23.020.30 压力容器、气瓶 标准查询与下载
共找到 2470 条与 压力容器、气瓶 相关的标准，共 165 页
Gas cylinders－Refillable seamless steel－Performance tests－Part 4：Flawed-cylinder cycle test
- ICS
- 23.020.30
- CCS
- 发布
- 20201230
- 实施
- 20201230
Gas cylinders — Compatibility of cylinder and valve materials with gas contents — Part 2: Non-metallic materials
- ICS
- 23.020.30
- CCS
- 发布
- 20201230
- 实施
- 20201230
Gas cylinders－Refillable seamless steel－Performance tests－ Part 3：Fracture performance tests－Cyclical burst tests
- ICS
- 23.020.30
- CCS
- 发布
- 20201230
- 实施
- 20201230
Gas cylinders－Parallel threads for connection of valve to gas cylinders－Part 2：Gauge inspection
- ICS
- 23.020.30
- CCS
- 发布
- 20201230
- 实施
- 20201230
Gas cylinders－Refillable seamless steel－Performance tests－Part 1：Philosophy, background and conclusions
- ICS
- 23.020.30
- CCS
- 发布
- 20201230
- 实施
- 20201230
Gas cylinders — Refillable composite gas cylinders and tubes — Part 3: Fully wrapped fibre reinforced composite gas cylinders and tubes up to 450 L with non-load sharing metallic or non-metallic liners
- ICS
- 23.020.30
- CCS
- 发布
- 20201230
- 实施
- 20201230
Stress and fatigue analyses for pressure vessels
- ICS
- 23.020.30
- CCS
- 发布
- 20201229
- 实施
- 20201229
Saddle supported horizontal pressure vessels
- ICS
- 23.020.30
- CCS
- 发布
- 20201229
- 实施
- 20201229
LPG equipment and accessories – Welded steel pressure vessels for LPG road tankers – Design and manufacture
- ICS
- 23.020.30
- CCS
- 发布
- 2020-12-22
- 实施
- 2020-12-22
本文件规定了复合材料固化用热压罐（以下简称为热压罐）的术语和定义、型号及基本参数、基本要求、技术要求和试验方法、检验规则、标志、运输和贮存、安装维护和质量承诺。 本文件适用于电加热方式的碳纤维、蜂窝件和芳纶材料固化用热压罐（以下简称热压罐），最高工作压力不大于4.2 MPa、最高工作温度不大于250 ℃、内径不大于3 m，容积不大于50 m3。
Autoclave for curing composite materials
- ICS
- 23.020.30
- CCS
- C333
- 发布
- 2020-12-18
- 实施
- 2020-12-31
Gaseous hydrogen - Cylinders and tubes for stationary storage
- ICS
- 23.020.30
- CCS
- 发布
- 2020-12-15
- 实施
- 2020-12-15
Provisions for the installation of stationary pressure vessels for the storage of gases
- ICS
- 23.020.30
- CCS
- 发布
- 2020-12-15
- 实施
- 2020-12-15
Cylinder management specification for liquefied petroleum gas cylinder filling unit
- ICS
- 23.020.30
- CCS
- J 74
- 发布
- 2020-12-04
- 实施
- 2020-12-04
LPG equipment and accessories - Static welded steel cylindrical pressure vessels, serially produced for the storage of Liquefied Petroleum Gas (LPG) having a volume not greater than 13 m3 - Design and manufacture
- ICS
- 23.020.30
- CCS
- 发布
- 2020-12-01
- 实施
- 2020-12-01
本文件规定了液化石油气钢瓶焚烧检验工艺及安全评定技术要求。 本文件适用于公称工作压力不超过2.1MPa，公称水容积不大于150L，贮存介质为液化石油气，工作温度不低于- 40 ℃且不高于60 ℃的可重复充装钢瓶。 开展液化石油气钢瓶检验焚烧实验对比，设置不同焚烧参数（温度、时间、焚烧方式、残液浓度）时，焚烧对钢瓶材质的组织和性能及安全性的影响得出相关实验数据并完成液化石油气钢瓶焚烧推荐参数表。并在大量实验数据的基础上制定一套关于焚烧工艺安全评价方法。
Liquefied Petroleum Gas Cylinder Incineration Inspection and Safety Assessment
- ICS
- 23.020.30
- CCS
- M745
- 发布
- 2020-12-01
- 实施
- 2022-03-18
LPG equipment and accessories - Welded steel pressure vessels for LPG road tankers - Design and manufacture
- ICS
- 23.020.30
- CCS
- 发布
- 2020-12-00
- 实施
This draft European Standard specifies requirements for the design and manufacture of static welded steel cylindrical tanks, serially produced for the storage of liquefied petroleum gas (LPG) with a volume not greater than 13 m3 and for installation above or below ground. This dr
LPG equipment and accessories - Static welded steel cylindrical pressure vessels, serially produced for the storage of Liquefied Petroleum Gas (LPG) having a volume not greater than 13 m3 - Design and manufacture; German version EN 12542:2020
- ICS
- 23.020.30
- CCS
- E98
- 发布
- 2020-12-00
- 实施
Gaseous hydrogen -- Cylinders and tubes for stationary storage
- ICS
- 23.020.30
- CCS
- 发布
- 2020-11-30
- 实施
- 2020-11-30
