23.040.45 塑料配件 标准查询与下载

KS M ISO 2045-2005 带弹性密封圈式接头的未增塑聚氯乙烯（PVC－U）和氯化聚氯乙烯（PVC－C）压力管的单套筒最小啮合深度

Single sockets for unplasticized poly(vinyl chloride)(PVC－U) and chlorinated poly(vinyl chloride)(PVC－C) pressure pipes with elastic sealing ring type joints－Minimum depths of engagement

KS M ISO 4434-2005 压力管道用未增塑聚氯乙烯（PVC－U）转接件螺纹敷设长度和尺寸米制系列

Unplasticized polyvinyl chloride(PVC－U) adapter fittings for pipes under pressure－Laying length and size of threads－Metric series

KS M ISO 4132-2005(2020) 压力管道用未增塑聚氯乙烯（PVC－U）和金属连接件螺纹敷设长度和尺寸米制系列

Unplasticized polyvinyl chloride(PVC－U) and metal adapter fittings for pipes under pressure－Laying lengths and size of threads－Metric series

KS M ISO 727-1-2005(2020) 压力管道用带普通套筒的未增塑聚氯乙烯（PVC－U）、氯化聚氯乙烯（PVC－C）或丙烯腈/丁二烯/苯乙烯（ABS）制管件第1部分:米制系列

Fittings made from unplasticized polyvinyl chloride(PVC－U), chlorinated polyvinyl chloride(PVC－C) or acrylonitrile/ butadiene/styrene(ABS) with plain sockets for pipes under pressure－Part 1：Metric ser

KS M ISO 2048-2005 带弹性密封圈型接头的未增塑聚氯乙烯（PVC－U）压力管的双承插接头最小啮合深度

Double-socket fittings for unplasticized poly(vinyl chloride) (PVC－U) pressure pipes with elastic sealing ring type joints－ Minimum depths of engagement

KS M ISO 9853-2005(2020) 压力管道系统用注塑未增塑聚氯乙烯（PVC－U）管件压碎试验

Injection-moulded unplasticized poly(vinyl chloride)(PVC－U) fittings for pressure pipe systems－Crushing test

KS M ISO 2045:2005 带弹性密封圈式接头的未增塑聚氯乙烯（PVC－U）和氯化聚氯乙烯（PVC－C）压力管的单套筒最小啮合深度

Single sockets for unplasticized poly(vinyl chloride)(PVC－U) and chlorinated poly(vinyl chloride)(PVC－C) pressure pipes with elastic sealing ring type joints－Minimum depths of engagement

BS EN ISO 580:2005 塑料管和管道系统.喷射模铸热塑性配件.热效应直观评估法

This International Standard specifies two methods for assessing the effects of heating on injection-moulded thermoplastics pipe fittings — method A, using an air oven, and method B, using a liquid bath. In case of disagreement, method A is the reference method. This International Standard is applicable to cement-welded fittings as well as to flanged fittings and fittings incorporating elastomeric seals and to fittings consisting of the assembly of several moulded parts (e.g. union connectors). It is applicable to both pressure and non-pressure fittings.

Plastics piping and ducting systems - Injection-moulded thermoplastics fittings - Methods for visually assessing the effects of heating

DS/EN ISO 580:2005 塑料管道和管道系统 注塑成型的热塑性塑料配件 目视评估加热效果的方法

This International Standard specifies two methods for assessing the effects of heating on injection-moulded thermoplastics pipe fittings — method A, using an air oven, and method B, using a liquid bath. In case of disagreement, method A is the reference method.This International Standard is applicable to cement-welded fittings as well as to flanged fittings and fittings incorporating elastomeric seals and to fittings consisting of the assembly of several moulded parts (e.g. union connectors). It is applicable to both pressure and non-pressure fittings.

Plastics piping and ducting systems – Injection-moulded thermoplastics fittings – Methods for visually assessing the effects of heating

DIN EN ISO 580:2005 塑料管和管道系统.喷射铸造热塑性配件.热效应直观评估法

This International Standard specifies two methods for assessing the effects of heating on injection-moulded thermoplastics pipe fittings. It is applicable to both pressure and non-pressure fittings and to fittings consisting of the assembly of several moulded parts.

Plastics piping and ducting systems - Injection-moulded thermoplastics fittings - Methods for visually assessing the effects of heating (ISO 580:2005); German version EN ISO 580:2005

LST EN ISO 580:2005 塑料管道和管道系统 注塑成型热塑性塑料配件 目视评估加热效果的方法（ISO 580:2005）

Plastics piping and ducting systems - Injection-moulded thermoplastics fittings - Methods for visually assessing the effects of heating (ISO 580:2005)

EN ISO 580:2005 塑料管和管道系统.喷射铸造热塑性配件.热效应直观评估法 ISO 580-2005

This International Standard specifies two methods for assessingThe effects of heating on injection-mouldedThermoplastics pipe fittings-method A, using an air oven, and method B,using a liquid bath. In case of disagreement, method A isThe reference method.

Plastics piping and ducting systems - Injection-moulded thermoplastics fittings - Methods for visually assessing the effects of heating (ISO 580:2005)

ISO 580:2005 塑料管和管道系统.喷射铸造热塑配件.热效应直观评估法

This International Standard specifies two methods for assessing the effects of heating on injection-moulded thermoplastics pipe fittings — method A, using an air oven, and method B, using a liquid bath. In case of disagreement, method A is the reference method. This International Standard is applicable to cement-welded fittings as well as to flanged fittings and fittings incorporating elastomeric seals and to fittings consisting of the assembly of several moulded parts (e.g. union connectors). It is applicable to both pressure and non-pressure fittings.

Plastics piping and ducting systems - Injection-moulded thermoplastics fittings - Methods for visually assessing the effects of heating

ASTM F1924-05(2011) 外径可控的聚乙烯配气管用塑料机械配件的标准规范

1.1 This specification describes requirements and test methods for the qualification of plastic bodied mechanical fittings for use with outside diameter controlled polyethylene (PE) gas distribution pipe, nominal 2 pipe size (IPS) and smaller complying with Specification D2513. In addition, it specifies general requirements of the material from which these fittings are made. 1.2 The test methods described in this specification are not intended to be used as routine quality control tests. 1.3 This specification covers the types of mechanical fittings described in 3.2.1. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 The following safety hazards caveat pertains only to the test method portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.6 The text of this specification references notes and footnotes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this specification.

Standard Specification for Plastic Mechanical Fittings for Use on Outside Diameter Controlled Polyethylene Gas Distribution Pipe and Tubing

ANSI/AWWA C907-2004 给水用注模聚氯乙烯4至12英寸压力管配件

This standard describes Pressure Class 150 polyvinyl chloride (PVC) injection-molded fittings with push-on rubber-gasketed joints in nominal sizes 4 in. (100 mm), to 12 in. (300 mm). The fittings are for use with PVC water distribution pipe having an outside diameter conforming to the dimensions of cast-iron pipe, and with dimension ratios (DR) of 18 (Class 150) or 25 (Class 100) as described in ANSI/AWWA C900, Standard for Polyvinyl Chloride (PVC) Pressure Pipe and Fabricated Fittings, 4 in. through 12 in., (100 mm through 300 mm) for Water Distribution.

Injection-Molded Polyvinyl Chloride (PVC) Pressure Fittings, 4 In. to 12 In. for Water Distribution

ASTM D2467-04 聚氯乙烯（PVC）塑料管件的标准规范 附表80

1.1 This specification covers poly(vinyl chloride) (PVC) Schedule 80 pipe fittings. Included are requirements for materials, workmanship, dimensions, and burst pressure. Note 18212;CPVC plastic pipe fittings, which were formerly included in this standard, are now covered in Specification F 439. 1.2 The products covered by this specification are intended for use with the distribution of pressurized liquids only, which are chemically compatible with the piping materials. Due to inherent hazards associated with testing components and systems with compressed air or other compressed gases some manufacturers do not allow pneumatic testing of their products. Consult with specific product/component manufacturers for their specific testing procedures prior to pneumatic testing.Note 28212;Pressurized (compressed) air or other compressed gases contain large amounts of stored energy which present serious saftey hazards should a system fail for any reason.1.3 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this specification.1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information only.1.5 The following safety hazards caveat pertains only to the test method portion, Section 8, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80

SANS 14236:2003 塑料管材和配件．与供水系统中的聚乙烯压力管一起使用的机械连接压合接头

Specifies the required properties and test methods for mechanical fittings intended to join polyethylene pressure pipes of nominal outside diameters not greater than 160 mm, used in water supply systems conveying potable water and water for general purpo

Plastics pipes and fittings - Mechanical-joint compression fittings for use with polyethylene pressure pipes in water supply systems

DIN 16831-6:2003 聚(异)丁烯压力管道用管道配件和连接组件.PB 125型.第6部分:耐焊接配件尺寸

This standard applies to injection-moulded resistance welding polybutene (PB) fittings as in DIN 16831-5 for resistance welding to polybutene pipes as in DIN 16968 and DIN 16969. The standard specifies the dimensions of fittings for selected pipe diameters. NOTE Any relevant European Standards shall be observed.

Pipe fittings and joint assemblies for polybutene pressure pipes - Type PB 125 - Part 6: Dimensions of fittings for resistance welding

DIN 16831-1:2003 聚(异)丁烯压力管道用管道配件和连接组件.PB 125型.第1部分:承插焊接用注模肘管尺寸

This standard applies to injection-moulded1) polybutene (PB) elbows as in DIN 16831-5 for thermo- compression socket welding to polybutene pipes as in DIN 16968 and DIN 16969. The standard specifies the dimensions of fittings for selected pipe outside diameters. NOTE Any relevant European Standards shall be observed.

Pipe fittings and joint assemblies for polybutene pressure pipes - Type PB 125 - Part 1: Dimensions of injection-moulded elbows for socket welding

DIN 16831-2:2003 聚(异)丁烯压力管道用管道配件和连接组件.PB 125型.第2部分:承插焊接用注模三通管尺寸

This standard applies to injection-moulded1) polybutene (PB) tees as in DIN 16831-5 for thermo-compression socket welding to polybutene pipes as in DIN 16968 and DIN 16969. The standard specifies the dimensions of fittings for selected pipe outside diameters. NOTE Any relevant European Standards shall be observed.

Pipe fittings and joint assemblies for polybutene pressure pipes - Type PB 125 - Part 2: Dimensios of injection-moulded tees for socket welding