23.040.45 塑料配件 标准查询与下载

ANSI/ASTM F438:2009 套管型氯化聚氯乙烯(CPVC)塑料管配件规范,表40

Specification For Socket-type Chlorinated Poly Vinyl Chloride Cpvc Plastic Pipe Fittings, Schedule 40

ANSI/ASTM F437:2009 有螺纹的氯化聚氯乙烯(CPVC)塑料管配件规范.表80

Specification For Threaded Chlorinated Poly Vinyl Chloride Cpvc Plastic Pipe Fittings, Schedule 80

ASTM D3311-08 排水 废物和排气（DWV）塑料配件模式的标准规范

1.1 This specification provides standard fitting geometries and laying lengths for plastic fittings intended for use in drain, waste, and vent applications. (See Specifications D 2661 and D 2665.) 1.2 Fittings meeting the requirements of this standard specification are designed for use with outside diameter controlled pipe. The inside diameter can vary significantly as the wall thickness and outside diameter varies and therefore is not suitable for use as a fitting socket. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Standard Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns

SANS 51:2008 塑料管道及管道系统.注射成型热塑配件.加热影响视觉评估方法

Specifies two methods for assessing the effects of heating on injection-moulded thermoplastics pipe fittings - method A, using an air oven, and method B, using a liquid bath.

Plastics piping and ducting systems - Injection-moulded thermoplastics fittings - Methods for visually assessing the effects of heating

GSO ISO 9853:2008 用于压力管道系统的注射或成型 PVC 配件 挤压测试

This International Standard specifies a crushing test to determine the percentage deformation of injection-moulded unplasticized poly(vinyl chloride) (PVC-U) fittings and recommends a basic specification (see annex A). It applies to injection-moulded PVC-U fittings I_ for pressure pipelines, in accordance with IS0 264; - with solvent sockets, in accordance with IS0 727; - with sockets with elastomeric sealing rings, in accordance with IS0 2048.

Injection-moulded unplasticized poly(vinyl chloride) (PVC-U)fittings for pressure pipe systems -Crushing test

TIS 2357-2007 丙烯腈-丁二烯-苯乙烯(ABS)压力管

Acrylonitrile.butadiene.styrene (abs) pressure pipe

GOST R ISO 580-2008 塑料管道系统.注塑热塑性塑料配件.加热后配件外观的改变用测定方法

Plastics piping systems. Injection-moulded thermoplastics fittings. Methods for determination of fittings appearance alteration after heating

ASTM F1960-07a 交联聚乙烯用带PEX加强环的冷膨胀配件标准规范

Standard Specification for Cold Expansion Fittings with PEX Reinforcing Rings for Use with Cross-linked Polyethylene

BS ISO 4427-3:2007 塑料管道系统.给水用聚乙烯(PE)管和管件.管件

This part of ISO 4427 specifies the general aspects of fittings made from polyethylene (PE) for piping systems intended for the conveyance of water for human consumption, including raw water prior to treatment and water for general purposes. It also specifies the test parameters for the test methods to which it refers. In conjunction with the other parts of ISO 4427, it is applicable to PE fittings, their joints, to joints with components of PE and to joints with mechanical fittings of other materials, intended to be used under the following conditions: a) a maximum operating pressure (MOP) up to and including 25 bar1); b) an operating temperature of 20 °C as the reference temperature. NOTE 1 For applications operating at constant temperatures greater than 20 °C and up to 40 °C, see ISO 4427-1:2007, Annex A. NOTE 2 ISO 4427 covers a range of maximum operating pressures and gives requirements concerning colours and additives. It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national guidance or regulations and installation practices or codes. It is applicable to fittings of the following types: ⎯ fusion fittings — electrofusion fittings, butt fusion fittings and socket fusion fittings (see Annex A); ⎯ fabricated fittings (see Annex B); ⎯ mechanical fittings; ⎯ flanged fittings. 1) 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2.

Plastics piping systems - Polyethylene (PE) pipes and fittings for water supply - Fittings

ISO 4427-3:2007 塑料管道系统.给水用聚乙烯(PE)管和管件.第3部分:管件

This part of ISO 4427 specifies the general aspects of fittings made from polyethylene (PE) for piping systems intended for the conveyance of water for human consumption, including raw water prior to treatment and water for general purposes. It also specifies the test parameters for the test methods to which it refers. In conjunction with the other parts of ISO 4427, it is applicable to PE fittings, their joints, to joints with components of PE and to joints with mechanical fittings of other materials, intended to be used under the following conditions: a) a maximum operating pressure (MOP) up to and including 25 bar1); b) an operating temperature of 20 °C as the reference temperature. NOTE 1 For applications operating at constant temperatures greater than 20 °C and up to 40 °C, see ISO 4427-1:2007, Annex A. NOTE 2 ISO 4427 covers a range of maximum operating pressures and gives requirements concerning colours and additives. It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national guidance or regulations and installation practices or codes. It is applicable to fittings of the following types: ⎯ fusion fittings — electrofusion fittings, butt fusion fittings and socket fusion fittings (see Annex A); ⎯ fabricated fittings (see Annex B); ⎯ mechanical fittings; ⎯ flanged fittings. 1) 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2.

Plastics piping systems - Polyethylene (PE) pipes and fittings for water supply - Part 3: Fittings

GOST R 52779-2007 输气管道用聚乙烯管件.通用规范

Polyethylene fittings for gas pipelines. General specifications

BS 5392-1:2006 丙烯腈-丁二烯-苯乙烯共聚物(ABS)压力管用ABS配件.规范

This British Standard specifies requirements for injection moulded pipe fittings made from acrylonitrile-butadiene-styrene (ABS) polymer, for solvent welding to ABS pressure pipe conforming to BS 5391-1:2006. This British Standard is applicable, for example, to fittings intended to be used for: a) chemical plants; b) industrial sewerage engineering; c) power engineering (cooling and general-purpose water supply); d) electroplating and pickling plants; e) the semiconductor industry; f) agricultural production plants; g) water treatment; h) potable water supply; i) low temperature applications down to p40 °C. NOTE Pipe fittings conforming to this standard can be used for the transport of water intended for human consumption if it conforms to the relevant national, regional or local regulatory provisions applicable in the place of use. For products in the United Kingdom, attention is drawn to The Water Supply (Water Fittings) Regulations 1999 [1].

Acrylonitrile-butadiene-styrene (ABS) fittings for use with ABS pressure pipe - Specification

ANSI/ASTM F2261:2006 表:40～80插接式氯化聚氯乙烯（PVC）塑料管配件的标准规范

This test method covers a procedure for establishing Pressure Rating for PVC schedule 40 and 80 socket-type fittings by evaluating fitting failure test data derived by testing water-filled assemblies of pipe and fittings. Unless the data approximates a straight line, when calculated using log-log coordinates, it is not possible to assign a pressure rating to that product or sample of product. Data that exhibit high scatter, or a downward curve, due to low long term data, will give low extrapolated values that are more conservative when calculated using log-log co-ordinates. In addition, this downward curve will show as higher scatter, and where the lower confidence level limits are not met the data shall be classified as unsuitable. (See Note 1) Note 1This test method is similar to that used in Test Method D 2837, which has been used for about 30 years to establish the HDS of plastic pipe materials and is the basis for all pressure ratings assigned to plastic pipes. The products covered by this test method are schedule 40 or 80 molded PVC fittings that conform to Specifications D 2466 or D 2467. The pressure ratings developed using this test method applies only to fittings identical to the ones that were tested. Some variables that will affect the pressure rating are - pipe size, pattern, mold design, material, and molding conditions. The values in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. The testing procedure used to obtain the fitting failure data shall be as described in those sections of Test Method D 1598, that are referenced in Section of this test method. The products covered by this test method are intended for use in the distribution of pressurized liquids at 73?F. When appropriate, the design engineer must consider the effects of elevated temperature and chemical compatibility of the liquid with the fitting material and apply necessary design factors. This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the application of regulatory limitations prior to use. Note 2Pressurized (compressed) air or other compressed gases contain large amounts of stored energy which present serious safety hazards should a system fail for any reason.

Test Method for Pressure Rating Poly(vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40 and 80 Socket-type

ASTM F439-06 附表80中氯化聚氯乙烯（CPVC）塑料管配件的标准规范

1.1 This specification covers chlorinated poly(vinyl chloride) (CPVC) Schedule 80 pipe fittings. Included are requirements for materials, workmanship, dimensions, and burst pressure. Note 1The threaded CPVC fittings covered by this specification were covered previously in Specification F 437. 1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this specification. 1.3 The values stated in inch-pound units are to be regarded as the standard. The values in parentheses are given for information only. The following safety hazards caveat pertains only to the test method portion, Section , of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80

KS M ISO 2048:2005 带弹性密封圈型接头的未增塑聚氯乙烯（PVC－U）压力管的双承插接头最小啮合深度

Double-socket fittings for unplasticized poly(vinyl chloride) (PVC－U) pressure pipes with elastic sealing ring type joints－ Minimum depths of engagement

KS M ISO 9853:2005 压力管道系统用硬聚氯乙烯(PVC-U)管件.扁平试验

이 규격은 사출 성형된 무가소화 폴리염화비닐(PVC-U) 이음관의 퍼센트 변형을 측정하기

Injection-moulded unplasticized poly(vinyl chloride)(PVC-U) fittings for pressure pipe systems-Crushing test

KS M ISO 727-1:2005 压力管件用由未增塑的聚氯乙烯、氯化聚氯乙烯或丙烯腈/丁二烯/苯乙烯制的带普通管套的管配件.第1部分:米制系列

이 규격은 무가소화 폴리염화비닐(PVC-U), 염소화 폴리염화비닐(PVC-C) 또는 아크릴

Fittings made from unplasticized polyvinyl chloride(PVC－U), chlorinated polyvinyl chloride(PVC－C) or acrylonitrile/ butadiene/styrene(ABS) with plain sockets for pipes under pressure－Part 1：Metric series

KS M ISO 580:2005 塑料管和管道系统.喷射铸造热塑配件.热效应直观评估法

이 규격은 사출 성형된 무가소화 폴리염화비닐(PVC-U) 이음관의 품질을 오븐을 사용하여

Injection-moulded unplasticized polyvinyl chloride(PVC-U) fittings-Oven test-Test method and basic specifications

KS M ISO 4132:2005 承压管用硬聚氯乙烯(PVC)和金属的接头管件安装长度和螺纹尺寸.公制系列

이 규격은 사용되는 지름의 계열을 규정하고 관용 나사로써 가공된 기존의 금속관, 이음관,

Unplasticized polyvinyl chloride(PVC－U) and metal adapter fittings for pipes under pressure－Laying lengths and size of threads－Metric series

KS M ISO 4434:2005 压力管道用未增塑聚氯乙烯（PVC－U）转接件螺纹敷设长度和尺寸米制系列

Unplasticized polyvinyl chloride(PVC－U) adapter fittings for pipes under pressure－Laying length and size of threads－Metric series