共找到 599 条与 固定容器和罐 相关的标准,共 40 页
This document specifies requirements for above ground single static thermoplastic tanks of volume 450 l to 10 000 l, which can be used for the storage of liquids other than water including chemicals classified as dangerous goods. This document only applies to tanks manufactured by blow moulding or rotational moulding of polyethylene, with or without reinforcements, which are not subjected to pressures exceeding ±5 kPa (±0,05 bar). Except for periodic temperature fluctuation their normal operating temperature does not exceed 25 ℃. This document only applies to tanks with a maximum lifetime of 10 years. This document specifies permitted materials, performance requirements and test methods and factory production control tests. This document does not consider wind and snow loads. NOTE National and/or International regulations above and beyond the requirements of this standard may apply to the storage of liquids and the installation of tanks.
Thermoplastics tanks made from blow or rotational moulded polyethylene. Tanks for the above ground storage of chemicals. Requirements and test methods
This document specifies the requirements for leak detection systems - class IV for use only with liquids as defined in the scope of EN 13352.
Leak detection systems - Tank gauge leak detection systems
本标准适用于以导管供应天然气(以下简称燃气)为燃料之公用事业用户为保障其安全所装设之紧急遮断装置,包括接收由天然气泄漏警报器所发出信号及其它信号面输出遮断信号之控制器以及接到此输出能自动切断燃气流通之遮断阀等二单元。
Automatic emergency shut down device for natural gas system
MIL-S-51537 remains inactive for new design, however, the document is valid for use.
SMOKE POT, FLOATING, SGF2, AN-M7A1; COMPONENTS FOR
MIL-S-51235C remains inactive for new design, however, the document is valid for use.
SMOKE POT, FLOATING, SGF2, AN-M7A1
MIL-D-13242 remains inactive for new design, however, the document is valid for use.
DRUM, PACKING; FOR M4A2 FLOATING SMOKE POT
GRP tanks and vessels for use above ground - Part 2: Composite materials - Chemical resistance
GRP tanks and vessels for use above ground - Part 1: Raw materials - Specification conditions and acceptance conditions
Contains provisions for sectional steel tanks, of two types of construction, with or without covers, for the storage of liquids at or above ground level.
The design and construction of sectional steel tanks for storage of liquids at or above ground level
MIL-PRF-53007B, dated 2 January 1996, has been reviewed and determined to be valid for use in acquisition
ROLLER KIT, ROLLER, MINE CLEARING: TRACK-WIDTH, TANK-MOUNTED
本标准与GB12337-1998《钢制球形储罐》和GB/T17261-1998《钢制球形储罐型式与基本参数》配套使用。
Integrated forging reinforcement for spherical tanks
This standard gives requirements for chemical resistance of composite materials used for GRP tanks and vessels for storage or processing of fluids, for use above ground. The tanks or vessels may be factory made or site built, with or without lining.
GRP tanks and vessels for use above ground - Part 2: Composite materials - Chemical resistance
Specification for the design and manufacture of site built, vertical, cylindrical, flat-bottomed, above ground, welded, steel tanks for the storage of liquids at ambient temperature and above
This European Standard gives requirements for chemical resistance of composite materials used for GRP tanks and vessels for storage or processing of fluids, for use above ground. The tanks or vessels may be factory made or site built, with or without lining.
GRP tanks and vessels for use above ground - Part 2: Composite materials - Chemical resistance; German version EN 13121-2:2003
This document specifies the requirements for the materials, design, fabrication, erection, testing and inspection of site built, vertical, cylindrical, flat bottomed, above ground, welded, steel tanks for the storage of liquids at ambient temperatures and above, and the technical agreements that need to be reached (see Annex A).
Specification for the design and manufacture of site built, vertical, cylindrical, flat-bottomed, above ground, welded, steel tanks for the storage of liquids at ambient temperature and above
The general design geometry herein defined applies to both a separate adaptor accessory mating two booms of different geometry as well as boom end connectors (see Terminology F818). Interconnectibility is intended to facilitate mating of oil spill response booms of various sizes, strengths, design, and manufacture. The use of this general design geometry in no way guarantees the effective performance of the linked boom sections, since each boom’s design and the environmental conditions at each incident govern overall performance. 1.1 This specification covers design criteria requirements, design geometry, material characteristics, and desirable features for oil spill response boom slide connections. These criteria are intended to define minimum mating characteristics and are not intended to be restricted to a specific configuration. 1.2 The specification defines the geometry required to mate with typical Universal slide connectors or Specification F962 connectors with web thickness up to 0.3 in. Some very heavy-duty or PVC connectors may exceed this dimension and not be compatible. 1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.
Standard Specification for Oil Spill Response Boom Connection: Slide Connector
This standard gives requirements for specification and acceptance conditions of raw materials for GRP tanks and vessels with or without lining for storage or processing of fluids, factory made or site built, non pressurised or pressurised, for use above ground.
GRP tanks and vessels for use above ground - Part 1: Raw materials - Specification conditions and acceptance conditions
Calculation of storage tanks and equipment made of thermoplastic plastic Vertical circular atmospheric storage tanks
"Calculation of tanks and apparatus made of thermoplastics - Vertical round, non-pressurised tanks - Flat roofs"
Calculation of tanks and apparatus made of thermoplastics - Welded stationary tanks in the case of installation in buildings
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号