23.040.15 有色金属管 标准查询与下载

GSO ASTM B302:2009 非合金铜管的标准规格 标准尺寸

1.1 This specification establishes requirements for threadless, seamless, deoxidized copper pipe (TP) in straight lengths, in all nominal or standard pipe sizes, for piping systems that are assembled with brazed-joint pipe fittings. The pipe shall be produced from either of coppers UNS Nos. C10300 or C12200. 1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units, which are provided for information only and are not considered standard. 1.3 The following safety hazard caveat pertains only to the test methods described Section 16 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to its use.

Standard Specification for Threadless Copper Pipe, Standard Sizes

ASTM B428-09(2018) 矩形和方形铜及铜合金管扭转角的标准试验方法

4.1 The rectangular or square copper alloy tube covered by this test method may be used in applications in which control of twist is important to proper fit in final assembly and to minimize rework to bring the tube into compliance. It is recognized that the amount of twist, in degrees per increment of length, can change as a result of the weight of the product and its length during measurement. 4.2 This test method provides a procedure for measuring the twist in square and rectangular copper and copper alloy tubes as a measure of the deviation from straightness. 4.3 This test method allows the purchaser and supplier or manufacturer to inspect square and rectangular copper and copper alloy tube with a standard technique that provides acceptable twist in delivered tubes. 1.1 This test method establishes the requirements for the determination of the angle of twist in rectangular and square copper and copper alloy tube. 1.2 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Angle of Twist in Rectangular and Square Copper and Copper Alloy Tube

NF A51-127:2008 铜和铜合金.医用气体或真空用的无缝圆铜管

Copper and copper alloys - Seamless, round copper tubes for medical gases or vacuum.

LST EN 13348-2008 铜和铜合金 医用气体或真空用无缝圆铜管

Copper and copper alloys - Seamless, round copper tubes for medical gases or vacuum

DIN EN 13348:2008 铜和铜合金.医用气体或真空用无缝圆形铜管

This European Standard specifies the requirements, sampling, test methods and conditions of delivery for copper tubes. It is applicable to seamless round copper tubes having an outside diameter from 6 mm up to and including 133 mm for pipeline systems under vacuum or for distributing the following medical gases intended to be used at operating pressures up to 2 OOO kPa: oxygen, nitrous oxide, nitrogen, helium, carbon dioxide, xenon; -- medical air: -- specific mixtures of these above mentioned gases; -- air for driving surgical tools; -- anaesthetic gases and vapours.

Copper and copper alloys - Seamless, round copper tubes for medical gases or vacuum; German version EN 13348:2008

ASTM B111/B111M-08a 铜和铜合金无缝冷凝器管和套圈的标准规范

1.1 This specification establishes the requirements for seamless tube and ferrule stock of copper and various copper alloys up to 31/8 in. [80 mm] inclusive, in diameter, for use in surface condensers, evaporators, and heat exchangers. The following coppers and copper alloys are specified: (Warning—Mercury is a definite health hazard in use and disposal. (See 12.1.)) Copper or Copper Alloy UNS No. Previously Used Designation Description C10100OFEOxygen-free electronic C10200OFAOxygen-free without residual deoxidants C10300. . .Oxygen-free, extra low phosphorus C10800. . .Oxygen-free, low phosphorus C12000DLPAPhosphorized, low residual phosphorus C12200DHPAPhosphorized, high residual phosphorus C14200DPAAPhosphorized, arsenical C19200. . .Phosphorized, 1 % iron C23000. . .Red Brass C28000. . .Muntz Metal C44300. . .Admiralty Metals, B, C, and D C44400 C44500 C60800 . . . Aluminum Bronze C61300. . .. . . C61400. . .Aluminum Bronze, D C68700. . .Aluminum Brass, B C70400. . .95-5 Copper-Nickel C70600. . .90-10 Copper-Nickel

Standard Specification for Copper and Copper-Alloy Seamless Condenser Tubes and Ferrule Stock

GOST R 52922-2008 毛细管与铜管焊接用铜制与铜合金制配件.规范

Fittings from copper and copper alloys for capillary soldering to copper tubes. Specifications

GOST R 52948-2008 铜管应用具有压缩头的铜和铜合金配件.说明书

Fittings from copper and copper alloys with compression ends for use with copper tubes. Specifications

ASTM B111/B111M-08 铜和铜合金无缝冷凝器管和套圈的标准规范

1.1 This specification establishes the requirements for seamless tube and ferrule stock of copper and various copper alloys up to 31/8 in. [80 mm] inclusive, in diameter, for use in surface condensers, evaporators, and heat exchangers. The following coppers and copper alloys are specified: (Warning—Mercury is a definite health hazard in use and disposal. (See 12.1.)) Copper or Copper Alloy UNS No. Previously Used Designation Description C10100OFEOxygen-free electronic C10200OFAOxygen-free without residual deoxidants C10300. . .Oxygen-free, extra low phosphorus C10800. . .Oxygen-free, low phosphorus C12000DLPAPhosphorized, low residual phosphorus C12200DHPAPhosphorized, high residual phosphorus C14200DPAAPhosphorized, arsenical C19200. . .Phosphorized, 1 % iron C23000. . .Red Brass C28000. . .Muntz Metal C44300. . .Admiralty Metals, B, C, and D C44400 C44500 C60800 . . . Aluminum Bronze C61300. . .. . . C61400. . .Aluminum Bronze, D C68700. . .Aluminum Brass, B C70400. . .95-5 Copper-Nickel C70600. . .90-10 Copper-Nickel

Standard Specification for Copper and Copper-Alloy Seamless Condenser Tubes and Ferrule Stock

GOST R 52949-2008 管道连接用铜制与铜合金制配件-适配器.规范

Fittings-adapters from copper and copper alloys for connecting the pipelines. Specifications

KS F 4523-2007 瓷釉园管道

이 규격은 주로 연소 기기의 배기에 사용하는 법랑 원통(이하 원통이라 한다.)에 대하여 규

Porcelain enameled exhaust pipes

NF A51-120:2006 铜和铜合金.卫生和加热设备用水和气体的圆形无缝铜管

Copper and copper alloys - Seamless, round copper tubes for water and gas in sanitary and heating applications.

BS EN 1057:2006+A1:2010 铜和铜合金制品.卫生设备和水加热器的水和气体用无缝圆铜管

This European Standard specifies the requirements, sampling, test methods and conditions of delivery for seamless round copper tubes. It is applicable to tubes having an outside diameter from 6 mm up to and including 267 mm for:  distributing networks for hot water and cold water;  hot water heating systems, including panel heating systems (under-floor, wall, overhead);  domestic gas and liquid fuel distribution;  waste water sanitation. It is also applicable to seamless round copper tubes intended to be pre-insulated before use for any of the above purposes.

Copper and copper alloys - Seamless, round copper tubes for water and gas in sanitary and heating applications

EN 1057:2006 铜和铜合金制品.卫生设备和水加热器的水和气体用无缝圆铜管.包含修改件A1-2010

This European Standard specifies the requirements, sampling, test methods and conditions of delivery for seam-less round copper tubes. It is applicable to tubes having an outside diameter from 6 mm up to and including 267 mm for:distributing networks for hot water and cold water; hot water heating systems, including panel heating systems (under-floor, wall, overhead); domestic gas and liquid fuel distribution; waste water sanitation. It is also applicable to seamless round copper tubes intended to be pre-insulated before use for any of the above purposes.

Copper and copper alloys - Seamless, round copper tubes for water and gas in sanitary and heating applications (Incorporates Amendment A1: 2010)

DIN 85004-2:2006 铜-镍合金管.第2部分:设计、制造和试验基本原则

This standard is applicalbe to the construction, production and test of pipelines of the copper-nickel-alloy CuNi10Fe1,6Mn accordcing to the material performance sheet WL 2.1972 for ships and floating devices; for other components of this material (for example welding construction of pipes, profiles and metal sheets) this standard applies correspondigly.#,,#

Pipelines of copper-nickel-alloys - Part 2: Basic principles for design and fabrication, testing

ASTM B722-06(2011) 镍铬钼钴钨铁硅合金(UNS N06333)无缝管的标准规格

1.1 This specification covers alloy N06333 in the form of hot-finished and cold-finished seamless pipe and tube intended for heat-resisting applications and general corrosive service. The general requirements for pipe and tube are covered in Specification B829. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Standard Specification for Nickel-Chromium-Molybdenum-Cobalt-Tungsten-Iron-Silicon Alloy (UNS N06333) Seamless Pipe and Tube

GOST 617-2006 铜管.技术条件

General-purpose copper and brass tubes of round section. Specifications

GOST 10092-2006 热交换器用白铜管.技术条件

Cupro-nickel tubes for heat-exchange apparatus. Specifications

NF A51-126-2/A1:2005 铜和铜合金.空气调节和制冷用无缝圆铜管.第2部分:设备用管

Copper and copper alloys - Seamless, round copper tubes for air conditioning and refrigeration - Part 2 : tubes for equipment.

NF A51-126-1/A1:2005 铜和铜合金.空气调节和制冷用无缝圆铜管.第1部分:管路系统用管

Copper and copper alloys - Seamless, round copper tubes for air conditioning and refrigeration - Part 1 : tubes for piping systems.