塑料配件标准-分析测试百科网

DIN 16831-4:2003 聚(异)丁烯压力管道用管道配件和连接组件.PB 125型.第4部分:承插焊接用注模异径管尺寸

This standard applies to injection-moulded1) polybutene (PB) reducers as in DIN 16831-5 for thermo- compression socket welding to polybutene pipes as in DIN 16968 and DIN 16969. The standard specifies the dimensions of fittings for selected pipe outside diameters. NOTE Any relevant European Standards shall be observed.

Pipe fittings and joint assemblies for polybutene pressure pipes - Type PB 125 - Part 4: Dimensions of injection-moulded reducers for socket welding

ICS: 23.040.45
CCS: J15;G33
发布: 2003-05
实施

DIN 16832-2:2002 加压管道用氯化的聚氯乙烯管连接件和部件.PVC-C 200.第2部分:一般质量试验要求

This standard specifies test methods and general requirements for pipe joints assemblies and fittings of chlorinated polyvinyl chloride (PVC-C) according to E DIN 16832-1 for pressure pipe lines of PVC-C.

Pipe joints and components of chlorinated poly(vinyl chloride) (PVC-C) for pipes under pressure - PVC-C 200 - Part 2: General quality requirements, testing

ICS: 23.040.45
CCS: J15
发布: 2002-10
实施

DIN 16832-1:2002 聚氯乙烯承压管连接件和元件.PVC-C 200.第1部分:尺寸

Pipe joints and components of chlorinated poly(vinyl chloride) (PVC-C) for pipes under pressure - PVC-C 200 - Part 1: Dimensions

ICS: 23.040.45
CCS: J15
发布: 2002-10
实施

ANSI/ASTM D2609:2002 聚乙烯塑料管塑料插入接头规范

This specification covers plastic insert fittings for polyethylene (PE) plastic pipe. Included are requirements for materials, workmanship, dimensions, and burst pressure. The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information only. The following safety hazards caveat pertains only to the test methods portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Specification for Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe

ICS: 23.040.45
CCS: G31
发布: 2002-09-10
实施: 2002-09-10

KS M 3527-2002 再现合成树脂雪花砂箱

Reclaimed synthetic resins made for snow removing sand box

ICS: 23.040.45
CCS
发布: 2002-08-29
实施

BS ISO 727-1:2002 承压的管件用未增塑的聚氯乙烯,氯化聚氯乙烯或丙烯腈/丁二烯/苯乙烯制的带普通管套的管配件.米制系列

This part of ISO 727 specifies the dimensions of plain sockets (cylindrical and conical) in fittings made from unplasticized polyvinyl chloride) (PVC-U), chlorinated polyvinyl chloride) (PVC-C) oracrylonitrile/butadiene/styrene (ABS), intended for connecting by solvent cementing to pipes of the corresponding material for use under pressure. The resulting joint does not require mechanical anchorage. NOTE It is strongly recommended that the advice of the fittings manufacturer be sought in the selection of an appropriate type of solvent cement, depending upon whether the cylindrical or conical type of socketed fitting is being used for a particular installation.

Fittings made from unplasticized poly (vinyl chloride) (PVC-U), chlorinated poly(vinyl chloride) (PVC-C) or acrylonitrile/butadiene/styrene (ABS) with plain sockets for pipes under pressure - Metric series

ICS: 23.040.45
CCS: G32
发布: 2002-07-03
实施: 2002-07-03

ISO 7432:2002 玻璃纤维增强热固性塑料管道和管配件.检验设计带弹性体密封件的锁紧套筒连接件,包括双插孔连接件的试验方法

This International Standard specifies methods of test for joints with a locked socket and spigot, including double-socket joints, and with elastomeric seals, for buried and non-buried glass-reinforced thermosetting plastics (GRP) piping systems. This standard is applicable only to the joint, and specifies methods of test to prove its design. It assumes that the joint will be exposed to the effects of hydrostatic end thrust. The tests, detailed in 7.2 to 7.6, are applicable to locked socket-and-spigot joints intended to be used in buried or non-buried applications. With the exception of the bending test (7.5), these tests are applicable to joints with pipes and fittings of all nominal sizes. The test detailed in 7.5 is applicable to joints with pipes and fittings up to and including DN 600. The tests are suitable for evaluating joints intended for applications in which liquids are conveyed at particular temperatures specified in the referring specification.

Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods to prove the design of locked socket-and-spigot joints, including double-socket joints, with elastomeric seals

ICS: 23.040.45
CCS: G33
发布: 2002-07
实施

ISO 727-1:2002 压力管件用由未增塑的聚氯乙烯,氯化聚氯乙烯或丙烯腈/丁二烯/苯乙烯制的带普通管套的管配件.第1部分:米制系列

Fittings made from unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly(vinyl chloride) (PVC-C) or acrylonitrile/butadiene/styrene (ABS) with plain sockets for pipes under pressure - Part 1: Metric series

ICS: 23.040.45
CCS: G33
发布: 2002-05
实施

ISO 727-2:2002 压力管件用由未增塑的聚氯乙烯,氯化聚氯乙烯或丙烯腈/丁二烯/苯乙烯制的带普通管套的管配件.第2部分:英制系列

Fittings made from unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly(vinyl chloride) (PVC-C) or acrylonitrile/butadiene/styrene (ABS) with plain sockets for pipes under pressure - Part 2: Inch-based series

ICS: 23.040.45
CCS: G33
发布: 2002-05
实施

ASTM D5685-01 玻璃纤维增强热固性树脂压力管配件标准规范

1.1 This specification covers "fiberglass" (glass-fiber-reinforced thermosetting-resin) fittings for use with filament wound or centrifugally cast fiberglass pipe, or both, in sizes 1 in. through 24 in. for pipe manufactured to Specification D 2996 or D 2997, or both. 1.2 The following safety hazard caveat pertains only to the test method portion, Section 7, of this specification:1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 18212;The term "fiberglass pipe" as described in Section of this specification applies to both reinforced thermosetting resin pipe (RTRP) and reinforced polymer mortar pipe (RPMP). Note 28212;For the purposes of this standard, ploymer does not include natural polymers.Note 38212;There is no similar or equivalent ISO standard.

Standard Specification for "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe Fittings