢罐的设计和制造 第1部分：总则

This European Standard is a specification for vertical, cylindrical tanks, built on site, above groundand of which the primary liquid container is made of steel. The secondary container, if applicable, maybe of steel or of concrete or a combination of both. An inner tank made only of pre-stressed concreteis excluded from the scope of this European Standard.This European Standard specifies principles and application rules for the structural design of the“containment” during construction, testing, commissioning, operation (accidental included), anddecommissioning. It does not address the requirements for ancillary equipment such as pumps,pumpwells, valves, pi

Design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and -165 °C - Part 1: General

DB42/T 420-2007 汽车加油站用埋地钢制油罐安全技术条件

Safety specification for steel storage oil tank body underground of filling station

UL 1746-2007 钢制地下储罐用外部防腐蚀系统

These requirements cover preengineered corrosion protection systems. Part i covers factory-installed galvanic-type cathodic protection. Part ii covers factory assembled composite systems. Part iii covers factory assembled jacket systems. Part iv covers factory assembled coated systems. These corrosion protection systems are intended to be completely installed at the factory on carbon steel underground storage tanks. Part ii of this standard covers fiberglass reinforced plastic (FRP), materials only. Part iii of this standard covers FRP, polyurethane, polyurea and high density polyethylene (HDPE) materials only. Part iv covers polyurethane materials only. These corrosion protection systems are intended to be installed, operated and maintained in accordance with the manufacturer's instructions.

UL Standard for Safety External Corrosion Protection Systems for Steel Underground Storage Tanks Third Edition

KS B 6225-2006 焊接钢石油贮存罐

이 규격은 강제의 전체 용접 직립 원통형 저장 탱크로서 고정 지붕이나 부상 지붕 또는 고정

Welded steel tanks for oil storage

KS B 6283-2006 液体储罐的耐风压及抗震设计要求

이 규격은 액체저장탱크에 작용하는 풍압하중의 설계, 지진하중의 설계 및 앵커의 설계요건에

Design requirements for wind load and seismic load of oil storage tanks

BS EN 14620-1:2006 工作温度0℃～-165℃液态气体冷冻储存用垂直圆柱平底钢罐现场制造的设计和生产.总则

This European Standard is a specification for vertical, cylindrical tanks, built on site, above ground and of which the primary liquid container is made of steel. The secondary container, if applicable, may be of steel or of concrete or a combination of both. An inner tank made only of pre-stressed concrete is excluded from the scope of this European Standard. This European Standard specifies principles and application rules for the structural design of the “containment” during construction, testing, commissioning, operation (accidental included), and decommissioning. It does not address the requirements for ancillary equipment such as pumps, pumpwells, valves, piping, instrumentation, staircases etc. unless they can affect the structural design of the tank. This European Standard applies to storage tanks designed to store products, having an atmospheric boiling point below ambient temperature, in a dual phase, i.e. liquid and vapour. The equilibrium between liquid and vapour phases being maintained by cooling down the product to a temperature equal to, or just below, its atmospheric boiling point in combination with a slight overpressure in the storage tank. The maximum design pressure of the tanks covered by this European Standard is limited to 500 mbar. For higher pressures, reference can be made to EN 13445, Parts 1 to 5. The operating range of the gasses to be stored is between 0 °C and –165 °C. The tanks for the storage of liquefied oxygen, nitrogen and argon are excluded. The tanks are used to store large volumes of hydrocarbon products and ammonia with low temperature boiling points, generally called “Refrigerated Liquefied Gases” (RLG’s). Typical products stored in the tanks are: methane, ethane, propane, butane, ethylene, propylene, butadiene (this range includes the LNG’s and LPG’s). NOTE Properties of the gases are given in Annex A. The requirements of this European Standard cannot cover all details of design and construction because of the variety of sizes and configurations that may be employed. Where complete requirements for a specific design are not provided, the intention is for the designer, subject to approval of the purchaser's authorized representative, to provide design and details that are as safe as those laid out in this European Standard. This European Standard specifies general requirements for the tank concept, selection and general design considerations.

Design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and -165 °C - General

BS EN 14620-5:2006 工作温度0℃～-165℃液态气体冷冻储存用垂直圆柱平底钢罐现场制作的设计和生产.烘干、清洗和冷却测试

This European Standard specifies the requirements for testing, drying, purging and cool-down of the refrigerated liquefied gas storage tanks. This European Standards deals with the design and manufacture of site built, vertical, cylindrical, flatbottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and –165 °C.

Design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and -165 °C - Testing, drying, purging and cool-down

BS EN 14620-4:2006 工作温度为0℃～-165℃液态气体冷冻储存用垂直圆柱平底钢罐现场制造的设计和生产.绝缘部件

This European Standard specifies the requirements for materials, design and installation of the insulation of refrigerated liquefied gas (RLG) storage tanks. RLG storage tanks store liquefied gas with a low boiling point, i.e. below normal ambient temperature. The concept of storing such products in liquid form and in non-pressurized tanks therefore depends on the combination of latent heat of vaporization and thermal insulation. Consequently thermal insulation for RLG storage tanks is not an ancillary part of the containment system (as for most ambient atmospheric hydrocarbon tanks) but it is an essential component and the storage tank cannot operate without a properly designed, installed and maintained insulation system. The main functions of the insulation in RLG storage tanks are:  to maintain the boil off below the specific limits;  to protect the non low temperature parts/materials of the tank (mainly the outer tank) by maintaining these parts at their required ambient temperature;  to limit the cool-down of the foundations/soil underneath the tank to prevent damage by frost heave;  to prevent/minimize condensation and icing on the outer surfaces of the tank. A wide range of insulation materials is available. However the material properties differ greatly amongst the various generically different materials and also within the same generic group of materials. Therefore within the scope of this European Standard, only general guidance on selection of materials is given. NOTE For general guidance on selection of materials see Annex A. This European Standard deals with the design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and – 165 °C.

Design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and -165 °C - Insulation components

BS EN 14620-3:2006 工作温度0℃～-165℃的储存冷冻液态气体用垂直圆柱平底钢罐现场制造的设计和生产.混凝土部件

This European Standard specifies general requirements for materials, design and construction of the concrete components of the refrigerated liquefied gas storage tanks. This European Standard deals with the design and manufacture of site built, vertical, cylindrical, flatbottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and –165 °C.

Design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and -165 °C - Concrete components

BS EN 14620-2:2006 工作温度为0℃～-165℃液态气体冷冻储存用垂直圆柱平底钢罐现场制造的设计和生产.金属部件

This European Standard specifies general requirements for the materials, design, construction and installation of the metallic components of refrigerated liquefied gas storage tanks. This European Standard deals with the design and manufacture of site built, vertical, cylindrical, flatbottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and –165 °C.

Design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and -165 °C - Metallic components

ANSI/ASTM F1437:2006 倾斜货舱梯子的使用规范

This practice provides design, construction, and installation criteria for inclined ladders to be installed within cargo tanks. Where ladders are attached to platforms, see Fig. 1 and Fig. 2 . Values stated in SI units are to be regarded as the standard. The values stated in parentheses are provided for information purposes only. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Practice for Inclined Cargo Tank Ladders