23.020.10 固定容器和罐 标准查询与下载

BS EN 14015:2005 在室温和高于室温下液体储存用现场建造的立式、圆柱形、平底、地上用焊接钢罐的设计和制造规范

Specification for the design and manufacture of site built, vertical, cylindrical, flat-bottomed, above ground, welded, steel tanks for the storage of liquids at ambient temperature and above

BS EN 14015:2004 在室温和高于室温下液体储存用现场建造的立式、圆柱形、平底、地上用焊接钢罐的设计和制造规范

1 This document specifies the requirements for the materials, design, fabrication, erection, testing and inspection of site built, vertical, cylindrical, flat bottomed, above ground, welded, steel tanks for the storage of liquids at ambient temperatures and above, and the technical agreements that need to be reached (see Annex A). This document does not apply to tanks where the product is refrigerated to maintain it as a liquid at atmospheric pressure (see prEN 14620). This document is concerned with the structural integrity of the basic tank structure and does not provide requirements for considering process design, operational issues, safety and firefighting facilities, in-service inspection, maintenance or repair. These aspects are covered in detail in other Codes of Practice (see Annex B). 2 This document applies to closed-top tanks, with and without internal floating covers (see Annex C) and open-top tanks, with and without floating roofs (see Annexes D and E). It does not apply to 'lift-type' gas holders. 3 This document applies to storage tanks with the following characteristics: a) design pressure less than 500 mbar and design internal negative pressure not lower than 20 mbar (see 5.1 for pressure limitations); b) design metal temperature not lower than -40 ℃ and not higher than +300 ℃ (see 5.2.2); c) maximum design liquid level not higher than the top of the cylindrical shell. 4 The limits of application of this document terminate at the following locations. — face of the first flange in a bolted flange connection; — first threaded joint on the pipe or coupling outside of the tank shell, roof or bottom; — first circumferential joint in a pipe not having a flange connection. 5 This document is applicable to steel tanks with a maximum design strength ≤ 260 N/mm. 6 In addition to the definitive requirements, this document also requires the items detailed in Annex A to be documented. For compliance with this document, both the definitive requirements and those required in Clause 4 have to be satisfied. note:1) All pressures are in mbar gauge unless otherwise stated.

Specification for the design and manufacture of site built,vertical,cylindrical,flat-bottomed,above ground,welded,steel tanks for the storage of liquids at ambient temperature and above

EN 12285-2:2005 工厂制造的钢罐.第2部分:易燃和不易燃水污染液体的地上储存用卧式圆柱形单层和双层钢罐

This document specifies the requirements for metallic shop fabricated cylindrical, horizontal steel tanks, single and double skin forThe aboveground storage of water polluting liquids (both flammable and non-flammable) withinThe following limits:？ from 800 mm up to 3 000 mm nominal diameter and, ？ up to a maximum overall length of 6 timesThe nominal diameter and, ？ for liquids with a maximum density of up to 1,9 kg/l and, ？ with an operating pressure (Po) of maximum 1,5 bar (abs.) and, ？ where double skin tanks with a vacuum leak detection system are usedThe cinematic viscosity of the stored media shall not exceed 5 × 10-3 m2/s.

Workshop fabricated steel tanks - Part 2: Horizontal cylindrical single skin and double skin tanks for the aboveground storage of flammable and non-flammable water polluting liquids

DIN EN 14015:2005 在室温及高于室温下液体储存用平底、立式、圆柱形、现场建造的地面上可焊钢罐的设计和制造规范

This European Standard specifies the requirements for the materials, design, fabrication, erection, testing and inspection of site built, vertical, cylindrical, flat bottomed, above ground, welded, steel tanks with a maximum design stress of 260 N/mm2 for the storage of liquids at ambient temperatures and above, and the technical agreements that need to be reached. It applies to closed-top tanks, with and without internal floating covers, and open-top tanks, with and without floating roofs. It does not apply to 'lift-type' gas holders.

Specification for the design and manufacture of site built, vertical, cylindrical, flat-bottomed, above ground, welded, steel tanks for the storage of liquids at ambient temperature and above; German version EN 14015:2004

DS/EN 14015:2005 用于在环境温度及以上温度下储存液体的现场建造、立式、圆柱形、平底、地上、焊接钢罐的设计和制造规范

This European Standard specifies the requirements for the materials, design, fabrication, erection, testing and inspection of site built, vertical, cylindrical, flat bottomed, above ground, welded, steel tanks for the storage of liquids at ambient temperatures and above, and the technical agreements that need to be reached (see Annex A). This document does not apply to tanks where the product is refrigerated to maintain it as a liquid at atmospheric pressure (see prEN 14620). This document is concerned with the structural integrity of the basic tank structure and does not provide requirements for considering process design, operational issues, safety and fi

Specification for the design and manufacture of site built, vertical, cylindrical, flat-bottomed, above ground, welded, steel tanks for the storage of liquids at ambient temperature and above

BS EN 13121-4:2005 地面用GRP槽罐和容器.交付、安装和维修

This document gives requirements for delivery, installation and maintenance of GRP tanks and vessels in accordance with prEN 13121-3.

GRP tanks and vessels for use above ground - Delivery, installation and maintenance

LST EN 13160-5-2005 泄漏检测系统 第5部分：储罐液位计泄漏检测系统

Leak detection systems - Part 5: Tank gauge leak detection systems

CNS 9792-2005 压力容器之管板

本标准适用于多管圆筒型热交换器之管板计算：其适用方法参照CNS 9788。

Flat tube sheet for pressure vessels

CNS 9795-2005 压力容器之伸缩接头

本标准适用于为吸收CNS 9788〔压力容器(通则)〕中第3节压力容器之等级分类中所规定之第二种及第三种压力容器之热交换器、附夹套容器等因温度变化等所产生在轴方向之伸缩而设置之伸缩接头之设计、制造及检查方法。其适用之方法系依CNS 9788第6.12节伸缩接头之规定。但对于第3

Expansion joint for pressure vessels

CNS 9797-2005 压力容器之夹套

本标准适用于熔接方式装设于压力容器对侧之压力室（以下称夹套）之构造。其适用之方法，依CNS 9788〔压力容器(通则)〕之规定。．将压力容器及其内容物加热。．将压力容器及其内容物冷却。．于压力容器设密封隔热室。

Jacket for pressure vessels

CNS 9789-2005 压力容器之胴体及端板

本标准适用于受内压或外压之胴体与端板之计算。其适用之方法请参考CNS 9788〔压力容器(通则)〕之规定。备考1. 本标准中规定之设计法(1)，系使用于CNS 9788第3节（压力容器之等级分类）中所定之第2种容器及第3种容器之计算；设计法(2)则使用于第1种容器之计算。2. 本标准所引

Shell and head of pressure vessels

CNS 9794-2005 压力容器以牵条支撑之平板

本标准适用于压力容器以棒、管或板(以下称为牵条)支撑时，其平端板、管板等之强度计算。且相关工法亦应适用CNS 9788〔压力容器(通则)〕之规定。

Stayed plate for pressure vessels

EN 13121-4:2005 地上用GRP槽罐和容器.第4部分:交付,安装和维修.合并勘误表-2007年2月

This document gives requirements for delivery, installation and maintenance of GRP tanks and vessels in accordancewith prEN 13121-3.

GRP tanks and vessels for use above ground - Part 4: Delivery, installation and maintenance

NF E86-601-5:2005 检漏系统.第5部分:液面计检漏系统

Leak detection systems - Part 5 : tank gauge leak detection systems.

UL 58 BULLETINS-2005 CSDS 6/30/2005 (24p)

These requirements cover horizontal atmosheric-type steel tanks intended for the storage underground of flammable and combustible liquids. These tanks are intended for installation and use in accordance with the Standard for the Installation of Oil-Burning Equipment, NFPA 31, and the Flammable and Combustible Liquids Code, NFPA 30, of the National Fire Protection Association. Tanks covered by these requirements are cylindrical tanks which are fabricated, inspected, and tested for leakage before shipment from the factory as completely assembled vessels.

CSDS 6/30/2005 (24p)

ANSI/AHRI 495-2005 制冷剂集液器的性能评级

This standard applies to separately installed Refrigerant Liquid Receivers for field-erected systems only.

Performance Rating of Refrigerant Liquid Receivers

ANSI/NSF WSCPST 2000(i2)-2005 水资源委员会(WSC)PST-2000压力储水罐标准

Water Systems Council (WSC) PST-2000 Pressurized Water Storage Tank Standard

ANSI/NSF WSCPST 2000-2005 压水储罐

Pressurized Water Storage Tank

ANSI/NSF WSCPST-2005 加压蓄水箱

To establish a Standard for minimum performance and construction requirements for pressurized storage tanks for service in water well systems.

Pressurized Water Storage Tank

DIN EN 13160-5:2004 检漏系统.第5部分:液面计检漏系统

This standard specifies the requirements for leak detection systems - class IV for use only with liquids as defined in the scope of EN 13352.

Leak detection systems - Part 5: Tank gauge leak detection systems; German version EN 13160-5:2004