23.020.10 固定容器和罐 标准查询与下载

CNS 10216-2001 压力容器之用词

本标准适用于压力容器样造有关之共同用词及意义。但其在 CNS 11835 〔铁钢热处理词汇〕、CNS 11836 〔铁钢词汇（制品及品质）〕及 CNS 12831 〔焊接词汇〕等有关压力容器构造标准中用词得依各该规定。备考：本标准中用｛ ｝ 表示之单位、数值系惯用单位、并记供作参考。

Glossary of terms used in pressure vessels

CNS 10215-2001 压力容器之检窗口

本标准适用于供设计压力未满 30 Mpa｛300kgf∕cm2｝压力容器使用之窥视窗（以下窥视窗）构造及有关检窗口玻璃之规定。备考 1：本标准引用之标准如下： CNS 9788 〔压力容器（通则）〕CNS 9789 〔压力容器之胴体及端板〕 CNS 9790 〔压力容器之孔补强〕 CNS 9791 〔压力容器

Sight glasses for pressure vessels

CNS 9798-2001 非圆型胴体之压力容器

本标准适用于截面为长方形或长圆形之胴体（以下称为 “非圆形”。）之压力容器之构造加以规定。其适用方法及范围，依如下之规定。（1）非圆形胴体之压力容器，适用 CNS 9788 中规定之第 2 容器或第 3 容器。（2）非圆形胴体之范围为由胴体板、补强材料、隔板、牵板、胴体凸

Pressure vessel of noncircular cross section

CNS 9793-2001 压力容器之盖板

本标准适用于压力容器以螺栓固定及嵌于胴体上，而可拆卸之平盖板等之计算，其适用方法参照 CNS 9788 之规定。另有关需繁拆卸构造者，应参考 CNS 9788 之规定。备考 1：本标准中所引用之标准如下所示。CNS 10216 〔压力容器之用词〕 CNS 9788 〔压力容器（通则）〕CNS 9789

cover plate for pressure vessels

CNS 9791-2001 压力容器螺栓之固定凸缘

本标准适用于螺栓固定凸缘之应力计算法。备考：1. 使用非金属全垫圈于全座凸缘之计算法纳入冷录 1，金属面接触凸缘之计算法纳入附录 2，反向凸缘之计算法纳入附录 3 中，而其适用方法则参照 CNS 9788 〔压力容器（通则 ）〕。2. 本标准中所定计算法，系为了计算，评估在垫圈

Beltled flange for pressure vessels

CNS 9796-2001 以鞍座支撑之卧型压力容器

本标准适用于以等分布载重作用，其鞍座位置对称之两个鞍座支撑之卧型圆筒形压力容器之鞍座周围应力计算。备考 1. 本标准引用之标准如下：CNS 10216 〔压力容器之用词〕 CNS 9788 〔压力容器（通则）〕2. 在本标准中加以括号｛ ｝ 表示之单位及数值，系依习用单位制，并列以

Saddle supported horizontal pressure vessels

CNS 9803-2001 压力容器熔接施工方法之确认试验

本标准适用于 CNS 9788 〔压力容器（通则）〕国家标准中有关熔接施工方法之确认试验加以规定。亦可适用于锅炉。备考 1：本标准所引用之标准，如附表 6 所示。2：在本标准中，｛ ｝ 表示之单位及数值，系依习用之单位制，并记供参考。

Welding procedure qualification test for pressure vessels

CNS 9790-2001 压力容器之孔补强

本标准适用于压力容器之胴板及端板上，装置孔时之补强。备考 1：本标准中规定之设计法（1），系使用于 CNS 9788 第 3 节，（压力容器之等级分类）中所规定之第 2 及第 3 种之计算。设计法（2）（3）则使用于第 1 种容器之计算。2：本标准所引用之其它标准如下 CNS 10216 〔

Opening pressure vessels

DS/EN 12573-4:2001 焊接静态非加压热塑性塑料罐 第4部分：法兰接头的设计和计算

This part af this standard specifies the design and calculation of circular flanged joints, fabricated in thermoplastic materials.

Welded static non-pressurised thermoplastic tanks - Part 4: Design and calculation of flanged joints

DS/EN 12573-1:2001 焊接静态非加压热塑性塑料罐 第1部分：一般原则

This standard specifies general principles for welded static non-pressurised thermoplastic tanks. It applies to work shop and site fabrications. The standard covers tanks with a capacity of 0,45 m3 (450 litres) and above.

Welded static non-pressurised thermoplastic tanks - Part 1: General principles

DS/EN 12573-2:2001 焊接静态非加压热塑性塑料罐 第2部分：立式圆柱罐的计算

This standard establishes rules for the design and calculation of welded static, vertical, non-pressurised, cylindrical, flat-bottom thermoplastic tanks.

Welded static non-pressurised thermoplastic tanks - Part 2: Calculation of vertical cylindrical tanks

DS/EN 12573-3:2001 焊接静态常压热塑性塑料罐 第3部分：单层矩形罐的设计和计算

This standard specifies the design and calculation for single skin rectangular tanks, abricated from thermoplastics materials.

Welded static non-pressurised thermoplastic tanks - Part 3: Design and calculation for single skin rectangular tanks

ANSI/ASTM D4097:2001 接触制模纤维玻璃增强的热固树脂耐腐蚀罐用规范

This specification covers cylindrical tanks fabricated by contact molding for above-ground vertical installation, to contain aggressive chemicals at essentially atmospheric pressure, and made of a commercial-grade polyester or vinyl ester, resin. Included are requirements for materials, properties, design, construction, dimensions, tolerances, workmanship, and appearance. This specification does not cover the design of vessels intended for pressure above hydrostatic, vacuum conditions, except as classified herein, or vessels intended for use with liquids heated above their flash points. The values given in parentheses are provided for information purposes only. Note 1Special design consideration should be given to vessels subject to superimposed mechanical forces, such as earthquakes, wind load, or agitation, to vessels subject to service temperature in excess of 180?F (82?C), and to vessels with unsupported bottoms. Note 2 -There is no similar or equivalent ISO standard. The following safety hazards caveat pertains only to the test method portion, Section 11, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Specification for Contact-Molded Glass-Fiber-Reinforced Thermoset Resin Corrosion-Resistant Tanks

UL 1746 BULLETINS-2001

These requirements cover preengineered corrosion protection systems. Part i covers factory-installed galvanic-type cathodic protection. Part ii covers factory assembled composite systems. Part iii covers factory assembled jacket systems. Part iv covers factory assembled coated systems. These corrosion protection systems are intended to be completely installed at the factory on carbon steel underground storage tanks. Part ii of this standard covers fiberglass reinforced plastic (FRP), materials only. Part iii of this standard covers FRP, polyurethane, polyurea and high density polyethylene (HDPE) materials only. Part iv covers polyurethane materials only. These corrosion protection systems are intended to be installed, operated and maintained in accordance with the manufacturer's instructions.

11/19/2001 (4p), 10/01/2001 (4p)

LST EN 976-2-2000 玻璃增强塑料（GRP）地下储罐 用于非压力储存液态石油基燃料的卧式圆柱形储罐 第2部分：单壁储罐的运输、装卸、储存和安装

Underground tanks of glass-reinforced plastics (GRP) - Horizontal cylindrical tanks for the non-pressure storage of liquid petroleum based fuels - Part 2: Transport, handling, storage and installation of single wall tanks

LST EN 976-1-2000 玻璃钢（GRP）地下储罐 非压力储存液态石油燃料的卧式圆柱形储罐 第1部分：单壁储罐的要求和试验方法

Underground tanks of glass-reinforced plastics (GRP) - Horizontal cylindrical tanks for the non-pressure storage of liquid petroleum based fuels - Part 1: Requirements and test methods for single wall tanks

LST EN 978-2000 玻璃钢（GRP）地下储罐 α 因子和 β 因子的测定

Underground tanks of glass-reinforced plastics (GRP) - Determination of factor alpha and factor beta

LST EN 977-2000 玻璃钢（GRP）地下储罐 一侧接触液体的方法

Underground tanks of glass-reinforced plastics (GRP) - Method for one side exposure to fluids

LST EN 12573-2-2000 焊接静态非加压热塑性塑料罐 第2部分：立式圆柱罐的计算

Welded static non-pressurised thermoplastic tanks - Part 2: Calculation of vertical cylindrical tanks

LST EN 12573-1-2000 焊接静态非加压热塑性塑料罐 第1部分：一般原则

Welded static non-pressurized thermoplastic tanks - Part 1: General principles