23.020.30 压力容器、气瓶 标准查询与下载
共找到 2470 条与 压力容器、气瓶 相关的标准，共 165 页
LPG equipment and accessories -- Welded steel pressure vessels for LPG road tankers -- Design and manufacture
- ICS
- 23.020.30
- CCS
- 发布
- 2021-05-20
- 实施
- 2021-05-20
Unfired pressure vessels. Fabrication
- ICS
- 23.020.30
- CCS
- 发布
- 2021-05-20
- 实施
- 2021-05-20
Unfired pressure vessels – Part 5: Inspection and testing
- ICS
- 23.020.30
- CCS
- 发布
- 2021-05-19
- 实施
- 2021-05-19
Unfired pressure vessels – Part 6: Requirements for the design and fabrication of pressure vessels and pressure parts constructed from spheroidal graphite cast iron
- ICS
- 23.020.30
- CCS
- 发布
- 2021-05-19
- 实施
- 2021-05-19
Unfired pressure vessels – Part 3: Design
- ICS
- 23.020.30
- CCS
- 发布
- 2021-05-19
- 实施
- 2021-10-01
Unfired pressure vessels – Part 10: Additional requirements for pressure vessels of nickel and nickel alloys
- ICS
- 23.020.30
- CCS
- 发布
- 2021-05-19
- 实施
- 2021-05-19
Unfired pressure vessels – Part 4: Fabrication
- ICS
- 23.020.30
- CCS
- 发布
- 2021-05-19
- 实施
- 2021-05-19
Unfired pressure vessels – Part 1: General
- ICS
- 23.020.30
- CCS
- 发布
- 2021-05-19
- 实施
- 2021-05-19
This document specifies requirements for unfired pressure vessels and their parts made of aluminium and aluminium alloys in addition to the general requirements for unfired pressure vessels under EN 13445:2019 Parts 1 to 5. This document specifies unfired pressure vessels for loads up to 500 full cycles. NOTE Cast materials are not included in this version. Details regarding cast materials will be subject to an amendment to or a revision of this document.
Unfired pressure vessels - Part 8: Additional requirements for pressure vessels of aluminium and aluminium alloys
- ICS
- 23.020.30
- CCS
- 发布
- 2021-05-12
- 实施
- 2021-08-31
This Part 10 of this document specifies requirements for unfired pressure vessels and their parts made of nickel and nickel alloys (see 3.1) in addition to the general requirements for unfired pressure vessels under EN 13445-1:2019, EN 13445-2:2019, EN 13445-3:2019, EN 13445-4:2019 and EN 13445-5:2019. NOTE Cast materials are not included in this version. Details regarding cast materials will be subject to an amendment to or a revision of this document.
Unfired pressure vessels - Part 10: Additional requirements for pressure vessels of nickel and nickel alloys
- ICS
- 23.020.30
- CCS
- 发布
- 2021-05-12
- 实施
- 2021-08-31
1.1 This practice is intended to satisfy the demand for information on the basic procedures for the safe handling and transfilling of small (not bulk) paintball compressed air cylinders commonly used with a paintball marker for propulsion of a paintball. This standard does not address issues dealing with the transfilling, storage, and handling of supply cylinders that may be used in transfilling smaller cylinders. 1.2 The compressed air fill procedures are written for the pressure cylinder transfilling method most commonly used by paintball field or store operators, or both. 1.3 This document should not be confused with federal, state, provincial, or municipal specifications or regulations; insurance requirements; or national safety codes. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations, such as and not limited to DOT, CGA, and OSHA, prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Practice for Transfilling Compressed Air or Nitrogen and Safe Handling of Small Paintball Cylinders
- ICS
- 23.020.30
- CCS
- 发布
- 2021-05-01
- 实施
Unfired pressure vessels - Part 5: Inspection and testing
- ICS
- 23.020.30
- CCS
- 发布
- 2021-05-00
- 实施
Unfired pressure vessels - Part 3: Design
- ICS
- 23.020.30
- CCS
- 发布
- 2021-05-00
- 实施
Unfired pressure vessels - Part 6: Requirements for the design and fabrication of pressure vessels and pressure parts constructed from spheroidal graphite cast iron
- ICS
- 23.020.30
- CCS
- 发布
- 2021-05-00
- 实施
本标准是针对安装在按GB 50516或GB 50156设计建设的加氢站上使用的、公称工作压力大于等于35MPa且不大于87.5MPa、设计温度不低于-40°C且不高于85°C、贮存介质为车用氢气的加氢站用储氢气瓶制定的技术要求。 标准的编制参考采用了EN17533-2020《Gaseous hydrogen— Cylinders and tubes for stationary storage》的部分内容，以及团体标准T/CATSI 05003-2020《加氢站储氢压力容器专项技术要求》中对材料的要求；规定了站用储氢气瓶的基本安全要求，站用储氢气瓶除应符合相应气瓶产品标准外，还应满足本标准的规定。
Safety technical requirements for high-pressure hydrogen storage cylinders used in hydrogen refueling stations
- ICS
- 23.020.30
- CCS
- C333
- 发布
- 2021-04-23
- 实施
- 2021-04-23
本标准是结合TSG 23-2021《气瓶安全技术规程》和TSG 07-2019《特种设备生产和充装单位许可规则》的相关要求，燃气瓶阀的自动装配及检测线应当具备的基本要求和特殊要求进行了明确和细化，为今后燃气瓶阀的设备采购、评审机构的鉴定评审、型式试验机构的制造监督检验等提供依据。 本标准对燃气瓶阀的自动装配及检测线的使用环境、气源、电气设备、数据采集与处理、流水线及自动化要求进行了规定，并对能否达到标准要求的指标提出了适用的检测方法及判定规则。
Safety technical requirements for automatic assembly and testing line of gas cylinder valves
- ICS
- 23.020.30
- CCS
- C333
- 发布
- 2021-04-23
- 实施
- 2021-04-23
本标准规定了气瓶安全泄压装置用玻璃泡的技术要求、检查与试验方法、检验规则、使用说明书和产品数据单、标志、包装、贮运等。 本标准修改采用GB 18428-2010《自动灭火系统用玻璃球》，与GB 18428-2010的相比较主要修改有： 1）玻璃泡公称动作温度不同，本标准根据车用气瓶安全泄压装置动作温度确定，为110℃； 2）删去了快速响应玻璃泡和标准响应玻璃泡的定义和试验相关要求； 3）删去了光褪色试验和工作液挥发试验。
Specifications for glass bulbs used in safety pressure relief devices for gas cylinders
- ICS
- 23.020.30
- CCS
- C333
- 发布
- 2021-04-23
- 实施
- 2021-04-23
本标准规定了车用压缩氢气储氢系统气体循环试验方法及试验装置的基本要求；标准中提出的试验方法要求，主要依据GB/T 35544《车用压缩氢气铝内胆碳纤维全缠绕气瓶》、T/CATSI 02 007《车用压缩氢气塑料内胆碳纤维全缠绕气瓶》、T/CATSI 02 010《气瓶气密性氦泄漏检测方法》、并参考了GTR No. 13、USO19881以及SAE J2579，并结合了试验实践。 本标准适用于车用储氢系统的氢气循环试验和渗透试验，具体包括公称工作压力不大于35MPa（表压）的车用氢气瓶的氢气循环试验及常温渗透试验，以及公称工作压力不大于70MPa的车用氢气瓶的使用性能试验中的常温和极限温度气压循环试验及极限温度渗透试验；不适用于内装填料的吸附储氢气瓶；站用压缩氢气储氢系统等可参照执行
Gas circulation test method for hydrogen storage system
- ICS
- 23.020.30
- CCS
- C333
- 发布
- 2021-04-23
- 实施
- 2021-04-23
本标准规定了使用环境温度为-40℃～+60℃，公称工作压力为不大于2.5MPa，介质符合GB/T 11174液化石油气钢瓶上的液化石油气智能瓶阀的型号编制、结构型式及基本尺寸、技术要求、检查与试验方法、检验规则、标志、包装、贮运等；旨在规范、提升液化石油气智能瓶阀的行业产品质量及相关技术要求。 本标准的编制基于GB/T 7512-2018《液化石油气瓶阀》及T/CATSI 02006-2019《液化石油气瓶阀》，对左旋螺纹、电子身份标签材料、限充装置性能及耐用性、阀的智能充装设备及后台管理等做了相应的要求。
Liquefied Petroleum Gas Smart Bottle Valve
- ICS
- 23.020.30
- CCS
- C333
- 发布
- 2021-04-23
- 实施
- 2021-04-23
LPG equipment and accessories - Welded steel pressure vessels for LPG road tankers - Design and manufacture
- ICS
- 23.020.30
- CCS
- 发布
- 2021-04-00
- 实施
- 2021-04-01
