23.040.45 塑料配件 标准查询与下载

ASTM F1960-21 交联聚乙烯（PEX）和高温聚乙烯（PE-RT）管用带PEX加强环的冷膨胀配件的标准规范

1.1?This specification covers cold expansion fittings and cross-linked (PEX) reinforcing rings for use with cross-linked polyethylene (PEX) plastic tubing in nominal tubing sizes of 3/8?, 1/2?, 5/8?, 3/4?, 1, 11/4?, 11/2?, 2, 21/2?, and 3 in. that meet the requirements of Specif

Standard Specification for Cold Expansion Fittings with PEX Reinforcing Rings for Use with Cross-linked Polyethylene (PEX) and Polyethylene of Raised Temperature (PE-RT) Tubing

ASTM F2159-21 SDR9交联聚乙烯（PEX）管和SDR9高温聚乙烯（PE-RT）管用铜压接环或替代不锈钢夹塑料插入件的标准规范

1.1?This specification establishes requirements for sulfone plastic insert fittings and copper crimp rings, or alternate stainless steel clamps for four sizes Nominal Tubing Sizes (NTS) (3/8?, 1/2?, 3/4?, and 1) of cross-linked polyethylene (PEX) tubing that meet the requirement

Standard Specification for Plastic Insert Fittings Utilizing a Copper Crimp Ring, or Alternate Stainless Steel Clamps for SDR9 Crosslinked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Tem

ASTM F2854-21 用于交联聚乙烯（PEX）管道的推入式交联聚乙烯（PEX）机械配件的标准规格

1.1 This specification covers crosslinked polyethylene (PEX) push-fit mechanical fittings for use with crosslinked polyethylene (PEX) tubing in 1⁄2, 3⁄4, 1 and 1 1⁄4 in. nominal diameters that meet the requirements of Specification F876. These fittings are intended for use in residential and commercial, hot and cold, potable water distribution systems as well as hydronic heating, including under-floor heating systems, up to and including 100 psig (6.90 bar) and 180 °F (82 °C). Included are the requirements for materials, workmanship, dimensions, performance, and markings to be used on the fittings. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Push-Fit Crosslinked Polyethylene (PEX) Mechanical Fittings for Crosslinked Polyethylene (PEX) Tubing

ASTM F2735-21 SDR9交联聚乙烯（PEX）和高温聚乙烯（PE-RT）管用塑料插入配件的标准规范

1.1 This specification establishes requirements for sulfone plastic insert fittings and copper crimp rings for three sizes (1⁄2, 3⁄4, and 1) of cross-linked polyethylene (PEX) tubing that meet the requirements for Specification F876 or F3253, and polyethylene of raised temperature (PE-RT) tubing that meet the requirements of Specification F2623. These fittings are intended for use in 100 psi (690 kPa) coldand hot-water distribution systems operating at temperatures up to and including 180 °F (82 °C). Included are the requirements for material, molded part properties, performance, workmanship, dimensions, and markings to be used on the fittings and rings. 1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following is an index of the appendix in this specification. GO/NO-GO Crimp Gauges Appendix X1 1.4 The following precautionary caveat pertains only to the test method portions, Sections 11 and 12, of this specification.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Plastic Insert Fittings For SDR9 Cross-linked Polyethylene (PEX) and Polyethylene of Raised Temperature (PE-RT) Tubing

ASTM F3348-21 SDR9交联聚乙烯（PEX）管和SDR9高温聚乙烯（PE-RT）管用带工厂装配不锈钢压套的塑料压入式配件的标准规范

Standard Specification for Plastic Press Insert Fittings with Factory Assembled Stainless Steel Press Sleeve for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature

UNI EN ISO 22391-3:2021 用于热水和冷水装置的塑料管道系统 耐高温聚乙烯（PE-RT） 第3部分：配件

Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 3: Fittings

SN EN ISO 22391-3/A1:2021 冷热水装置用塑料管道系统 耐高温聚乙烯（PE-RT） 第3部分：配件（ISO 22391-3:2009/Amd 1:2020）；修正案 A1

Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 3: Fittings (ISO 22391-3:2009/Amd 1:2020); Amendment A1

SN EN ISO 15875-3/A1:2021 冷热水装置用塑料管道系统 交联聚乙烯（PE-X） 第3部分：配件（ISO 15875-3:2003/Amd 1:2020）；修正案 A1

Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 3: Fittings (ISO 15875-3:2003/Amd 1:2020); Amendment A1

SN EN ISO 15876-3/A1:2021 用于热水和冷水装置的塑料管道系统 聚丁烯（PB） 第3部分：配件（ISO 15876-3:2017/Amd 1:2020）；修正案 A1

Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 3: Fittings (ISO 15876-3:2017/Amd 1:2020); Amendment A1

DIN EN ISO 15876-3:2021 冷热水装置用塑料管道设备. 聚丁烯(PB). 第3部分: 配件(ISO 15876-3-2017+Amd 1-2020); 德文和英文版本EN ISO 15876-3-2017+A1-2020

This Part of DIN EN ISO 15876 specifies the characteristics of fittings for polybutylene-1 (PB-1) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems)

Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 3: Fittings (ISO 15876-3:2017 + Amd 1:2020); German and English version EN ISO 15876-3:2017 + A1:2020

DIN EN ISO 22391-3:2021 冷热水装置用塑料管道系统. 耐升温的聚乙烯(PE-RT). 第3部分: 配件(ISO 22391-3-2009+Amd 1-2020); 德文和英文版本EN ISO 22391-3-2009+A1-2020

This part of DIN EN ISO 22391 specifies the characteristics of fittings for piping systems made from polyethylene of raised temperature resistance (PE-RT), Type I and polyethylene of raised temperature resistance (PE-RT), Type II intended to be used for hot and cold water install

Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 3: Fittings (ISO 22391-3:2009 + Amd 1:2020); German and English version EN ISO 22391-3:2009 + A1:2020

DIN EN ISO 15875-3:2021 冷热水装置用塑料管道设备. 交联聚乙烯(PE-X). 第3部分: 配件(ISO 15875-3-2003+Amd 1-2020); 德文和英文版本EN ISO 15875-3-2003+A1-2020

This Part of DIN EN ISO 15875 specifies the characteristics of fittings for crosslinked polyethylene (PE-X) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption, (domest

Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 3: Fittings (ISO 15875-3:2003 + Amd 1:2020); German and English version EN ISO 15875-3:2003 + A1:2020

LST EN ISO 15875-3/A1:2021 冷热水装置用塑料管道系统 交联聚乙烯（PE-X） 第3部分：配件 修正案 1（ISO 15875-3:2003/Amd 1:2020）

Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 3: Fittings - Amendment 1 (ISO 15875-3:2003/Amd 1:2020)

LST EN ISO 15876-3/A1:2021 用于热水和冷水装置的塑料管道系统 聚丁烯（PB） 第3部分：配件 修正案 1（ISO 15876-3:2017/Amd 1:2020）

Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 3: Fittings - Amendment 1 (ISO 15876-3:2017/Amd 1:2020)

LST EN ISO 22391-3/A1:2021 冷热水装置用塑料管道系统 耐高温聚乙烯（PE-RT） 第3部分：配件 修正案 1（ISO 22391-3:2009/Amd 1:2020）

Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 3: Fittings - Amendment 1 (ISO 22391-3:2009/Amd 1:2020)

UNI EN ISO 15875-3:2021 冷热水装置用塑料管道系统 交联聚乙烯（PE-X） 第3部分：配件

Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 3: Fittings

DS/EN ISO 22391-3:2021 冷热水装置用塑料管道系统 耐高温聚乙烯（PE-RT） 第3部分：管件 修正案 1（ISO 22391-3:2009/Amd 1:2020）

Plastics piping systems for hot and cold water installations – Polyethylene of raised temperature resistance (PE-RT) – Part 3: Fittings – Amendment 1 (ISO 22391-3:2009/Amd 1:2020)

DS/EN ISO 15876-3:2021 冷热水装置用塑料管道系统“聚丁烯（PB）”第3部分：管件“修正案 1（ISO 15876-3:2017/Amd 1:2020）

Plastics piping systems for hot and cold water installations – Polybutene (PB) – Part 3: Fittings – Amendment 1 (ISO 15876-3:2017/Amd 1:2020)

OENORM EN ISO 22391-3/A2:2021 冷热水装置用塑料管道系统 耐高温聚乙烯（PE-RT） 第3部分：配件（ISO 22391-3:2009/DAM 2:2020）（修正案）

Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 3: Fittings (ISO 22391-3:2009/DAM 2:2020) (Amendment)

OENORM EN ISO 21003-3/A1:2021 建筑物内热水和冷水装置的多层管道系统 第3部分：配件（ISO 21003-3:2008/DAM 1:2020）（修正案）

Multilayer piping systems for hot and cold water installations inside buildings - Part 3: Fittings (ISO 21003-3:2008/DAM 1:2020) (Amendment)