23.040.45 塑料配件 标准查询与下载

ASTM F3347-20a SDR9交联聚乙烯（PEX）管和SDR9高温聚乙烯（PE-RT）管用带工厂装配不锈钢压套的金属压入式配件的标准规范

Standard Specification for Metal Press Insert Fittings with Factory Assembled Stainless Steel Press Sleeve for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (

ASTM F3348-20a SDR9交联聚乙烯（PEX）管和SDR9高温聚乙烯（PE-RT）管用带工厂装配不锈钢压套的塑料压入式配件的标准规范

Standard Specification for Plastic Press Insert Fittings with Factory Assembled Stainless Steel Press Sleeve for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature

ASTM F3348-20 SDR9交联聚乙烯（PEX）管用带工厂组装不锈钢压套的塑料压入配件的标准规范

Standard Specification for Plastic Press Insert Fittings with Factory Assembled Stainless Steel Press Sleeve for SDR9 Cross-linked Polyethylene (PEX) Tubing

ASTM F3347-20 SDR9交联聚乙烯（PEX）管用带工厂组装不锈钢压套的金属压入配件的标准规范

Standard Specification for Metal Press Insert Fittings with Factory Assembled Stainless Steel Press Sleeve for SDR9 Cross-linked Polyethylene (PEX) Tubing

ISO 21307:2017/Amd 1:2020 塑料管和配件.聚乙烯（PE）管道系统的对接熔焊程序.修改件1

Plastics pipes and fittings — Butt fusion jointing procedures for polyethylene (PE) piping systems — Amendment 1

ASTM F2735-20 SDR9交联聚乙烯（PEX）和高温聚乙烯（PE-RT）管用塑料插入配件的标准规范

1.1 This specification establishes requirements for sulfone plastic insert fittings and copper crimp rings for three sizes (1⁄2, 3⁄4, and 1) of cross-linked polyethylene (PEX) tubing that meet the requirements for Specification F876 or F3253, and polyethylene of raised temperature (PE-RT) tubing that meet the requirements of Specification F2623. These fittings are intended for use in 100 psi (690 kPa) coldand hot-water distribution systems operating at temperatures up to and including 180 °F (82 °C). Included are the requirements for material, molded part properties, performance, workmanship, dimensions, and markings to be used on the fittings and rings. 1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following is an index of the appendix in this specification. GO/NO-GO Crimp Gauges Appendix X1 1.4 The following precautionary caveat pertains only to the test method portions, Sections 11 and 12, of this specification.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Plastic Insert Fittings For SDR9 Cross-linked Polyethylene (PEX) and Polyethylene of Raised Temperature (PE-RT) Tubing

ASTM F1960-19a 交联聚乙烯（PEX）和高温聚乙烯（PE-RT）管用带PEX加强环的冷膨胀配件的标准规范

Standard Specification for Cold Expansion Fittings with PEX Reinforcing Rings for Use with Cross-linked Polyethylene (PEX) and Polyethylene of Raised Temperature (PE-RT) Tubing

ASTM F3347-19a SDR9交联聚乙烯（PEX）管用带工厂组装不锈钢压套的金属压入配件的标准规范

Standard Specification for Metal Press Insert Fittings with Factory Assembled Stainless Steel Press Sleeve for SDR9 Cross-linked Polyethylene (PEX) Tubing

ASTM F2434-19 SDR9交联聚乙烯（PEX）管和SDR9交联聚乙烯/铝/交联聚乙烯（PEX-AL-PEX）管用铜压接环金属插入件的标准规范

1.1 This specification covers metal insert fittings with o-ring seals and copper crimp rings for use with Cross-linked Polyethylene (PEX) and Cross-linked Polyethylene/Aluminum/ Cross-linked Polyethylene (PEX-AL-PEX) tubing in 1⁄2, 3⁄4 1, and 11⁄4 in. nominal diameters that meet the requirements for Specifications F876 or F3253, and F2262 respectively. These fittings are intended for use in 125 psi (861.9 kPa) (PEX-ALPEX) and 100 psi (689.5 kPa) (PEX) coldand hot-water distribution systems operating at temperatures up to and including 180 °F (82 °C). Included are the requirements for materials, workmanship, dimensions, performance, and markings to be used on the fittings and rings. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 Compliance with this specification requires that these fittings be tested and certified to Specification F877 and F2262. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Cross-linked Polyethylene/Aluminum/Cross-linked Polyethylene (PE

ISO 4427-3:2019 塑料管道系统——给水用聚乙烯（PE）管及管件第3部分:管件

This document specifies the fittings made from polyethylene (PE) for buried or above ground applications, intended for the conveyance of water for human consumption, raw water prior to treatment, drainage and sewerage under pressure, vacuum sewer systems, and water for other purposes. NOTE 1 The intended uses include sea outfalls, laid in water and connection between pipes suspended below bridges. This document also specifies the test parameters for the test methods referred to in this document. In conjunction with the other parts of the ISO 4427 series, this document is applicable to PE fittings, to joints with components of PE or other materials, intended to be used under the following conditions: a) a maximum allowable operating pressure (PFA) up to and including 25 bar1); b) an operating temperature of 20 °C as the reference temperature. NOTE 2 For other operating temperatures, guidance is given in ISO 4427-1:2019, Annex A. This document covers a range of maximum allowable operating pressures and gives requirements concerning colours. NOTE 3 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and installation practices or codes. This document is applicable to fittings of the following types: 1. fusion fittings; a. electrofusion fittings; b. spigot end fittings (for butt fusion using heated tools and electrofusion socket fusion); c. socket fusion fittings (see Annex A); 2. mechanical fittings; a. compression fittings; b. flanged fittings; 3. fabricated fittings (see Annex B). 1) 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2. 

Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 3: Fittings

ISO 4427-1:2019 塑料管道系统——给水用聚乙烯（PE）管及管件第1部分:总则

This document specifies the general aspects of polyethylene (PE) compounds for the manufacture of pressure pipes and fittings (mains and service pipes) for buried or above ground applications, intended for the conveyance of: — water for human consumption; — raw water prior to treatment; — drainage and sewerage under pressure; — vacuum sewer systems; — water for other purposes. This document also specifies the test parameters and requirements for the test methods referred to in this document. In conjunction with other parts of the ISO 4427 series, this document is applicable to PE pipes and fittings, their joints and to joints with components made of PE and other materials, intended to be used under the following conditions: a) a maximum allowable operating pressure (PFA) up to and including 25 bar1); b) an operating temperature of 20 °C as the reference temperature. NOTE 1 For other operating temperatures, guidance is given in Annex A. concerning colours. NOTE 2 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and installation practices or codes.

Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 1: General

ISO 4427-5:2019 塑料管道系统——供水用聚乙烯（PE）管和配件第5部分:系统的适用性

This document specifies the characteristics of the fitness for purpose of pipes and/or fittings assemblies made from polyethylene (PE) for buried or above ground applications, intended for the conveyance of water for human consumption, raw water prior to treatment, drainage and sewerage under pressure, vacuum sewer systems, and water for other purposes. NOTE 1 The intended uses include sea outfalls, laid in water and pipes suspended below bridges. NOTE 2 This document is intended to be only used by the product manufacturer to assess the performance of components according to ISO 4427-2 and/or ISO 4427-3 when joined together under normal and extreme conditions. It is not intended for on-site testing of pipe systems. This document also specifies the test parameters for the test methods referred to in this document. In conjunction with the other parts of the ISO 4427 series, this document is applicable to PE pipes, fittings, their joints and to joints with components of PE and other materials, intended to be used under the following conditions: a) a maximum allowable operating pressure (PFA) up to and including 25 bar1); b) an operating temperature of 20 °C as the reference temperature. NOTE 3 For other operating temperatures, guidance is given in ISO 4427-1: 2019, Annex A. concerning colours.

Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 5: Fitness for purpose of the system

ISO 8533:2019 用于压力和非压力排水和污水的塑料管道系统 - 基于不饱和聚酯（UP）树脂的玻璃增强热固性塑料（GRP）系统 - 证明胶结或包裹接缝设计的测试方法

This document specifies methods of test for cemented or wrapped joints for buried and above ground glass-reinforced thermosetting plastics (GRP) piping systems. This document is only applicable to the joint and covers methods of test to prove its design. It assumes that the joint either is or is not intended to be subject to the effects of hydrostatic end thrust. The tests detailed in 9.2, 9.4 to 9.6 inclusive are applicable to cemented or wrapped joints intended to be used in buried or above-ground applications. The bending tests detailed in 9.3 can be used to prove the design where joints are either intended to be used in buried applications or are intended to be used in particular above-ground situations where the tests may be considered appropriate. With the exception of procedure detailed in 9.3, these test procedures are applicable to joints for pipes and fittings of all nominal sizes. The tests detailed in 9.3 are applicable to joints for pipes and fittings up to and including DN 600. The tests are applicable for evaluating joints intended for applications conveying liquids at temperatures specified in the referring standards. The test procedures in this document are damaging to the test piece, which will not be suitable for reuse after these tests. The test procedure is applied for type testing purposes only. This document is applicable only to the joint and specifies methods of test to prove its design.

Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods to prove the design of cemented or wrapped joints

ISO 8483:2019 用于压力和非压力排水和污水的塑料管道系统 - 基于不饱和聚酯（UP）树脂的玻璃增强热固性塑料（GRP）系统 - 证明螺栓法兰接头设计的测试方法

This document specifies methods of test for bolted flange joints for buried and above-ground glass- reinforced thermosetting plastics (GRP) piping systems. This document is only applicable to the joint and covers methods of test to prove its design. It assumes that the joint either is or is not intended to be subject to the effects of hydrostatic end thrust. The tests detailed in 9.2, 9.4 to 9.6 inclusive are applicable to bolted flange joints intended to be used in buried or above-ground applications. The bending tests detailed in 9.3 can be used to prove the design where joints are either intended to be used in buried applications or are intended to be used in particular above-ground situations where the tests may be considered appropriate. With the exception of the procedure detailed in 9.3, these test procedures are applicable to joints for pipes and fittings of all nominal sizes. The tests detailed in 9.3 are applicable to joints for pipes and fittings up to and including DN 600. The tests are applicable for evaluating joints intended for applications conveying liquids at temperatures specified in the referring standards. The test procedures in this document are damaging to the test piece, which will not be suitable for reuse after these tests. The test procedure is intended for type testing purposes. This document is applicable only to the joint and specifies methods of test to prove its design.

Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods to prove the design of bolted flange joints

ASTM F2159-19a SDR9交联聚乙烯（PEX）管和SDR9高温聚乙烯（PE-RT）管用铜压接环或替代不锈钢夹塑料插入件的标准规范

Standard Specification for Plastic Insert Fittings Utilizing a Copper Crimp Ring, or Alternate Stainless Steel Clamps for SDR9 Crosslinked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Tem

ASTM F439-19 附表80中氯化聚氯乙烯（CPVC）塑料管配件的标准规范

1.1 This specification covers chlorinated poly(vinyl chloride) (CPVC) Schedule 80 pipe fittings. Included are requirements for materials, workmanship, dimensions, and burst pressure. NOTE 1—The threaded CPVC fittings covered by this specification were covered previously in Specification F437. 1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this specification. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 The following safety hazards caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80

ASTM F1924-19 塑料机械配件标准规范用于外径可控聚乙烯气体分配管和管道

1.1 This specification describes requirements and test methods for the qualification of plastic bodied mechanical fittings for use with outside diameter controlled polyethylene (PE) gas distribution pipe, nominal 2 pipe size (IPS) and smaller complying with Specification D2513. In addition, it specifies general requirements of the material from which these fittings are made. 1.2 The test methods described in this specification are not intended to be used as routine quality control tests. 1.3 This specification covers the types of mechanical fittings described in 3.2. 1.4 The text of this specification references notes and footnotes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this specification. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 The following safety hazards caveat pertains only to the test method portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Plastic Mechanical Fittings for Use on Outside Diameter Controlled Polyethylene Gas Distribution Pipe and Tubing

ASTM F1960-19 交联聚乙烯（PEX）和高温聚乙烯（PE-RT）管用带PEX加强环的冷膨胀配件的标准规范

Standard Specification for Cold Expansion Fittings with PEX Reinforcing Rings for Use with Cross-linked Polyethylene (PEX) and Polyethylene of Raised Temperature (PE-RT) Tubing

ASTM D3840-19 “；玻璃纤维&x201d(非压力应用的玻璃纤维增强热固性树脂管配件

1.1 This specification covers fiberglass pipe fittings intended for use in gravity flow systems for conveying sanitary sewage, storm water, and those industrial wastes for which the fittings are determined to be suitable. Elbows, tees, laterals, crosses, reducers, and adapters are included. Both glass-fiberreinforced thermosetting-resin pipe (RTRP) and glass-fiberreinforced polymer mortar pipe (RPMP) are fiberglass pipes. NOTE 1—For the purposes of this standard, polymer does not include natural polymers. 1.2 This specification is intended to cover only dimensions, material properties, and workmanship rather than the structural design of the fittings. The structural design of the fittings shall be as agreed upon between purchaser and supplier, and needs to take into consideration the anticipated conditions of installation and service. 1.3 This specification covers only fittings fabricated from cut sections of pipe, or from a combination of pipe sections and contact molded (hand layup), or machine fabricated components. 1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information purposes only. 1.5 The following safety hazards caveat pertains only to the test method portion, Section 11, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 2—There is no known ISO equivalent to this standard. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe Fittings for Nonpressure Applications

ASTM F3348-19 SDR9交联聚乙烯（PEX）管用带工厂组装不锈钢压套的塑料压入配件的标准规范

Standard Specification for Plastic Press Insert Fittings with Factory Assembled Stainless Steel Press Sleeve for SDR9 Cross-linked Polyethylene (PEX) Tubing