23.040.50 其他材料的管和配件 标准查询与下载

BS EN 512:1995 纤维水泥制品.压力管道和接头

Specifies characteristics for pipes used to convey potable and non potable water and sewage.

Fibre-cement products - Pressure pipes and joints

BS EN 642:1995 包括接头、配件和管道预应力钢特殊要求的圆柱型和非圆柱型预应力混凝土压力管

This standard covers the requirements and the manufacture of prestressed concrete cylinder and non-cylinder pressure pipes and fittings in sizes from DN/ID 500 to DN/ID 4000 inclusive. Larger sizes could be manufactured based on the concepts of this standard. These types of pipes are designed for the internal pressure, external loads and bedding conditions designated by the purchaser.

Prestressed concrete pressure pipes, cylinder and non-cylinder, including joints, fittings and specific requirement for prestressing steel for pipes

BS EN 639:1995 包括接头和配件的混凝土压力管的共同要求

This European Standard specifies common requirements for the following components: concrete pressure pipes, joints and fittings including jacking pipes. These components are intended to be used in water systems which carry water for human consumption, industrial purposes, irrigation or waste water.

Common requirements for concrete pressure pipes including joints and fittings

EN 295-4:1995 排水管和下水道用玻璃陶管和配件及管接头.第4部分:专用配件、适配器和兼容附件用要求

This Standard specifies the requirements for special fittings, adaptors and compatible accessories made from vitrified clay and/or other suitable materials for use with vitrified clay pipes and fittings in drainage and sewerage systems. It does not apply to items which are specified in other Parts of EN 295. Any additional requirements for particular items are given in the annexes to this Part of the standard. Where this Standard provides for different systems of jointing dimensions, different lengths and different types of fittings, the specifiersípurchasers may select according to their requirements. NOTE 1. The wide diversity of ranges and numbers of special fittings, adaptors and compatible accessories offered by manufacturers and required by specifiers and purchasers throughout Europe cannot be fully listed within this standard. Manufacturers’ product range lists and specifications provide the necessary information. NOTE 2. Where reference is made to clauses in EN 295-1 : 1991 , EN 295-2 : 1991 or EN 295-3 : 1991 this is clearly stated.

Vitrified Clay Pipes and Fittings and Pipe Joints for Drains and Sewers - Part 4: Requirements for Special Fittings, Adaptors and Compatible Accessories

DIN EN 640:1994 包括管连接件和配件的分段加固(无外皮)钢筋混凝土承压管和混凝土承压管

Reinforced concrete pressure pipes and distributed reinforcement concrete pressure pipes (non-cylinder type), including joints and fittings; German version EN 640:1994

DIN EN 639:1994 包括管接头和配件的混凝土承压管通用要求

The document specifies common requirements for the following components: concrete pressure pipes, joints and fittings including jacking pipes. These components are intended to be used in water systems which carry water for human consumption, industrial purposes, irrigation or waste water.#,,#

Common requirements for concrete pressure pipes, including joints and fittings; German version EN 639:1994

DIN EN 641:1994 包括管连接件和配件带薄板套的钢筋混凝土承压管

The document specifies the requirements of concrete pressure pipe cylinder type, that is not prestressed, in sizes from DN/ID 250 to DN/ID 4000 inclusive. Pretensioned concrete cylinder pipe, in which the reinforcement is wrapped under low tension, directly on to the steel cylinder is covered by this document and is not normally manufactured in sizes above DN/ID 1400.

Reinforced concrete pressure pipes, cylinder type, including joints and fittings; German version EN 641:1994

DIN 2410-4:1994 管件.第4部分:纤维水泥管、检修孔等标准的一般评论

Pipes - Part 4: General review on standards for fibre cement pipes, manholes a.s.so.

DIN EN 512:1994 纤维混凝土制品.承压管和连接件

The document specifies the characteristics of fibre-cement pipes and joints for use under pressure for conveying potable and non potable water sewage. It is concerned with composition, classification, geometrical, mechanical and physical characteristics, acceptance tests and type tests.

Fibre-cement products - Pressure pipes and joints; German version EN 512:1994

EN 512:1994 纤维混凝土制品.承压管和连接件.包含修改件A1-2001

Fibre-Cement Products - Pressure Pipes and Joints (Incorporates Amendment A1: 2001)

CAN/CGSB-34.9-1994 石棉水泥污水管

1.1 This standard applies to asbestos-cement, nonpressure, large-diameter pipe (200 mm and up), suitable for conveying sanitary sewage to gravity-flow systems. 1.2 For cautionary notes on cutting, grinding, sanding or drilling of this product, see par. 6.2.2 and 8.3.

Asbestos-Cement Sewer Pipe

CAN/CGSB-34.1-1994 压力管道用石棉水泥管

1.1 La présente norme s'applique aux tuyaux en amiante-ciment pour canalisations pouvant transporter des fluides sous pression. 1.2 Voir l'al. 6.2.2 et le par. 8.3 pour les mises en garde concernant le coupage, le sablage, le meulage et le perçage de ce produit.

Asbestos-cement pipe for pressure pipelines

CAN/CGSB-34.22-1994 石棉水泥排水管

1.1 This standard applies to asbestos-cement drain and waste system pipe suitable for use above and below ground, inside buildings for drain, waste and vent systems and as rainwater leaders for roof drainage. This pipe is also known as asbestos-cement soil pipe. 1.2 For cautionary notes on the cutting, sanding, grinding or drilling of this product, see par. 6.2.2 and 8.3.

Asbestos-Cement Drain Pipe

CAN/CGSB-34.23-1994 石棉水泥房屋连接下水道管

1.1 This standard applies to asbestos-cement, nonpressure, small-diameter pipe, suitable for use as building sewer pipe and as building drain pipe buried under the floor. 1.2 For cautionary notes on cutting, sanding, grinding or drilling of this product, see par. 6.2.2 and 8.3.

Asbestos-Cement House Connection Sewer Pipe

CAN/CGSB-34.10-1994 通风工业用水泥

1. OBJET 1.1 La présent norme s'applique aux tuyaux et aux manchons en amiante-ciment destinés principalement aux canalisations d'évacuation des vapeurs des hottes de laboratoire et de certains procédés industriels, aux canalisations d'air traité de systèmes de ventilation ainsi qu'aux canalisations de ventilation sanitaire des réseaux d'égout. 1.2 Voir l'al. 6.2.2 et le par. 8.2 pour les mises en garde concernant le coupage, le sablage, le meulage et le perçage de ce produit. 1.3 La mise à l'essai et l'évaluation d'un produit en regard de la présente norme peuvent nécessiter l'emploi de matériaux ou d'équipement susceptibles d'être dangereux. Le présent document n'entend pas traiter de tous les aspects liés à la sécurité de son utilisation. Il appartient à l'usager de la norme de se renseigner auprès des autorités compétentes et d'adopter des pratiques d'hygiène et de sécurité conformes aux règlements en vigueur avant de l'utiliser.

Tuyau en amiante-ciment pour ventilation industrielle

SANS 921:1994 沥青浸渍的纤维管，配件和连接件

This standard specifies the dimensional and minimum quality requirements for pitch-impregnated fibre pipes (known as pitch fibre pipes) of nominal diameter 75 mm, 100 mm and 150 mm, together with pitch fibre fittings and polypropylene and polyethylene couplings, that are suitable, when they have solid walls, for use as cable conduit and when they have perforated walls, for subsoil drainage. NOTE - Assessment of compliance with the requirements of 4.11.2 for perforated pipes shall be the subject of a special agreement between the manufacturer and the purchaser.

Pitch-impregnated fibre pipes and fittings and jointing

EN 639:1994 包括管接头和配件的混凝土压力管的统一要求

This European Standard for concrete pipes is a standard which was prepared by WG 5, Concrete pipes, of the lbchnical Committee CEN/TC 164, Water supply, the Secretariat of which is held by AFNOR.

Common requirements for concrete pressure pipes including joints and fittings

EN 642:1994 包括接头,配件的圆柱型和非圆柱型预应力混凝土压力管和预应力钢管的特殊要求

This standard covers the requirements and the manufacture of prestressed concrete cylinder and non-cylinder pressure pipes and fittings in sizes from DN/ID 500 to DN/ID 4000 inclusive. Larger sizes could be manufactured based on the concepts of this standard. These types of pipes are designed for the internal pressure, external loads and bedding conditions designated by the purchaser.

Prestressed concrete pressure pipes, cylinder and non-cylinder type, including joints, fittings and specific requirement for prestressing steel for pipes

ASTM C1244M-93 负压(真空)试验测定混凝土污水管人孔的试验方法(米制)

1.1 This test method covers procedures for testing precast concrete manhole sections when using the vacuum test method to demonstrate the integrity of the installed materials and the construction procedures. This test method is used for testing concrete manhole sections utilizing mortar, mastic, or gasketed joints. 1.2 This test method is intended to be used as a preliminary test to enable the installer to demonstrate the condition of the concrete manholes prior to backfill. It may also be used to test manholes after backfilling; however, testing should be correlated with the connector supplier. 1.3 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 This test method is the companion to inch-pound Test Method C1244. Note 1-Vacuum test criteria presented in this test method are similar to those in general use. The test and criteria have been widely and successfully used in testing manholes. Note 2-It should be understood that no correlation has been found between vacuum (air) and hydrostatic tests.

Standard Test Method for Concrete Sewer Manholes by the Negative Air Pressure (Vacuum) Test (Metric)

AS 4060:1992 埋设陶土管的荷载

Specifies methods for calculating the working loads, resulting from overlaying material and superimposed dead and live loads, which act on buried vitrified clay pipelines. From these values, a design crushing load can be calculated for use in selecting a

Loads on buried vitrified clay pipes