23.040.01 管道部件和管道综合 标准查询与下载

UNI EN 1555-5-2021 供应气体燃料的塑料管道系统 聚乙烯（PE） 第5部分：系统适用性

Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 5: Fitness for purpose of the system

LST EN 1555-5-2021 供应气体燃料的塑料管道系统 聚乙烯（PE） 第5部分：系统适用性

Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 5: Fitness for purpose of the system

LST EN 1555-1-2021 供应气体燃料的塑料管道系统 聚乙烯（PE） 第1部分：总则

Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 1: General

T/ZZB 2512-2021 电站用闸阀

本文件规定了电站用闸阀的结构形式和基本参数、基本要求、技术要求、试验方法、检验规则、标志、供货要求及质量承诺。 本文件适用于法兰和焊接端连接的铸造、锻造闸阀的设计、制造与验收，包括超（超）临界及以下参数用的各类火力发电机组用钢制闸阀，即电站用闸阀，以下简称闸阀，其参数范围为： a) PN 系列： 1) 公称压力≤80 MPa，最高工作温度≤430 ℃； 2) 工作压力≤35 MPa，最高工作温度≤625 ℃； 3) 工作压力≤8 MPa，最高工作温度≤648 ℃。 b) Class 系列： 1) 压力级别 Class 150 至 Class 4 500。

Gate valves for power station

ASTM A961/A961M-21 管道用钢法兰、锻造配件、阀门和零件的通用要求标准规范

1.1 This specification covers a group of common requirements that shall apply to steel flanges, forged fittings, valves, and parts for piping applications under any of the following individual product specifications: Title of Specification ASTM Designation Forgings, Carbon Steel, for Piping Components A105/A105M Forgings, Carbon Steel, for General-Purpose Piping A181/A181M Forged or Rolled Alloy-Steel Pipe Flanges, Forged A182/A182M Fittings, and Valves and Parts for High Temperature Service Forgings, Carbon and Low Alloy Steel, Requiring Notch A350/A350M Toughness Testing for Piping Components Forged or Rolled 8 and 9 % Nickel Alloy A522/A522M Steel Flanges, Fittings, Valves, and Parts for Low-Temperature Service Forgings, Carbon and Alloy Steel, for Pipe Flanges, A694/A694M Fittings, Valves, and Parts for High-Pressure Transmission Service Flanges, Forged, Carbon and Alloy Steel for Low A707/A707M Temperature Service Forgings, Carbon Steel, for Piping Components with A727/A727M Inherent Notch Toughness Forgings, Titanium-Stabilized Carbon Steel, for A836/A836M Glass-Lined Piping and Pressure Vessel Service 1.2 In case of conflict between a requirement of the individual product specification and a requirement of this general requirement specification, the requirements of the individual product specification shall prevail over those of this specification. 1.3 By mutual agreement between the purchaser and the supplier, additional requirements may be specified (see Section 4.1.2). The acceptance of any such additional requirements shall be dependent on negotiations with the supplier and must be included in the order as agreed upon between the purchaser and supplier. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text and the tables, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply, unless the “M” designation (SI) of the product specification is specified in the order. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Common Requirements for Steel Flanges, Forged Fittings, Valves, and Parts for Piping Applications

ASTM A888-21a 卫生和雨水排放、废物和通风管道用无轮毂铸铁污水管和配件的标准规范

1.1 This specification covers hubless cast iron soil pipe and fittings for use in gravity flow applications. It establishes standards covering material, manufacture, mechanical and chemical properties, dimensions, coating, test methods, inspection, certification, and product marking for hubless cast iron soil pipe and fittings. These pipe and fittings are intended for non-pressure applications, as the selection of the proper size for sanitary drain, waste, vent, and storm drain systems allows free air space for gravity drainage. 1.2 The EDP/ASA numbers indicated in this section represent a Uniform Industry Code adopted by the American Supply Association (ASA). A group designation prefix, 022, is assigned to hubless products, followed by the four-digit identification assigned to individual items and a check digit. This system has been instituted to facilitate EDP control through distribution channels, and is to be used universally in ordering and specifying product items. Those items with no EDP numbers are either new, special, or transitory and will be assigned numbers on subsequent prints of this specification. 1.3 This specification covers pipe and fittings of the following patterns and applies to any other patterns that conform with the dimensions found in Tables 1 and 2 and all other applicable requirements given in this specification.2 1.3.1 Lengths: Figures EDP/ASA Identification Numbers for Hubless Pipe Fig. 1 10 ft (3.0 m) in sizes and 5 ft. (1.5 m) 11⁄2, 2, 3, 4, 5, 6, 8, 10, 12, and 15 in. Fig. 1, Fig. 2 Method of Specifying Fittings Fig. 3 1.3.2 Fittings: Quarter Bend Fig. 5 Quarter Bend, Reducing Fig. 6 Quarter Bend, with Side Opening Fig. 7 Quarter Bend, with Heel Opening Fig. 8 Quarter Bend, Tapped Fig. 9 Quarter Bend, Double Fig. 10 Quarter Bend, Long Fig. 11 Short Sweep Fig. 12 Long Sweep Fig. 13 Long Sweep, Reducing Fig. 14 Fifth Bend Fig. 15 Sixth Bend Fig. 16 Eighth Bend Fig. 17 Eighth Bend, Long Fig. 18 Sixteenth Bend Fig. 19 Sanitary Tee Fig. 20 Sanitary Tee with Side Opening Fig. 21 Sanitary Tee with 2 in. Side Opening R or L/R and L Fig. 22 Sanitary Tee, New Orleans Special with Side Opening Fig. 23 Sanitary Tee with 45° Side Openings and New Orleans Fig. 24 Sanitary Special Tee Tapped Fig. 25 Sanitary Tapped Tee, Horizontal Twin Fig. 26 Sanitary Tapped Tee, Double Vertical Fig. 27 Y Branch Fig. 28 Y Branch, Double Fig. 29 Y Branch, Upright Fig. 30 Upright Y Wide Center Florida Special Fig. 31 Y Branch, Combination 1⁄8 Bend Fig. 32 Y Branch, Combination 1⁄8 Bend Double Fig. 33 Sanitary Cross Fig. 34 Sanitary Cross with Side Opening Fig. 35 Sanitary Cross, New Orleans, with Side Openings Fig. 36 Sanitary Cross, New Orleans, with 45° Special and Regular Side Openings Fig. 37 Sanitary Cross, Tapped Fig. 38 Test Tee Fig. 39 Tapped Extension Piece Fig. 40 Increaser-Reducer Fig. 41 Increaser-Reducer, Short Fig. 42 Tapped Adapter Fig. 43 Blind Plug Fig. 44 Iron Body Cleanout, Tapped Fig. 45 P Trap Fig. 46 P Trap, Long Fig. 47 P Trap, Deep Seal Fig. 48 P Trap, with Primer Fig. 49 P Trap, with Tapped Inlet Fig. 50 Tapped Inlet, Double Fig. 51 Modified Combination Wye and 1⁄8 Bend, Double Fig. 52 Modified Combination Wye and 1⁄8 Bend, Double, Extended Fig. 53 Two-Way Cleanout Fig. 54 Twin Cleanout Fig. 55 1 This specification is under the jurisdiction of ASTM Committee A04 on Iron Castings and is under the direct responsibility of Subcommittee A04.12 on Pipes and Tubes. Current edition approved Sept. 1, 2021. Published September 2021. Originally approved in 1990. Last previous edition approved in 2021 as A888 – 21. DOI: 10.1520/A0888-21A. 2 Reprinted with permission from Cast Iron Soil Pipe Institute (CISPI), 2401 Fieldcrest Dr., Mundelein, IL 60060, http://www.cispi.org. Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org. Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. 1 Closet Bend, Regular and Reducing Fig. 56 Closet Flange Riser Fig. 57 Tapping Bosses Fig. 58 Double Sweep Sanitary Tee (Extended) Fig. 59 Running Trap with Double Vents Fig. 60 P Trap with Tapped or Hubless Side Inlet Fig. 61 Vented Tub Wye Extended, Double Fig. 62 Vented Tub Wye Extended Offset, Left or Right Fig. 63 Vented Tub Wye Fig. 64 Double Two-Way Cleanout Fig. 65 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 The committee with jurisdiction over this standard is aware of another comparable standard published by the Cast Iron Soil Pipe Institute, CISPI 301. NOTE 1—The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications

FprEN ISO 11295:2021 用于修复管道的塑料管道系统 战略、战术和运营活动的分类和概述（ISO/FDIS 11295:2021）

Plastics piping systems used for the rehabilitation of pipelines - Classification and overview of strategic, tactical and operational activities (ISO/FDIS 11295:2021)

EN 13480-3:2017/A4:2021 金属工业管道.第3部分:设计和计算 包含修改件A4,2021

Metallic industrial piping - Part 3: Design and calculation

OENORM EN 1555-1/A-2021 供应气体燃料的塑料管道系统 聚乙烯（PE） 第1部分：总则（国家修正案）

Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 1: General (National Amendment)

PN-EN 13480-3-2017-10/A1-2021-08 E 金属工业管道 第3部分：设计与计算

Metallic industrial piping -- Part 3: Design and calculation

EN 13480-3:2017/prA5:2021 金属工业管道.第3部分:设计和计算 包含修改件prA5,2021

Metallic industrial piping - Part 3: Design and calculation

SN EN 1555-5-2021 供应气体燃料的塑料管道系统 聚乙烯（PE） 第5部分：系统适用性

Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 5: Fitness for purpose of the system

SN EN 1555-1-2021 供应气体燃料的塑料管道系统 聚乙烯（PE） 第1部分：总则

Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 1: General

OENORM EN ISO 15493/A11:2021 工业用塑料管道系统 丙烯腈-丁二烯-苯乙烯（ABS）、未增塑聚氯乙烯（PVC-U）和氯化聚氯乙烯（PVC-C） 部件和系统规范 公制系列（修正案）

Plastics piping systems for industrial applications - Acrylonitrile-butadiene-styrene (ABS), unplasticized poly(vinyl chloride) (PVC-U) and chlorinated poly(vinyl chloride) (PVC-C) - Specifications for components and the system - Metric series (Amendment)

DS/EN 1555-1:2021 供应气体燃料的塑料管道系统“聚乙烯（PE）”第1部分：总则

Plastics piping systems for the supply of gaseous fuels – Polyethylene (PE) – Part 1: General

DS/EN 1555-5:2021 供应气体燃料的塑料管道系统“聚乙烯（PE）”第5部分：系统适用性

Plastics piping systems for the supply of gaseous fuels – Polyethylene (PE) – Part 5: Fitness for purpose of the system

EN 1555-5:2021 燃气输送用塑料管系统 聚乙烯(PE) 第5部分:系统适用性

This document specifies the requirements of fitness for purpose of the polyethylene (PE) piping system in the field of the supply of gaseous fuels. It specifies the requirements for electrofusion, butt fusion and mechanical joints. It specifies the method of preparation of test piece joints, and the tests to be carried out on these joints for assessing the fitness for purpose of the system under normal and extreme conditions. It specifies the test parameters for the test methods referred to in this document. NOTE 1 This document is intended only to be used by the product manufacturer to assess the performance of components according to EN 1555-2, EN 1555-3:2021, and EN 1555-4:2021 when joined together under normal and extreme conditions in accordance with this document. It is not intended for on-site testing of pipe systems. In conjunction with Parts 1 to 4 of EN 1555, it is applicable to PE pipes, fittings, valves, their joints and to joints with components of other materials intended to be used under the following conditions: a) a maximum operating pressure, MOP, up to and including 10 bar1 at a reference temperature of 20 °C for design purposes; b) an operating temperature between − 20 °C and 40 °C. NOTE 2 For other operating temperatures between 20 °C and 40 °C, derating coefficients are defined in Annex A. EN 1555 (all parts) covers a range of maximum operating pressures and gives requirements concerning colours.

Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 5: Fitness for purpose of the system

OENORM EN ISO 15877-2:2021 冷热水装置用塑料管道系统 氯化聚（氯乙烯）（PVC-C） 第2部分：管道（ISO 15877-2:2009 + Amd.1:2010 + Amd.2:2020）（合并版）

Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 2: Pipes (ISO 15877-2:2009 + Amd.1:2010 + Amd.2:2020) (consolidated version)

GSO ISO 15876-1:2021 冷热水装置用塑料管道系统 聚丁烯 (PB) 第1部分：概述

ISO 15876-1:2017 specifies the general aspects of polybutene-1 (PB-1) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water whether or not intended for human consumption (domestic systems) and for heating systems, under design pressures and temperatures according to the class of application (see Table 1). The designation polybutene is used together with the abbreviation PB throughout this document. ISO 15876-1:2017 covers a range of service conditions (application classes) and design pressure and pipe dimension classes. Values of TD, Tmax and Tmal in excess of those in Table 1 do not apply. NOTE It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. It also specifies the test parameters for the test methods referred to in this document. In conjunction with the other parts of ISO 15876, this document is applicable to PB pipes, fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for hot and cold water installations.

Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 1: General

OENORM EN ISO 15877-5:2021 冷热水装置用塑料管道系统 氯化聚（氯乙烯）（PVC-C） 第5部分：系统适用性（ISO 15877-5:2009 + Amd.1:2010 + Amd.2:2020 ）（合并版）

Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 5: Fitness for purpose of the system (ISO 15877-5:2009 + Amd.1:2010 + Amd.2:2020) (consolidated version)