23.040.15 有色金属管 标准查询与下载

ANSI/ASTM B626:2001 焊接镍和镍钴合金管规范

This specification covers welded tubes made from the nickel and nickel-cobalt alloys (UNS N10001, UNS N10242, UNS N10665, UNS N12160, UNS N10629, UNS N10624, UNS N10675, UNS N10276, UNS N06455, UNS N06007, UNS N06975, UNS N08320, UNS N06985, UNS N06002, UNS N06022, UNS N06030, UNS N06058, UNS N06059, UNS N06200, UNS N06210, UNS N08031, UNS R30556, UNS N06230, UNS N06686, and UNS R20033) listed in Table 1 intended for heat exchanger and condenser tubes and tubes for general corrosive service for heat-resisting applications. This specification covers tube 1/8 to 3/in. (3.2 to 88.9 mm) in outside diameter and 0.015 to 0.148 in. (0.41 to 3.7 mm) inclusive, in wall thickness. The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

Specification for Welded Nickel and Nickel-Cobalt Alloy Tube

JIS G 7214:2000 无缝镍或镍合金管

1.1この規格は，次の寸法範囲で使用されるコンデンサ管・熱交換器管及び一般配管気断面が丸形の継目無ニッケル合金管に関する要求事項を規定する。

Seamless nickel and nickel alloy tube

ANSI/ASTM B619:2000 焊接用镍和镍钴合金管规范

This specification covers welded pipe of nickel and nickel-cobalt alloys (UNS N10001; UNS N10665; UNS N12160; UNS N10629; UNS N10675; UNS 10276; UNS N06455; UNS N06007; UNS N06975; UNS N08320; UNS N06002; UNS N06022; UNS N06059; UNS N06985; UNS N06030; UNS R30556; UNS N08031; UNS N06230; UNS N06686; and UNS R20033) as shown in Table 1. This specification covers pipe in Schedules 5S, 10S, 40S, and 80S through 8-in. nominal pipe size as set forth in ANSI B36.19 (see Table 2). Two classes of pipe are covered as follows: Class I -As welded and solution annealed or welded and sized and solution annealed. Class II -Welded, cold worked, and solution annealed. All pipe shall be furnished in the solution annealed and descaled condition. When atmosphere control is used, descaling is not necessary. The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

Specification for Welded Nickel and Nickel-Cobalt Alloy Pipe

ANSI/ASTM B622:2000 无缝镍和镍钴合金管规范

This specification covers seamless pipe and tube of nickel and nickel-cobalt alloys (UNS N10001, UNS N10665, UNS N12160, UNS N10675, UNS N10276, UNS N06455, UNS N06007, UNS N08320, UNS N06975, UNS N06002, UNS N06985, UNS N06022, UNS N08135, UNS N06255, UNS N06059, UNS N06030, UNS N08031, UNS R30556, UNSN08535, UNSN06250, UNS N06060, UNS N06230, UNS N06686, UNS N10629, and UNS R20033) as shown in Table 1. Pipe and tube shall be supplied in the solution annealed and descaled condition. When atmosphere control is used, descaling is not necessary. The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

Specification for Seamless Nickel and Nickel-Cobalt Alloy Pipe and Tube

ASTM B829-99 镍和镍合金无缝管和管的一般要求的标准规范

1.1 This specification contains various requirements that, with the exception of Sections 5 and 10, are mandatory requirements to the following ASTM nickel and nickel alloy, seamless pipe and tube specifications: Title of Specification ASTM Designation 2 Nickel Seamless Pipe and Tube B 161 Seamless Nickel and Nickel Alloy, Condenser and B 163 Heat Exchanger Tubes Nickel-Copper Alloy (UNS N04400) Seamless Pipe and Tube B 165 Nickel-Chromium-Iron Alloys (UNS N06600, N06601, and B 167 N06690) Seamless Pipe and Tube Nickel-Iron-Chromium Alloy Seamless Pipe and Tube B 407 Nickel-Iron-Chromium-Molybdenum-Copper Alloy (UNS B 423 N08825 and N08221) Seamless Pipe and Tube Nickel-Chromium-Molybdenum-Columbium Alloys (UNS B 444 N06625) Pipe and Tube Nickel-Chromium-Iron-Columbium-Molybdenum-Tungsten B 445 Alloy (UNS N06102) Seamless Pipe and Tube Nickel-Iron-Chromium-Silicon Alloys (UNS N08330 and B 535 UNS N08332) Seamless Pipe Copper-Beryllium Alloy Forgings and Extrusion B 570 3 Seamless Nickel and Nickel-Cobalt Alloy Pipe and B 622 Tube UNS N08028 Seamless Tubes B 668 UNS N08904, UNS N08925 and UNS N08926 Seamless Pipe B 677 and Tube Iron-Nickel-Chromium-Molybdenum Alloys (UNS N08366 B 690 and UNS N08367) Seamless Pipe and Tube Ni-Cr-Mo-Co-W-Fe-Si Alloy (UNS N06333) Seamless Pipe B 722 and Tube Seamless UNS N08020, UNS N08026, and UNS N08024 B 729 Nickel-Alloy Pipe and Tube 1.2 One or more of the test requirements of Section 5 apply only if specifically stated in the product specification or in the purchase order. 1.3 In case of conflict between a requirement of the product specification and a requirement of this general specification, only the requirement of the product specification needs to be satisfied. 1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.5 The following safety hazards caveat pertains only to the test requirements portion, Section 5, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for General Requirements for Nickel and Nickel Alloys Seamless Pipe and Tube

ANSI/ASTM B829:1999 镍和镍合金无缝管一般要求规范

This specification contains various requirements that, with the exception of Sections 5 and 10, are mandatory requirements to the following ASTM nickel and nickel alloy, seamless pipe and tube specifications: Title of Specification ASTM Designation 2 Nickel Seamless Pipe and Tube B 161 Seamless Nickel and Nickel Alloy, Condenser and B 163 Heat Exchanger Tubes Nickel-Copper Alloy (UNS N04400) Seamless Pipe and Tube B 165 Nickel-Chromium-Iron Alloys (UNS N06600, N06601, and B 167 N06690) Seamless Pipe and Tube Nickel-Iron-Chromium Alloy Seamless Pipe and Tube B 407 Nickel-Iron-Chromium-Molybdenum-Copper Alloy (UNS B 423 N08825 and N08221) Seamless Pipe and Tube Nickel-Chromium-Molybdenum-Columbium Alloys (UNS B 444 N06625) Pipe and Tube Nickel-Chromium-Iron-Columbium-Molybdenum-Tungsten B 445 Alloy (UNS N06102) Seamless Pipe and Tube Nickel-Iron-Chromium-Silicon Alloys (UNS N08330 and B 535 UNS N08332) Seamless Pipe Copper-Beryllium Alloy Forgings and Extrusion B 570 3 Seamless Nickel and Nickel-Cobalt Alloy Pipe and B 622 Tube UNS N08028 Seamless Tubes B 668 UNS N08904, UNS N08925 and UNS N08926 Seamless Pipe B 677 and Tube Iron-Nickel-Chromium-Molybdenum Alloys (UNS N08366 B 690 and UNS N08367) Seamless Pipe and Tube Ni-Cr-Mo-Co-W-Fe-Si Alloy (UNS N06333) Seamless Pipe B 722 and Tube Seamless UNS N08020, UNS N08026, and UNS N08024 B 729 Nickel-Alloy Pipe and Tube .One or more of the test requirements of Section 5 apply only if specifically stated in the product specification or in the purchase order. In case of conflict between a requirement of the product specification and a requirement of this general specification, only the requirement of the product specification needs to be satisfied. The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. The following safety hazards caveat pertains only to the test requirements portion, Section 5, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Specification for General Requirements for Nickel And Nickel Alloy Seamless Pipe and Tube

ANSI/ASTM B423:1999 镍铁铬钼铜合金(UNS N08825 and UNS N08221)无缝管规范

This specification covers nickel-iron-chromium-molybdenum-copper alloys (UNS N08825 and N08221) in the form of cold-worked and hot-finished seamless pipe and tube intended for general corrosive service. The general requirements for pipe and tube are covered in Specification B829. The following precautionary caveat pertains only to the test methods portion, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Specification for Nickel-Iron-Chromium-Molybdenum-Copper Alloy (UNS N08825 and UNS N08221) Seamless Pipe and Tube

ANSI/ASTM B677:1999 UNS N08904、N08925和N08926无缝管规范

This specification covers UNS N08904, UNS N08925, and UNS N08926 seamless, cold-worked or hot-finished pipe and tube intended for general corrosive service.The values stated in inch-pound units are to be regarded as the standard.

Specification for UNS N08904, UNS N08925, and N08926 Seamless Pipe and Tube

ANSI/ASTM B546:1998 电熔焊接镍铬钶钼合金(UNS N06617)、镍铁铬硅合金(UNS N08330 and UNS N08332)、 镍铬铁合金(UNS N06025)和镍铬铁硅合金(UNS N06045)管规范

This specification covers electric fusion-welded nickel-chromium-cobalt-molybdenum alloy UNS N06617, nickel-iron-chromium-silicon alloys UNS N08330 and UNS N08332, Ni-Cr-Fe Alloy UNS N06025, and Ni-Cr-Fe-Si Alloy UNS N06045 pipe intended for heat resisting applications and general corrosive service.This specification covers pipe in sizes 3 in. (76.2 mm) nominal diameter and larger and possessing a minimum wall thickness of 0.083 in. (2.11 mm). The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

Specification for Electric-Fusion-Welded Ni-Cr-Co-Mo Alloy (UNS N06617), Ni-Fe-Cr-Si Alloys (UNS N08330 and UNS N08332), Ni-Cr-Fe Alloy (UNS N06025), and Ni-Cr-Fe-Si Alloy (UNS N06045) Pipe

ANSI/ASTM B516:1998 镍铬铁合金(UNS N06600) UNS N06025 and UNS N06045焊管规范

This specification covers welded UNS N06600 , N06025, and N06045 alloy boiler, heat exchanger, and condenser tubes for general corrosion resisting and low or high-temperature service. This specification covers tubes 1/8 to 5 in. (3.18 to 127 mm), inclusive, in outside diameter and 0.015 to 0.500 in. (0.38 to 12.70 mm), inclusive, in wall thickness. Table 2 of Specification B751 lists the dimensional requirements of these sizes. Tubes having other dimensions may be furnished provided such tubing complies with all other requirements of this specification. The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

Specification for Welded Nickel-Chromium-Iron Alloy (UNS N06600) UNS N06025 and UNS N06045 Tubes

ANSI/ASTM B517:1998 镍铬铁合金(UNS N06600) UNS N06025 and N06045焊管试验方法

This specification covers welded, cold-worked, and annealed nickel-chromium-iron alloy (UNS N06600), N06025, and N06045 pipe for general corrosive service and heat-resisting applications. This specification covers outside diameter and nominal wall pipe shown in ANSI B36.19. Pipe having other dimensions may be furnished provided such pipe complies with all other requirements of this specification. The values stated in inch-pound units are to be regarded as the standard.

Test Method for Welded Nickel-Chromium-Iron-Alloy (UNS N06600) UNS N06025 and N06045 Pipe

ASTM B745/B745M-97 用于下水道和排水管的波纹铝管标准规范

1.1 This specification covers corrugated aluminum pipe intended for use for storm water drainage, underdrains, the construction of culverts, and similar uses. Pipe covered by this specification is not normally used for the conveyance of sanitary or industrial wastes. 1.2 This specification does not include requirements for bedding, backfill, or the relationship between earth cover load and sheet thickness of the pipe. Experience has shown that the successful performance of this product depends upon the proper selection of sheet thickness, type of bedding and backfill, controlled manufacture in the plant, and care in the installation. The purchaser must correlate the above factors and also the corrosion and abrasion requirements of the field installation with the sheet thickness. The structural design of corrugated aluminum pipe and the proper installation procedures are given in Practices B790 and B788, respectively. A procedure for using life-cycle cost analysis techniques to evaluate alternative drainage system designs using corrugated metal pipe is given in Practice A930. 1.3 This specification is applicable to orders in either inch-pound units as B745 or SI units as B745M. Inch-pound units and SI units are not necessarily equivalent. SI units are shown in brackets in the text; they are the applicable values when the material is ordered to B745M.

Standard Specification for Corrugated Aluminum Pipe for Sewers and Drains

DIN 85004-9:1997 铜-镍合金管道.第9部分:透视检验总则

Pipelines of copper-nickel-alloys - Part 9: General principles for radiographic testing

ANSI/ASTM B676:1997 UNS NO8366及UNS NO8367焊管规范

This specification covers UNS N08367 welded tube for general corrosion applications. This specification covers outside diameter and nominal wall tube. The tube sizes covered by this specification are 1/8 to 5 in. (3.2 to 127 mm) in outside diameter and 0.015 to 0.320 in. (0.38 to 8.13 mm), inclusive, in wall thickness. The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

Specification for UNS N08366 and N08367 Welded Tube

NF A51-120:1996 铜和铜合金.卫生和加热设备用水和气体的圆形无缝铜管( 欧洲标准EN1057)

Copper and copper alloys. Seamless, round copper tubes for water and gas in sanitary and heating applications.

ANSI/ASTM B515:1996 UNS NO8800、UNS N08810和UNS NO8811合金焊管规范

This specification covers welded UNS N08120, UNS N08800, UNS N08810 and UNS N08811 alloy boiler, heat exchanger, and condenser tubes for general corrosion resisting and low or high-temperature service. This specification covers tubes 1/8 to 5 in. (3.18 to 127 mm), inclusive, in outside diameter and 0.015 to 0.500 in. (0.38 to 12.70 mm), inclusive, in wall thickness. Table 2 of Specification B 751 lists the dimensional requirements of these sizes. Tubes having other dimensions may be furnished provided such tubing complies with all other requirements of this specification.The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet for this product/material as provided by the manufacturer, to establish appropriate safety and heal practices, and determine the applicability of regulatory limitations prior to use.

Specification for Welded UNS N08800, UNS N08810, and UNS N08811 Alloy Tubes

ANSI/ASTM B407:1996 镍铁铬合金无缝管规范

This specification covers UNS N08120, UNS N08800, UNS N08801, UNS N08810, and UNS N08811 in the form of cold-worked and hot-finished annealed seamless pipe and tube. Alloy UNS N08800 is normally employed in service temperatures up to and including 1100?F (593?C). Alloys UNS N08120, UNS N08810, and UNS N08811 are normally employed in service temperatures above 1100?F (593?C) where resistance to creep and rupture is required, and they are annealed to develop controlled grain size for optimum properties in this temperature range.The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. The following safety hazards caveat pertains only to the test method portion, Section 13, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Specification for Nickel-Iron-Chromium Alloy Seamless Pipe and Tube

ANSI/ASTM B675:1996 UNS N08366及UNS N08367焊管规范

This specification covers UNS N08367 welded pipe for general corrosion applications. Specification B775 lists the dimensions of welded stainless steel pipe as shown in ANSI B36.19. Pipe having other dimensions may be furnished provided such pipe complies with all other requirements of this specification. The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

Specification for UNS N08366 and UNS N08367 Welded Pipe

ANSI/ASTM B834:1996 压力强化粉末冶金铁镍铬钼和镍铬钼钶(Nb)合金管法兰、管配件、阀门和零件规范

This specification covers pressure consolidated powder metallurgy iron-nickel-chromium-molybdenum (UNS N08367) and nickel-chromium-molybdenumcolumbium (Nb) (UNS N06625) pipe flanges, fittings, valves, and parts intended for general corrosion or heat-resisting service. The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. The following safety hazards caveat pertains only to test methods portions, Sections 7.3 and 13, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

Specification for Pressure Consolidated Powder Metallurgy Iron-Nickel-Chromium-Molybdenum (UNS N08367) and Nickel-Chromium-Molybdenum-Columbium (Nb) (UNS N06625) Alloy Pipe Flanges, Fittings, Valves and Parts

ASTM B111-95 铜和铜合金无缝冷凝器管和套管标准规范

Standard Specification for Copper and Copper- Alloy Seamless Condenser Tubes and Ferrule Stock