23.040.45 塑料配件 标准查询与下载

ASTM F2159-19 SDR9交联聚乙烯（PEX）管和SDR9高温聚乙烯（PE-RT）管用铜压接环或替代不锈钢夹塑料插入件的标准规范

Standard Specification for Plastic Insert Fittings Utilizing a Copper Crimp Ring, or Alternate Stainless Steel Clamps for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Te

ASTM F1970-19 聚氯乙烯（PVC）或氯化聚氯乙烯（CPVC）系统用特殊工程配件、附件或阀门的标准规范

Standard Specification for Special Engineered Fittings, Appurtenances or Valves for use in Poly (Vinyl Chloride) (PVC) or Chlorinated Poly (Vinyl Chloride) (CPVC) Systems

ASTM F3348-19 SDR9交联聚乙烯（PEX）管用带工厂组装不锈钢压套的塑料压入配件的标准规范

Standard Specification for Plastic Press Insert Fittings with Factory Assembled Stainless Steel Press Sleeve for SDR9 Cross-linked Polyethylene (PEX) Tubing

ASTM F3347-19 SDR9交联聚乙烯（PEX）管用带工厂组装不锈钢压套的金属压入配件的标准规范

Standard Specification for Metal Press Insert Fittings with Factory Assembled Stainless Steel Press Sleeve for SDR9 Cross-linked Polyethylene (PEX) Tubing

ASTM D5685-19 玻璃纤维增强热固性树脂压力管配件标准规范

1.1 This specification covers “fiberglass” (glass-fiberreinforced thermosetting-resin) fittings for use with filament wound or centrifugally cast fiberglass pipe, or both, in sizes 1 in. through 24 in. for pipe manufactured to Specification D2996 or D2997, or both. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following safety hazard caveat pertains only to the test method portion, Section 7, of this specification: 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—The term “fiberglass pipe” as described in Section 3 of this specification applies to both reinforced thermosetting resin pipe (RTRP) and reinforced polymer mortar pipe (RPMP). NOTE 2—For the purposes of this standard, polymer does not include natural polymers. NOTE 3—There is no known ISO equivalent to this standard. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe Fittings

ASTM F1960-18a 交联聚乙烯（PEX）和高温聚乙烯（PE-RT）管用带PEX加强环的冷膨胀配件的标准规范

Standard Specification for Cold Expansion Fittings with PEX Reinforcing Rings for Use with Cross-linked Polyethylene (PEX) and Polyethylene of Raised Temperature (PE-RT) Tubing

ASTM F2735-18 SDR9交联聚乙烯（PEX）和高温聚乙烯（PE-RT）管用塑料插入配件的标准规范

Standard Specification for Plastic Insert Fittings For SDR9 Cross-linked Polyethylene (PEX) and Polyethylene of Raised Temperature (PE-RT) Tubing

ASTM F3347-18 SDR9交联聚乙烯（PEX）管用带工厂组装不锈钢压套的金属压入配件的标准规范

Standard Specification for Metal Press Insert Fittings with Factory Assembled Stainless Steel Press Sleeve for SDR9 Cross-linked Polyethylene (PEX) Tubing

ASTM F2159-18a SDR9交联聚乙烯（PEX）管和SDR9高温聚乙烯（PE-RT）管用铜压接环塑料插入件的标准规范

Standard Specification for Plastic Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing

ASTM F2434-18 SDR9交联聚乙烯（PEX）管和SDR9交联聚乙烯/铝/交联聚乙烯（PEX-AL-PEX）管用铜压接环金属插入件的标准规范

Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Cross-linked Polyethylene/Aluminum/Cross-linked Polyethylene (PE

ASTM F3348-18 SDR9交联聚乙烯（PEX）管用带工厂组装不锈钢压套的塑料压入配件的标准规范

Standard Specification for Plastic Press Insert Fittings with Factory Assembled Stainless Steel Press Sleeve for SDR9 Cross-linked Polyethylene (PEX) Tubing

ASTM F1960-18 交联聚乙烯（PEX）和高温聚乙烯（PE-RT）管用带PEX加强环的冷膨胀配件的标准规范

Standard Specification for Cold Expansion Fittings with PEX Reinforcing Rings for Use with Cross-linked Polyethylene (PEX) and Polyethylene of Raised Temperature (PE-RT) Tubing

ISO 10508:2006/Amd 1:2018 冷热水装置用塑料管道系统.分类和设计指南.修改件1

Plastics piping systems for hot and cold water installations — Guidance for classification and design — Amendment 1

EN ISO 15874-3:2013/A1:2018 冷热水装置用塑料管系统.聚丙烯(PP).第3部分:配件 包含修改件A1,2018

Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 3: Fittings - Amendment 1 (ISO 15874-3:2013/Amd 1:2018)

ASTM F2261-06(2018) 表40和80承插式聚氯乙烯（PVC）塑料管配件压力等级的标准试验方法

1.1 This test method covers a procedure for establishing Pressure Rating for PVC schedule 40 and 80 socket-type fittings by evaluating fitting failure test data derived by testing water-filled assemblies of pipe and fittings. 1.2 Unless the data approximates a straight line, when calculated using log-log coordinates, it is not possible to assign a pressure rating to that product or sample of product. Data that exhibit high scatter, or a downward curve, due to low long term data, will give low extrapolated values that are more conservative when calculated using log-log co-ordinates. In addition, this downward curve will show as higher scatter, and where the lower confidence level limits are not met the data shall be classified as unsuitable. (See Note 1) NOTE 1—This test method is similar to that used in Test Method D2837, which has been used for about 30 years to establish the HDS of plastic pipe materials and is the basis for all pressure ratings assigned to plastic pipes. 1.3 The products covered by this test method are schedule 40 or 80 molded PVC fittings that conform to Specifications D2466 or D2467. 1.4 The pressure ratings developed using this test method applies only to fittings identical to the ones that were tested. Some variables that will affect the pressure rating are – pipe size, pattern, mold design, material, and molding conditions. 1.5 The values in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 The testing procedure used to obtain the fitting failure data shall be as described in those sections of Test Method D1598, that are referenced in Section 6 of this test method. 1.7 The products covered by this test method are intended for use in the distribution of pressurized liquids at 73 °F. When appropriate, the design engineer must consider the effects of elevated temperature and chemical compatibility of the liquid with the fitting material and apply necessary design factors. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 2—Pressurized (compressed) air or other compressed gases contain large amounts of stored energy which present serious safety hazards should a system fail for any reason. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Pressure Rating Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40 and 80 Socket-Type.

ASTM F2159-18 SDR9交联聚乙烯（PEX）管和SDR9高温聚乙烯（PE-RT）管用铜压接环塑料插入件的标准规范

Standard Specification for Plastic Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing

ANSI/ASTM F2767:2018 用于配气外径控制的聚酰胺 12 管道和管道的电熔型聚酰胺 12 接头的标准规范

Standard Specification for Electrofusion Type Polyamide-12 Fittings for Outside Diameter Controlled Polyamide-12 Pipe and Tubing for Gas Distribution

ANSI/ASTM F2159:2018 SDR9交联聚乙烯(PEX)和SDR9高温聚乙烯(PE-RT)管用塑料插入管件的规范

Standard Specification for Plastic Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing

ASTM F2767-18 用于气体分配的用于外径可控的聚酰胺-12管和管的电熔型聚酰胺-12配件的标准规范

1.1 This specification covers polyamide12 electrofusion fittings for use with outside diameter-controlled polyamide12 pipe, covered by Specification F2785. Requirements for materials, workmanship, and testing performance are included. Where applicable in this specification “pipe” shall mean “pipe” or “tubing.” 1.2 Polyamide 12 electrofusion fittings are intended for use in polyamide 12 systems only. As per the manufacturer’s recommendations, no cross fusion between PA12, PA11 and PE is permitted. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 The following safety hazards caveat pertains only to the test method portion, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Electrofusion Type Polyamide-12 Fittings for Outside Diameter Controlled Polyamide-12 Pipe and Tubing for Gas Distribution

ISO 21225-1:2018 用于地下管网非开挖替代的塑料管道系统第1部分:通过管道爆破和管道抽取在线更换

This document specifies requirements and test methods for pipes and fittings which are part of plastics piping systems for the trenchless replacement of underground non-pressure and pressure drainage and sewerage networks and underground water and gas supply networks, by means of pipe bursting and pipe extraction. It is applicable to polyethylene (PE) pipes and fittings, as manufactured, as well as to the installed replacement system. This document is intended to be used in conjunction with standards applicable for the construction of PE pipeline systems where available. Regarding manufactured pipes it is applicable to three different PE pipe types: — PE solid wall single layered pipes (nominal outside diameter, dn), including any identification stripes; — PE pipes with co-extruded layers on either or both the outside and inside of the pipe (total outside diameter, dn), as specified in Annex A, where all layers have the same MRS rating; — PE pipes (outside diameter, dn) having a peelable, contiguous, thermoplastics additional layer on the outside of the pipe (“coated pipe”), see Annex A. In addition it is applicable to: — jointing of pipe lengths by means of butt fusion joint; — jointing of pipe lengths by means of electrofusion joint; — fabricated and injection-moulded fittings made of PE. Pipes made from other plastics, e.g. glass reinforced plastics (GRP), are outside the scope of this document.

Plastics piping systems for the trenchless replacement of underground pipeline networks — Part 1: Replacement on the line by pipe bursting and pipe extraction