23.020.40 低温容器 标准查询与下载

LST EN 14197-2-2004 低温容器 静态非真空绝热容器 第2部分：设计、制造、检验和测试

Cryogenic vessels - Static non-vacuum insulated vessels - Part 2: Design, fabrication, inspection and testing

DS/EN 14197-3:2004 低温容器 静态非真空绝热容器 第3部分：操作要求

This European Standard specifies operational requirements for static non vacuum insulated vessels for cryogenic fluids according to EN 14197-1, designed for a maximum allowable pressure greater than 0,5 bar. It can be used as a guideline for vessels designed for a maximum allowable pressure of not more than 0,5 bar. The scope includes installation, putting into service, inspection, filling, maintenance and emergency procedures. This European Standard applies to vessels for cryogenic fluids as specified in EN 14197-1.

Cryogenic vessels - Static non-vacuum insulated vessels - Part 3: Operational requirements

DS/EN 13530-2/A1:2004 低温容器 大型可运输真空绝热容器 第2部分：设计、制造、检验和测试

This standard specifies requirements for the design, fabrication, inspection and testing of large transportable vacuum insulated cryogenic vessels of more than 1000 litres volume, which are permanently (fixed tanks) or not permanently (demountable tanks) attached to a vehicle, for carriage by road.

Cryogenic vessels - Large transportable vacuum insulated vessels - Part 2: Design, fabrication, inspection and testing

DIN EN 13530-2/A1:2004 低温容器.大体积、可运输、真空绝缘容器.第2部分:设计、制作、检查和试验

Inner vessel stiffening rings.

Cryogenic vessels - Large transportable vacuum insulated vessels - Part 2: Design, fabrication, inspection and testing; German version EN 13530-2:2002/A1:2004

ISO 21029-2:2004 低温容器.不超过1000升容量的可运输真空绝缘容器.第2部分:操作要求

This part of ISO 21029 specifies operational requirements for transportable vacuum insulated cryogenic vessels of not more than volume designed to operate above atmospheric pressure. Appropriate parts may be used as a guidance for a vessel design to operate open to the atmosphere. For cryogenic vessels designed for personal medical use, other requirements may apply. The scope includes putting into service, filling, withdrawal, transport within the location, storage, maintenance, periodic inspection and emergency procedures. For the transportation of these vessels by public road, rail, sea and air, other additional requirements may apply; these are defined in specific regulations. This part of ISO 21029 applies to vessels for cryogenic fluids as specified in ISO 21029-1. The additional requirements for flammable fluids are detailed in Clause 16. Transportable cryogenic vessels of not more than volume are often partly equipped by the manufacturer, but may be installed or re-installed by another party, such as the operator or owner. For this reason some of the scope of this part of ISO 21029, which includes putting into service, inspection, filling, maintenance and emergency procedure, overlaps with ISO 21029-1.

Cryogenic vessels - Transportable vacuum insulated vessels of not more than 1 000 litres volume - Part 2: Operational requirements

ISO 21010:2004 低温容器.气体/材料相容性

This International Standard specifies gas/materials compatibility requirements (such as chemical resistance) for cryogenic vessels but it does not cover mechanical properties (e.g. for low temperature applications). It gives general guidance for compatibility with gases and detailed compatibility requirements for oxygen and oxygen-enriched atmospheres. This International Standard also defines the testing methods for establishing oxygen compatibility of materials (metallic and non-metallic) to be used for cryogenic vessels and associated equipment. This International Standard focuses on materials that are normally with or could be in contact with cryogenic fluids.

Cryogenic vessels - Gas/materials compatibility

ISO 21028-2:2004 低温容器.低温下材料的韧性要求.第2部分:温度处于-80℃～-20℃

This part of ISO 21028 specifies the toughness requirements of metallic materials for use at temperatures between − 20 °C and − 80 °C to ensure their suitability for cryogenic vessels. It is applicable to fine-grain and low-alloyed steels with specified yield strength u 460 N/mm2, aluminium and aluminium alloys, copper and copper alloys and austenitic stainless steels.

Cryogenic vessels - Toughness requirements for materials at cryogenic temperature - Part 2: Temperatures between - 80 °C and - 20 °C

BS EN 14197-3:2004 低温容器.静态非真空绝缘容器.操作要求

This European Standard specifies operational requirements for static non vacuum insulated vessels for cryogenic fluids according to EN 14197-1, designed for a maximum allowable pressure greater than 0,5 bar. It can be used as a guideline for vessels designed for a maximum allowable pressure of not more than 0,5 bar. The scope includes installation, putting into service, inspection, filling, maintenance and emergency procedures. This European Standard applies to vessels for cryogenic fluids as specified in EN 14197-1.

Cryogenic vessels - Static non-vacuum insulated vessels - Operational requirements

DS/EN 14197-2:2004 低温容器 静态非真空绝热容器 第2部分：设计、制造、检验和测试

This standard specifies requirements for the design, fabrication, inspection and testing of static non-vacuum insulated cryogenic vessels designed for a maximum allowable pressure of more than 0,5 bar.

Cryogenic vessels - Static non-vacuum insulated vessels - Part 2: Design, fabrication, inspection and testing

EN 14197-3:2004 低温容器.静态非真空绝缘容器.操作要求.合并勘误表2004年8月和合并修定A1-2005

This European Standard specifies operational requirements for static non vacuum insulated vessels for cryogenic fluids according to EN 14197-1, designed for a maximum allowable pressure greater than 0,5 bar. It can be used as a guideline for vessels designed for a maximum allowable pressure of not more than 0,5 bar.The scope includes installation, putting into service, inspection, filling, maintenance and emergency procedures.This European Standard applies to vessels for cryogenic fluids as specified in EN 14197-1.

Cryogenic vessels - Static non-vacuum insulated vessels - Part 3: Operational requirements

DS/EN 14197-1:2004 低温容器 静态非真空绝热容器 第1部分：基本要求

This standard specifies the fundamental requirements for static non-vacuum insulated cryogenic vessels designed for a maximum allowable pressure greater than 0,5 bar. This standard applies to static non-vacuum insulated cryogenic vessels for fluids as specified in 3.1.

Cryogenic vessels - Static non-vacuum insulated vessels - Part 1: Fundamental requirements

DS/EN 14398-3:2004 低温容器 大型可运输非真空绝热容器 第3部分：操作要求

This standard specifies operational requirements for large transportable non vacuum insulated cryogenic vessels of more than 1000 l volume. This standard applies to vessels designed for cryogenic fluids specified in EN 14398-1.

Cryogenic vessels - Large transportable non-vacuum insulated vessels - Part 3: Operational requirements

DS/EN 14398-1:2004 低温容器 大型可运输非真空绝热容器 第1部分：基本要求

This standard specifies the fundamental requirements for large transportable non-vacuum insulated cryogenic vessels and designed to operate above atmospheric pressure. This standard applies to large transportable non-vacuum insulated cryogenic vessels for fluids as specified in 3.1 and is not applicable to such vessels designed for toxic fluids.

Cryogenic vessels - Large transportable non-vacuum insulated vessels - Part 1: Fundamental requirements

DIN EN 14398-1:2004 低温容器.大型可运输的非真空绝缘容器.第1部分:基本要求

Cryogenic vessels - Large transportable non-vacuum insulated vessels - Part 1: Fundamental requirements; German version EN 14398-1:2003

BS EN 14197-2:2003+A1:2006 低温容器.静态非真空绝缘容器.设计、制造、检验和测试

This European Standard specifies requirements for the design, fabrication, inspection and testing of static non-vacuum insulated cryogenic vessels designed for a maximum allowable pressure of more than 0,5 bar. This European standard applies to static non-vacuum insulated cryogenic vessels for fluids as specified in EN 14197-1 and does not apply to vessels designed for toxic fluids. For static non-vacuum insulated cryogenic vessels designed for a maximum allowable pressure of not more than 0,5 bar this European Standard may be used as a guide.

Cryogenic vessels - Static non-vacuum insulated vessels - Part 2: Design, fabrication, inspection and testing

DS/EN 13458-3:2003 低温容器 静态真空绝热容器 第3部分：操作要求

This standard specifies operational requirements for static vacuum insulated vessels designed for a maximum allowable pressure of more than 0,5 bar. It may also be used as a guideline for vessels designed for a maximum allowable pressure of less than 0,5 bar.

Cryogenic vessels - Static vacuum insulated vessels - Part 3: Operational requirements

DIN EN 14197-1:2003 低温容器.静压非真空绝热容器.第1部分:基本要求

Cryogenic vessels - Static non-vacuum insulated vessels - Part 1: Fundamental requirements; German version EN 14197-1:2003

LST EN 13458-2-2003 低温容器 静态真空绝热容器 第2部分：设计、制造、检验和测试

Cryogenic vessels - Static vacuum insulated vessels - Part 2: Design, fabrication, inspection and testing

BS EN 14398-3:2003 低温容器.大型可运输的非真空绝缘容器.操作要求

1 This European Standard specifies operational requirements for large transportable non vacuum insulated cryogenic vessels of more than 1000 l volume. 2 This European Standard applies to vessels designed for cryogenic fluids specified in EN 14398-1.

Cryogenic vessels - Large transportable non-vacuum insulated vessels - Operational requirements

BS EN 14398-2:2003+A2:2008 低温容器.大型可运输非真空绝缘容器.设计、制造、检验和测试

Cryogenic vessels - Large transportable non-vacuum insulated vessels - Design, fabrication, inspection and testing