23.040.50 其他材料的管和配件 标准查询与下载
共找到 367 条与 其他材料的管和配件 相关的标准，共 25 页
Applies to asbestos-cement, non pressure, large diameter pipe (200 mm and up), suitable for conveying sanitary sewage to gravity-flow systems
Pipe, Asbestos-Cement, Sewer
- ICS
- 23.040.50
- CCS
- 发布
- 1987-12-31
- 实施
S'applique aux tuyaux en amiante-cimente pour canalisations pouvant transporter des liquides sous pression
Asbestos-cement pipe for pressure pipelines
- ICS
- 23.040.50
- CCS
- 发布
- 1987-12-31
- 实施
Applies to asbestos-cement, nonpressure, small-diameter pipe, suitable for use as building sewer pipe and as building drain pipe buried under-floor.
Pipe, Asbestos-Cement, Sewer, House Connection
- ICS
- 23.040.50
- CCS
- 发布
- 1987-11-30
- 实施
S'applique aux tuyaux de drainage en amiante-ciment et aux tuyaux d'évacuation des eaux usées destinés à être posés sur le sol ou enfouis, à servir pour la tuyauterie à l'intérieur des bâtiments, pour les tuyauteries de vidange des eaux usées et d'aération, et aussi pour le drainage et l'évacuation des eaux de pluie du toit. Ce type de tuyau est également connu sous le nom de tuyau souterrain en amiante-ciment.
Asbestos-cement drainage pipe
- ICS
- 23.040.50
- CCS
- 发布
- 1987-08-31
- 实施
Applies to asbestos-cement pipe and couplings, intended primarily for use in exhaust conveying fumes from laboratory hoods, from certain processes, and in ventilation systems conveying treated air.
Pipe, Asbestos-Cement, Industrial Vent
- ICS
- 23.040.50
- CCS
- 发布
- 1987-08-01
- 实施
2.1 This test method provides a practical means to assess the strength of glass pipe under internal positive hydrostatic pressure. Since test pressures are twice-rated values, the test represents a stringent evaluation of product strength. 1.1 This test method covers hydrostatic pressure testing of conical end flanged pipe and fittings. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Test Method for Pressure Test on Glass Pipe
- ICS
- 23.040.50
- CCS
- 发布
- 1985
- 实施
3.1 This test method provides a practical means of assessing glass pipe strength under short-duration, thermally-imposed tensile stresses. In addition to a principal role played by the linear coefficient of thermal expansion, glass surface defects can also be major factors in reducing downshock performance. 1.1 Since thermal shock resistance is so closely related to the linear coefficient of expansion, this test method for the determination of the thermal shock resistance of glass process pipe is primarily intended to supplement test results on the linear coefficient of expansion, Test Method E228. This thermal shock test will not ordinarily be performed except in those cases where the thermal shock resistance may be questioned. 1.2 This test method covers only two of four thermal shock possible approaches, namely independent downshock of outside and inside pipe surfaces. Downshock is more severe since a higher tensile stress is produced and, hence, more likely to produce failure. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Test Method of Thermal Shock Test on Glass Pipe
- ICS
- 23.040.50
- CCS
- 发布
- 1985
- 实施
ULC unable to provide withdrawal date. Nov. 13, 2009
Guide for Glass Reinforced Pipe and Fittings for Flammable Liquids
- ICS
- 23.040.50
- CCS
- 发布
- 1984-06-01
- 实施
Precast concrete pipes of composite construction - Precast concrete pipes strengthened by chopped zinc-coated steel fibres
- ICS
- 23.040.50
- CCS
- Q14
- 发布
- 1983-07-29
- 实施
- 1983-07-29
Настоящий стандарт распространяется на железобетонные предварительно напряженные напорные раструбные трубы, изготовляемые из тяжелого
Reinforced-concrete vibrohydropressed pressure pipes. Specifications
- ICS
- 23.040.50
- CCS
- 发布
- 1983
- 实施
- 1985-01-01
Настоящий стандарт распространяется на железобетонные предварительно напряженные напорные раструбные трубы, изготовляемые из тяжелого
Reinforced concrete vibrohydropressed pressure pipes. Structure and dimensions
- ICS
- 23.040.50
- CCS
- 发布
- 1983
- 实施
- 1985-01-01
Building and sanitary pipes in asbestos-cement
- ICS
- 23.040.50
- CCS
- Q14
- 发布
- 1982-07
- 实施
Recommended procedure for the installation of pipelines for both pressure and non-pressure application. Covers the types of laying conditions most commonly encountered in practice.
Guide for laying of asbestos-cement pipelines
- ICS
- 23.040.50
- CCS
- Q14
- 发布
- 1980-08-29
- 实施
- 1980-08-29
Applies to pipelines above or below ground, conveying fluids, with or without internal hydraulic pressure. Outlines the basic methods of pressure testing and two main types of tests are specified.
Methods for field pressure testing of asbestos-cement pipelines
- ICS
- 23.040.50
- CCS
- Q14
- 发布
- 1980-06-30
- 实施
- 1980-06-30
Asbestos-cement pipes, joints and fittings for sewerage and drainage
- ICS
- 23.040.50
- CCS
- Q14
- 发布
- 1980-02
- 实施
Connecting pieces and accessories of glass pipings. Specifications
- ICS
- 23.040.50
- CCS
- 发布
- 1980
- 实施
- 1981-07-01
