23.020.40 低温容器 标准查询与下载

EN 13530-1:2002 低温容器.可运输大型真空绝热容器.第1部分:基本要求

This European Standard specifies the fundamental requirements for large transportable vacuum insulated cryogenic vessels designed to operate above atmospheric pressure. Appropriate parts can be used as a guidance for vessels designed to operate toThe atmosphere.

Cryogenic vessels - Large transportable vacuum insulated vessels - Part 1: Fundamental requirements

EN 13530-3:2002 低温容器.大体积,可运输,真空绝缘容器.第3部分:操作要求.包含修改件A1-2005

1.1 This European Standard specifies operational requirements for large transportable vacuum insulatedcryogenic vessels of more than 1000 I volume.1.2 This European Standard applies to vessels designed for cryogenic fluids specified in EN 13530-1.

Cryogenic Vessels - Large Transportable Vacuum Insulated Vessels - Part 3: Operational Requirements (Incorporates Amendment A1: 2005)

EN 13458-1:2002 冷冻容器.静态真空绝缘容器.第1部分:基本要求

This European Standard specifies the fundamental requirements for static vacuum insulated cryogenic vesselsdesigned for a maximum allowable pressure greater than 0,5 bar.This European Standard applies to static vacuum insulated cryogenic vessels for fluids as specified in 3.1.For static vacuum insulated cryogenic vessels designed for a maximum allowable pressure of not more than0,5 bar,This standard can be used as a guide.This European Standard is not applicable to vessels built on-site.

Cryogenic vessels - Static vacuum insulated vessels - Part 1: Fundamental requirements

LST EN 1251-1-2002 低温容器 容积不超过 1000 升的可运输真空绝热容器 第1部分：基本要求

Cryogenic vessels - Transportable vacuum insulated vessels of not more than 1000 litres volume - Part 1: Fundamental requirements

LST EN 1797-2002 低温容器 气体/材料兼容性

Cryogenic vessels - Gas/material compatibility

EN 13458-2:2002 冷冻容器.静态真空绝缘容器.第2部分:设计,制造,检查和试验

This European Standard specifies requirements forThe design, fabrication, inspection and testing of static vacuuminsulated cryogenic vessels designed for a maximum allowable pressure of more than 0,5 bar.This European Standard is applicable to static vacuum insulated cryogenic vessels for fluids as specified inEN 13458-1,and does not apply to vessels designed for toxic fluids.For static vacuum insulated cryogenic vessels designed for a maximum allowable pressure of not more than0,5 barThis standard can be used as a guide.

Cryogenic vessels - Static vacuum-insulated vessels - Part 2: Design, fabrication, inspection and testing

EN 13648-3:2002 低温阀.过压保护安全设备.第3部分:排量要求的测定.容积和尺寸

This standard provides a separate calculation method for determining the contributing mass flow to be relieved resulting from each of the following specified conditions

Cryogenic vessels - Safety devices for protection against excessive pressure - Part 3: Determination of required discharge - Capacity and sizing

DS/EN 1797:2001 低温容器 气体/材料兼容性

This European Standard specfies requirements for gas/materials compatibility for cryogenic vessels (such as chemical resistance) but it does not cover mechanical properties (e.g. for low temperature application). It gives guidance for compatibility with gases other than oxygen and it gives detailed requirements for oxygen and oxygen enriched atmosphere compatibility and defines the testing methods for establishing oxygen compatibility of materials (metallic and non-metallic) to be used for cryogenic vessels and associated equipment.

Cryogenic vessels - Gas/material compatibility

NF E86-505*NF EN 1797:2001 低温容器.气体/材料可容性

Cryogenic vessels - Gas/material compatibility.

NF E86-506-2:2001 低温容器.材料.第2部分:在-80℃至-20℃温度范围内的韧性要求

Cryogenic vessels - Materials - Part 2 : toughness requirements for temperatures between -80 oC and -20 oC.

DIN EN 1252-2:2001 深冷容器.材料.第2部分:温度在摄氏-80度和-20度之间的韧性要求.

The document specifies the toughness requirements of the metallic materials for use at a temperature between -80 ?et -20 ?ensuring suitability for use for the cryogenic vessels. Fine grain and low alloyed steels with specified yield strength 460 N/ aluminium and aluminium alloys, copper and copper alloys and austenitic stainless stells are covered by this standard.#,,#

Cryogenic vessels - Materials - Part 2: Toughness requirements for temperatures between -80 °C and -20 °C; German version EN 1252-2:2001

BS EN 1797:2001 低温容器.气体/材料兼容性

This European Standard specifies requirements for gas/materials compatibility for cryogenic vessels (such as chemical resistance) but it does not cover mechanical properties (e.g. for low temperature application). It gives guidance for compatibility with gases other than oxygen and it gives detailed requirements for oxygen and oxygen enriched atmosphere compatibility and defines the testing methods for establishing oxygen compatibility of materials (metallic and non-metallic) to be used for cryogenic vessels and associated equipment. It mainly deals with materials that are normally or could be in contact with liquid/gaseous oxygen e.g., materials for cryogenic vessels used for the storage and/or transport of liquid oxygen. It also deals with the materials which can be in contact with oxygen enriched environment e.g. insulating materials used for nitrogen, neon, hydrogen and helium cryogenic vessels in case of air condensation.

Cryogenic vessels - Gas/material compatibility

BS EN 1252-2:2001 低温容器.材料.温度在-80--20度的韧度要求

This European Standard specifies the toughness requirements of the metallic materials for use at a temperature between -80 ℃ and -20 ℃ ensuring suitability for use for the cryogenic vessels. Fine grain and low alloyed steels with specified yield strength ≤ 460 N/mm, aluminium and aluminium alloys, copper and copper alloys and austenitic stainless steels are covered by this standard.

Cryogenic vessels - Materials - Toughness requirements for temperatures between -80 °C and -20 °C

DS/EN 12434/AC:2001 低温容器 低温软管

This standard gives design, construction, type and production testing, and marking requirements for non insulated cryogenic flexible hose used for the transfer of cryogenic fluids within the following range of operating conditions: - working temperature: from -270°C to + 65°C; - maximum nominal pressure: 80 bar; - nominal size (DN): from 10 to 100. End fittings for mounting of any couplings are within the scope of this standard, but the couplings are subject to other standards.

Cryogenic vessels - Cryogenic flexible hoses

DS/EN 1252-2:2001 低温容器 材料 第2部分：-80°C 和 -20°C 之间温度的韧性要求

This European standard specifies the toughness requirements of the metallic materials for use at a temperature between -80°C and -20°C ensuring suitability for use for the cryogenic vessels. Fine grain and low alloyed steels with specified yield strength less or equal to 460 N/mm2, aluminium and aluminium alloys, copper and copper alloys and austenitic stainless steels are covered by this standard.

Cryogenic vessels - Materials - Part 2: Toughness requirements for temperatures between -80 °C and -20 °C

EN 1797:2001 低温容器.气体/材料可混用性

This European Standard specifies requirements for gas/materials compatibility for cryogenic vessels (such as chemical resistance) but it does not cover mechanical properties (e.g. for low temperature application). It gives guidance for compatibility with gases other than oxygen and it gives detailed requirements for oxygen andoxygen enriched atmosphere compatibility and definesThe testing methods for establishing oxygen compatibility of materials (metallic and non-metallic) to be used for cryogenic vessels and associated equipmentIt mainly deals with materials that are normally or could be in contact with liquid/gaseous oxygen e.g,materials forcryogenic vessels used forThe storage and/or transport of liquid oxygen.It also deals withThe materials which can be in contact with oxygen enriched environment e.g. insulating materialsused for nitrogen, neon, hydrogen and helium cryogenic vessels in case of air condensation.

Cryogenic vessels - Gas/material compatibility

EN 1252-2:2001 低温容器.材料.第2部分:温度低于-80℃和-20℃之间的强度要求

This European Standard species the toughness requirements of the metallic materials for use at atemperature between-80 0C and-20 0C ensuring suitability for use for the cryogenic vessels.

Cryogenic Vessels - Materials - Part 2: Toughness Requirements for Temperatures between -80 degrees C and -20 Degrees C

DS/EN 1252-1/AC:2001 低温容器 材料 第1部分：-80°C 以下温度的韧性要求

This European Standard specifies the toughness requirements of the metallic materials for use at a temperature below - 80°C to ensure their suitability for cryogenic vessels.

Cryogenic vessels - Materials - Part 1: Toughness requirements for temperatures below -80°C

DS/EN 12434:2000 低温容器 低温软管

This standard gives design, construction, type and production testing, and marking requirements for non insulated cryogenic flexible hose used for the transfer of cryogenic fluids within the following range of operating conditions: - working temperature: from -270°C to + 65°C; - maximum nominal pressure: 80 bar; - nominal size (DN): from 10 to 100. End fittings for mounting of any couplings are within the scope of this standard, but the couplings are subject to other standards.

Cryogenic vessels - Cryogenic flexible hoses

DS/EN 13275:2000 低温容器 低温服务泵

This standard specifies the minimum requirements for the design, manufacture and testing of pumps for cryogenic service (i.e. for cryogenic fluids, see EN 1251-1). This standard covers centrifugal pumps. However the principles may be applied to other types of pumps. This standard also gives guidance on the design of installations (see annex A). It does not specify requirements on operation or maintenance.

Cryogenic vessels - Pumps for cryogenic service