23.020.10 固定容器和罐 标准查询与下载

ASME STP-PT-005-2006 高压复合氢罐用STP/PT-005设计因数指南

This document provides recommendations to the ASME Hydrogen Project Team for design factors for composite hydrogen tanks. The scope of this study included stationary (e.g., storage) and transport tanks; it does not include vehicle fuel tanks. The report provides recommended design factors relative to short-term burst pressure and interim margins for long-term stress rupture based on a fixed 15-year design life for fully wrapped and hoop wrapped composite tanks with metal liners. These recommended margins are based on the proven experience with existing standards for composite reinforced tanks. Recommendations for further research are also provided, in particular for development of rules that would provide design life dependent design factors relative to stress rupture that would provide a means to design for longer or shorter lives than 15 years, and to provide a method for the manufacturer to determine, by testing, the stress ratio for their fiber reinforcement system.

DESIGN FACTOR GUIDELINES FOR HIGH PRESSURE COMPOSITE HYDROGEN TANKS

DS/EN 13923:2005 纤维缠绕 FRP 压力容器 材料、设计、制造和测试

This European Standard specifies the requirements for the design including raw materials, calculation, manufacturing including composite materials, and testing of seamless Glass Reinforced Plastic (GRP) pressure vessels with protective layer, using only multi-directional filament winding, made in a factory and for use above ground and for storage and processing of fluids.This European Standard covers vessels subject to pressures below 20 MPa and temperatures between - 30 °C and 120 °C.Excluded from this European Standard are transportation vessels, double wall vessels, vessels under negative pressure, vessels which are subjected to the risk of explosion o

Filament-wound FRP pressure vessels - Materials, design, manufacturing and testing

CNS 1324-2005 液化石油气用钢瓶阀

本标准适用于水容积3公升以上至120公升以下，罐装液化丙烷，液化丁烷，液化丙烷，液化丙烯，液化丁烯，液化二丁烯及其它液化石油气等钢瓶阀与配件之相关规定。

Valves for liquefied petroleum gas cylinder

DVS 2205-1 Beiblatt 9-2005 由热塑性塑料制成的罐和设备的计算 由 PVC-C 制成的模塑材料的减少系数 A1

Calculation of tanks and apparatus made of thermoplastics - Reduction coefficients A1 for moulding materials made of PVC-C

DVS 2205-1 Beiblatt 15-2005 由热塑性塑料制成的储罐和设备的计算 在证明 PE 和 PP 的稳定性受介质影响的情况下的折减系数 A2I

Calculation of tanks and apparatus made of thermoplastics - Reduction coefficients A2I in the case of proof of the stability with a media influence for PE and PP

DVS 2205-1 Beiblatt 14-2005 由热塑性塑料制成的罐和设备的计算 由 PVC-U 制成的模塑材料的减少系数 A1

Calculation of tanks and apparatus made of thermoplastics - Reduction coefficients A1 for moulding materials made of PVC-U

DS/EN 14570:2005 液化石油气罐的装备，地上和地下

This standard specifies requirements for the equipping of LPG overground and underground, with a volume not greater than 13m3 manufactured in accordance with EN 12542, EN 14075; or equivalent and have been hydraulically tested. The equipment covered by this standard is directly mounted onto the tank connections.

Equipping of LPG tanks, overground and underground

NF M88-560:2005 家用燃料油、煤油和柴油的地上存储用热塑性固定储油罐.通过阴离子聚合吹塑聚乙烯储油罐、旋转模制聚乙烯和聚酰胺6储油罐.要求和试验方法

Thermoplastics static tanks for above ground storage of domestic heating oils, kerosene and diesel fuels - Blow moulded polyethylene, rotationally moulded polyethylene and polyamide 6 by anionic polymerization tanks - Requirements and test methods.

DVS 2205-1 Beiblatt 21-2005 热塑性塑料制成的容器和设备的计算 PTFE 制成的管道的蠕变断裂强度 最小曲线

Calculation of vessels and equipment made of thermoplastics Creep rupture strength minimum curve for pipes made of PTFE

JB/T 4710-2005 钢制塔式容器

本标准规定了钢制塔式容器的设计、制造、检验与验收的要求。 本标准适用于设计压力不大于35MPa，高度H大于10m、且高度H与平均直径D之比大于5的裙座自支承钢制塔式容器。 本标准不适用于下列塔式容器： a)带有拉牵装置的塔式容器； b)由操作平台联成一体的排塔或塔群； c)带有夹套的塔式容器。

Steel vertical vessels supported by skirt

JB/T 4731-2005 钢制卧式容器

本标准规定了钢制卧式容器(以下简称卧式容器)的设计、制造、检验和验收的要求。 本标准适用于设计压力不大于35MPa，在均布载荷作用下，由两个位置对称的鞍式支座支承的卧式容器。 本标准不适用于下列卧式容器： a)直接火焰加热及受核辐射作用的卧式容器； b)经常搬运的卧式容器； c)要求进行疲劳分析的卧式容器； d)带夹套的卧式容器。

Steel horizontal vessels on saddle supports

DVS 2205-1 Beiblatt 10-2005 热塑性塑料制成的储罐和设备的计算 PP 模制材料的衰减系数 A1

Calculation of tanks and apparatus made of thermoplastics - Reduction coefficients A1 for moulding materials made of PP

BS EN 13341:2005+A1:2011 家用燃料油,煤油和柴油燃料的地上存储用热塑性固定储油罐.阴离子聚合聚酰胺6制的吹塑,旋转模制聚乙烯罐和旋转模制罐.试验方法和要求

!This document specifies requirements for materials, physical properties and performance of single blow moulded and rotationally moulded polyethylene tanks and of rotationally moulded tanks made of anionically polymerized polyamide 6, with or without reinforcements, for above ground storage of domestic heating oil, kerosene and diesel fuels for the supply of building heating/cooling systems. It is only applicable to static blow moulded and rotationally moulded polyethylene tanks and to rotationally moulded tanks made of anionically polymerized polyamide 6 that are subject to atmospheric pressure, but not subject to any external loading and have a capacity from 400 l up to 10 000 l." !deleted text"

Static thermoplastic tanks for above ground storage of domestic heating oils, kerosene and diesel fuels. Blow moulded and rotationally moulded polyethylene tanks and rotationally moulded tanks made of anionically polymerized polyamide 6. Requirements and

BS EN 13341:2005 家用燃料油、煤油和柴油燃料的地上存储用热塑性固定储油罐.通过阴离子聚合吹塑聚乙烯储油罐、旋转模制聚乙烯和聚酰胺储油罐.要求和试验方法

This document specifies requirements for materials, physical properties and performance of single blow moulded and rotationally moulded polyethylene tanks or polyamide 6 (by anionic polymerisation) tanks, with or without reinforcements, for above ground storage of domestic heating oil, kerosene and diesel fuels. It is only applicable to static blow moulded and rotationally moulded polyethylene tanks and polyamide 6 (by anionic polymerisation) tanks that are subject to atmospheric pressure and have a capacity from 450 l up to 10 000 l. This document does not consider the consequences of wind or snow loading which is considered to be an installation issue.

Thermoplastics static tanks for above ground storage of domestic heating oils, kerosene and diesel fuels - Blow moulded polyethylene, rotationally moulded polyethylene and polyamide 6 by anionic polymerization tanks - Requirements and test methods

DS/EN 12285-2:2005 车间装配式钢罐 第2部分：用于地上储存易燃和非易燃水污染液体的卧式圆柱形单皮和双皮罐

This standard specifies the requirements for metallic shop fabricated cylindrical, horizontal steel tanks, single and double skin for the aboveground storage of water polluting liquids (both flammeable and non-flammeable).

Workshop fabricated steel tanks - Part 2: Horizontal cylindrical single skin and double skin tanks for the aboveground storage of flammable and non-flammable water polluting liquids

NF T58-205:2005 吹模或旋转模制聚乙烯热塑性罐.地上化学制剂储罐.要求和试验方法

Thermoplastic tanks made from blow or rotational moulded polyethylene - Tanks for the above ground storage of chemicals - Requirements and test methods.

EN 13341:2005 家用燃料油,煤油和柴油地上储存用热塑性固定油箱.利用阴离子聚合吹塑成形聚乙烯油箱,旋转模制聚乙烯和聚酰胺6油箱.要求和试验方法

This document specifies requirements for materials, physical properties and performance of single blow moulded and rotationally moulded polyethylene tanks and of rotationally moulded tanks made of anionically polymerized polyamide 6, with or without reinforcements, for above ground storage of domestic heating oil, kerosene and diesel fuels forThe supply of building heating/cooling systems.

Static thermoplastic tanks for above ground storage of domestic heating oils, kerosene and diesel fuels - Blow moulded and rotationally moulded polyethylene tanks and rotationally moulded tanks made of anionically polymerized polyamide 6 - Requirements an

LST EN 14015-2005 用于在环境温度及以上温度下储存液体的现场建造、立式、圆柱形、平底、地上、焊接钢罐的设计和制造规范

Specification for the design and manufacture of site built, vertical, cylindrical, flat-bottomed, above ground, welded, steel tanks for the storage of liquids at ambient temperature and above

DS/EN 13121-4:2005 地上使用的 GRP 储罐和容器 第4部分：交付、安装和维护

This document gives requirements for delivery, installation and maintenance of GRP tanks and vessels in accordance with prEN 13121-3.

GRP tanks and vessels for use above ground - Part 4: Delivery, installation and maintenance

LST EN 13121-4-2005 地上使用的 GRP 储罐和容器 第4部分：交付、安装和维护

GRP tanks and vessels for use above ground - Part 4: Delivery, installation and maintenance