23.040.45 塑料配件 标准查询与下载

ISO 21225-2:2018 用于非开挖替换地下管线网络的塑料管道系统第2部分:通过水平定向钻孔和冲击模锻在线下更换

This document specifies requirements and test methods for pipes and fittings which are part of plastics piping systems for the trenchless replacement of various underground pipeline networks, underground non-pressure and pressure drainage and sewerage networks and underground water and gas supply networks, by means of horizontal directional drilling and impact moling. It is applicable to polyethylene (PE) pipes and fittings, as manufactured, as well as to the installed replacement system. This document is intended to be used in conjunction with standards applicable for the construction of PE pipeline systems where available. Regarding manufactured pipes it is applicable to three different PE pipe types: — PE solid wall single layered pipes (nominal outside diameter, dn), including any identification stripes; — PE pipes with co-extruded layers on either or both the outside and inside of the pipe (total outside diameter, dn), as specified in Annex A, where all layers have the same MRS rating; — PE pipes (outside diameter, dn) having a peelable, contiguous, thermoplastics additional layer on the outside of the pipe (“coated pipe”), see Annex A. In addition it is applicable to: — jointing of pipe lengths by means of butt fusion joint to form continuous strings prior to installation; — fabricated and injection-moulded fittings made of PE. Pipes made from other plastics, e.g. polypropylene (PP) are outside the scope of this document. This document is not applicable to push-fit jointed discrete pipes assembled as part of the trenchless installation process.

Plastics piping systems for the trenchless replacement of underground pipeline networks — Part 2: Replacement off the line by horizontal directional drilling and impact moling

CSA B1800-2018 热塑性非压力管道概要

1 Scope 1.1 This Standard covers thermoplastic nonpressure piping, including a) drain, waste, and vent pipe and pipe fittings; b) sewer and storm pipe and pipe fittings; and c) accessories such as factory-assembled expansion joints, closet flanges, backwater valves, and cleanouts. 1.2 This Standard specifies general requirements for compounds and for manufactured pipe and pipe fittings, the relevant test methods, and marking requirements. 1.3 This Standard is intended to be used in conjunction with one of the other Standards in the CSA B181 or CSA B182 series to form a complete Standard for a particular product. 1.4 In this Standard, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the Standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the Standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.

Thermoplastic nonpressure piping compendium

ASTM F2145-13(2018) 聚酰胺11（PA 11）和聚酰胺12（PA12）用于外径可控聚酰胺11和聚酰胺12管材和管材的机械配件的标准规范

1.1 This specification describes requirements and test methods for the qualification of Polyamide 11 (PA 11) bodied mechanical fittings for use with outside diameter controlled Polyamide 11 (PA 11), nominal 2 pipe size (IPS), and smaller complying with Specification D2513. Additionally, the requirements and test methods for the qualification of Polyamide 12 (PA12) bodied mechanical fittings for use with outside diameter controlled Polyamide 11 (PA11) nominal 2 in pipe size (IPS) and smaller complying with Specification D2513 and outside diameter controlled Polyamide 12 (PA12) nominal 2 in pipe size (IPS) and smaller complying with Specification F2785. In addition, it specifies general requirements of the material from which these fittings are made. 1.2 The test methods described in this specification are not intended to be used as routine quality tests. 1.3 This specification covers the types of mechanical fittings covered in 3.2.1. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 The text of this specification references notes and footnotes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this specification. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Polyamide 11 (PA 11) and Polyamide 12 (PA12) Mechanical Fittings for Use on Outside Diameter Controlled Polyamide 11 and Polyamide 12 Pipe and Tubing

ASTM F2600-09(2018) 用于外径可控聚酰胺-11管和管的电熔型聚酰胺-11接头的标准规范

1.1 This specification covers polyamide-11 electrofusion fittings for use with outside diameter-controlled polyamide-11 pipe, covered by Specification D2513. Requirements for materials, workmanship, and testing performance are included. Where applicable in this specification “pipe” shall mean “pipe” or “tubing.” 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following safety hazards caveat pertains only to the test method portion, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Electrofusion Type Polyamide-11 Fittings for Outside Diameter Controlled Polyamide-11 Pipe and Tubing

GSO ISO 17885:2017 塑料管道系统 压力管道系统机械配件 规范

This International Standard specifies the requirements and test methods for mechanical fittings intended to join plastic pressure piping systems including transition fittings to metal pipes for the following: — supply of gaseous fuels (GAS); — supply of water for human consumption (W), including raw water prior to treatment and for the supply of water for general purpose, as well as underground drainage and sewerage under pressure (P); — supply of water for irrigation (I); — industrial applications (IS). This International Standard is applicable only to mechanical fittings with operating-temperature and pressure limits as indicated in the relevant systems standards. NOTE A list of International Standard for plastic pipes for which mechanical fittings can be used can be found in Annex A. Flanges are not covered by this International Standard. Mechanical fittings for hot and cold water systems inside buildings, as well as for district heating applications, are not covered by this International Standard.

Plastics piping systems -- Mechanical fittings for pressure piping systems -- Specifications

ASTM F438-17 套管式氯化聚氯乙烯（CPVC）塑料管件的标准规范 附表40

1.1 This specification covers chlorinated poly(vinyl chloride) (CPVC) Schedule 40 socket-type pipe fittings. Included are requirements for materials, workmanship, dimensions, and burst pressure. NOTE 1—The CPVC fittings covered by this standard were covered previously in Specification D2466. 1.2 The products covered by this specification are intended for use with the distribution of pressurized liquids only, which are chemically compatible with the piping materials. Due to inherent hazards associated with testing components and systems with compressed air or other compressed gases, some manufacturers do not allow pneumatic testing of their products. Consult with specific product/component manufacturers for their specific testing procedures prior to pneumatic testing. NOTE 2—Pressurized (compressed) air or other compressed gases contain large amounts of stored energy, which present serious safety hazards should a system fail for any reason. 1.3 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 The following safety hazards caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Socket-Type Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 40

ISO 12176-1:2017 聚乙烯系统熔接用塑料管和配件设备第1部分:对接熔接

This document specifies the general characteristics of, and performance requirements for, equipment for butt fusion jointing of polyethylene (PE) piping systems using electrically powered heater plates. It is applicable to mechanical and pressure-activated equipment for butt fusion jointing of PE pipes and fittings either intended to be used for the supply of gaseous fuels, conforming to ISO 4437-2[1] and prior to treatment) and for the conveyance of water for general purposes, conforming to ISO 4427-2[3] Butt fusion machines with an automatic controller are subject to additional requirements as given in Annex A. NOTE This document is also applicable to butt fusion machines for larger nominal pipe diameters and nominal wall thicknesses than given in this document.

Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 1: Butt fusion

ASTM F2135-01(2017) 成型排水 废料和排气（DWV）短型塑料配件的标准规范

Standard Specification for Molded Drain, Waste, and Vent (DWV) Short-Pattern Plastic Fittings

ASTM F2135-01(2017)e1 成型排水 废料和排气（DWV）短型塑料配件的标准规范

1.1 This specification covers standard fitting geometries for molded short-pattern plastic fittings intended for use in drain, waste, and vent applications. 1.2 Fittings meeting the requirements of this specification are designed for use with outside-diameter controlled pipe. The body inside diameter can vary significantly as the wall thickness and outside diameter varies, and therefore, is not suitable for use as a fitting socket. 1.3 Fittings meeting the requirements of this specification shall be tested in accordance with the applicable requirements of Specifications D2661 or D2665. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units which are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Molded Drain, Waste, and Vent (DWV) Short-Pattern Plastic Fittings

GOST R 57781-2017 玻璃钢管道及部分管道. 证明带弹性密封件的锁止插口接头(包括双插口接头)设计的试验方法

Fiberglass-reinforced thermosetting plastic pipes and parts of pipelines. Test methods to prove the design of locked socked-and-spigot joints, including double-socket joints, with elastomeric seals

DIN EN 17176-3:2017 压力导向的未增塑聚氯乙烯(PVC - O)给水、地下和地上排水、污水和灌溉用塑料管道系统. 第3部分：配件；德文和英文版本prEN 17176-3:2017

This document specifies the characteristics of solid-wall fittings made from oriented unplasticized poly(vinyl chloride) (PVC-O) for piping systems intended for water supply and for buried and above-ground drainage, sewerage, irrigation and conveyance of treated waste water under pressure. It also specifies the test parameters for the test methods referred to in this document. In conjunction with parts 1 and 5, it is applicable to oriented PVC-O fittings intended to be used for the following: a) water mains and services buried in the ground; b) conveyance of water above ground for both outside and inside buildings; c) buried and above-ground drainage, sewerage and conveyance of treated waste water under pressure; d) buried and above ground irrigation under pressure. It is applicable to piping systems intended for the supply of water under pressure up to and including 25 °C (cold water) intended for human consumption and for general purposes as well as for waste water and water for irrigation under pressure up to 25 bar. This document specifies fittings for the conveyance of water ,waste water and water for irrigation up to and including 45 °C, taking account of pressure derating factors for temperatures above 25 °C. This document specifies a range of fittings sizes and pressure classes and gives requirements concerning colours.

Plastics piping systems for water supply and for buried and above ground drainage, sewerage and irrigation under pressure - Oriented unplasticized poly(vinyl chloride) (PVC-O) - Part 3: Fittings; German and English version prEN 17176-3:2017

KS M ISO 580:2016 塑料管和管道系统 喷射铸造热塑配件 热效应直观评估法

Injection-moulded unplasticized polyvinyl chloride(PVC－U) fittings－Oven test－Test method and basic specifications

KS M ISO 580-2016(2021) 注射成型未增塑聚氯乙烯（PVC－U）配件－烘箱试验－试验方法和基本规范

Injection-moulded unplasticized polyvinyl chloride(PVC－U) fittings－Oven test－Test method and basic specifications

KS M ISO 580-2016 注塑未增塑聚氯乙烯（PVC－U）管件烘箱试验试验方法和基本规范

Injection-moulded unplasticized polyvinyl chloride(PVC－U) fittings－Oven test－Test method and basic specifications

ISO 17885:2015/Amd 1:2016 塑料管道系统.压力管道系统用机械配件.规范.修改件1

Plastics piping systems — Mechanical fittings for pressure piping systems — Specifications — Amendment 1

KS M 3410-2016 排水用未增塑聚氯乙烯（PVC-U）管件

Unplasticized poly(vinyl chloride)(PVC-U) pipe fittings for drain

GSO ISO 13957:2015 塑料管材和配件 聚乙烯螺纹轴承 抗冲击试验方法

This International Standard specifies a test method for the impact resistance of polyethylene (PE) tapping tees. This International Standard is applicable to PE tapping tees intended for the conveyance of fluids.

Plastics pipes and fittings -- Polyethylene (PE) tapping tees -- Test method for impact resistance

CAN/CSA-B1800-2015 非承压热塑性管道标准汇编

1.1 Cette norme vise les tuyaux thermoplastiques sans pression, y compris : a) les tuyaux d’évacuation et de ventilation et les raccords ; b) les tuyaux d’égout et les raccords ; et c) les accessoires assemblés en usine tels les joints de dilatation, les brides de sol de toilette, les clapets antiretour et les regards de nettoyage. 1.2 Cette norme prescrit les exigences générales visant les composés et les tuyaux et raccords manufacturés, les méthodes d’essai pertinentes et les exigences visant le marquage. 1.3 Cette norme doit être utilisée avec une des autres normes de la série CSA B181 ou CSA B182 pour former une norme complète pour un produit en particulier. 1.4 Dans cette norme, le terme «doit» indique une exigence, c’est-à-dire une prescription que l’utilisateur doit respecter pour assurer la conformité à la norme ; «devrait» indique une recommandation ou ce qu’il est conseillé mais non obligatoire de faire ; et «peut» indique une possibilité ou ce qu’il est permis de faire. Les notes qui accompagnent les articles ne comprennent pas de prescriptions ni de recommandations. Elles servent à séparer du texte les explications ou les renseignements qui ne font pas proprement partie de la norme. Les notes au bas des figures et des tableaux font partie de ceux-ci et peuvent être rédigées comme des prescriptions. Les annexes sont qualifiées de normatives (obligatoires) ou d’informatives (facultatives) pour en préciser l’application.

Compendium of standards for non-pressure thermoplastic pipes

CAN/CSA B1800-15:2015 热塑性非压力管道概要

1.1 This Standard covers thermoplastic nonpressure piping, including (a) drain, waste, and vent pipe and pipe fittings; (b) sewer and storm pipe and pipe fittings; and (c) accessories such as factory-assembled expansion joints, closet flanges, backwater valves, and cleanouts. 1.2 This Standard specifies general requirements for compounds and for manufactured pipe and pipe fittings, the relevant test methods, and marking requirements. 1.3 This Standard is intended to be used in conjunction with one of the other Standards in the CSA B181 or CSA B182 series to form a complete Standard for a particular product. 1.4 In CSA standards, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (nonmandatory) to define their application.

Thermoplastic non-pressure piping compendium

ASTM F1336-15 装衬垫的聚氯乙烯 (PVC) 污水管配件的标准规格

1.1 This specification covers requirements and test methods for fabricated or molded poly(vinyl chloride) (PVC) gasketed sewer fittings to be used with piping manufactured to Specifications D3034, F679, F891 or F1760. Fabricated fittings may be manufactured from pipe, or from a combination of pipe and injection molded parts, or from injection molded parts. 1.2 The requirements of this specification are to provide fabricated or molded PVC gasketed fittings suitable for non-pressure drainage of sewage and surface water, as well as applications involving subsurface drainage. Note 1: Industrial waste lines should be installed only with the specific approval of the governing code authority when using chemicals not commonly found in drains and sewers or temperatures in excess of 140°F (60°C), or both. 1.3 Fittings produced to this specification are intended to be installed with pipe, in accordance with Practice D2321. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 The following precautionary caveat pertains to the test method portion only, Section 10, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Poly(Vinyl Chloride) (PVC) Gasketed Sewer Fittings