23.040.50 其他材料的管和配件 标准查询与下载

ASTM C1103M-19 已安装的预制混凝土污水管接头验收试验的标准实施规程（米制）

1.1 This practice covers procedures for testing the joints of installed precast concrete pipe sewer lines, when using either air or water under low pressure to demonstrate the integrity of the joint and the construction procedures. This practice is used for testing precast concrete sewer lines utilizing rubber gasket sealed joints. NOTE 1—The user of this practice is advised that methods described herein may also be used as a preliminary test to enable the manufacturer or installer to demonstrate the condition of sewer pipe prior to delivery. 1.2 This practice is the SI companion of Practice C1103. NOTE 2—The owner shall specify the following: who will conduct, observe, and furnish labor, material, and measuring devices and pay for the tests; who is responsible for determining local ground conditions; and whether an air or water test is to be used. NOTE 3—The user of this practice is advised that test criteria presented in this practice are similar to those in general use. Pipe shall be accepted by infiltration or exfiltration testing utilizing Practice C969M. NOTE 4—Test times tabulated and the rate of air loss in this standard are based on successful testing of installed pipelines. However, since air and water have different physical properties, retests of some pipelines not meeting field air tests have been successful when tested with water. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific safety precautions are given in Section 6. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Joint Acceptance Testing of Installed Precast Concrete Pipe Sewer Lines (Metric)

ASTM C1214-19 用负压（真空）试验方法测定混凝土排水管的标准试验方法

1.1 This test method covers procedures for testing concrete pipe sewerlines, when using the negative air pressure (vacuum) test method to demonstrate the integrity of the installed material and the construction procedures. This test method covers testing of 4 to 36-in. diameter circular concrete pipe sewerlines utilizing gasketed joints. NOTE 1—The user of this test method is advised that methods described herein may also be used as a preliminary test to enable the manufacturer or installer to demonstrate the condition of sewer pipe prior to delivery or backfill. Minimum test times presented in Table 1 are for pipelines. Holding times for testing an individual pipe may have to be increased to allow for the accumulation of leakage when the tested pipe are incorporated into a continuous pipeline. NOTE 2—The user of this test method is advised that the negative air pressure (vacuum) test criteria presented in this test method are similar to those in general use. The test and criteria have been used widely and successfully in testing smaller diameter pipe. Larger pipe will be accepted more conveniently by visual inspection and individual joint testing. NOTE 3—Test times tabulated and the rate of air loss in this standard are based on successful testing of installed pipelines. However, since air and water have different physical properties, retests of some pipelines not meeting field air tests have been successful when tested with water. 1.2 This test method is the inch-pound companion to Test Method C1214M; therefore, no SI equivalents are presented in the test method. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. See Section 6 for specific safety precautions. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Concrete Pipe Sewerlines by Negative Air Pressure (Vacuum) Test Method

ASTM C497-19 混凝土管、混凝土箱形截面、人孔截面或瓷砖的标准试验方法

Standard Test Methods for Concrete Pipe, Concrete Box Sections, Manhole Sections, or Tile

ASTM C985M-19 无钢筋混凝土规定强度涵洞、雨水管和污水管的标准规范（米制）

1.1 This specification covers nonreinforced concrete pipe designed for specified strengths and intended to be used for the conveyance of sewage, industrial wastes, and storm water and for the construction of culverts. 1.2 This specification is the metric counterpart of Specification C985. NOTE 1—This specification is a manufacturing and purchase specification only and does not include requirements for bedding, backfill, or the relationship between field load conditions and the designated strength of the pipe. However, experience has shown that the successful performance of this product depends upon the proper selection of the pipe strength, type of bedding and backfill, and care that the installation conforms to the construction specifications. The owner of the concrete pipe specified herein is cautioned that he must correlate the field requirements with the pipe strength specified and provide inspection at the construction site. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Nonreinforced Concrete Specified Strength Culvert, Storm Drain, and Sewer Pipe (Metric)

ASTM C497M-19 混凝土管、混凝土箱形截面、人孔截面或瓷砖的标准试验方法（米制）

Standard Test Methods for Concrete Pipe, Concrete Box Sections, Manhole Sections, or Tile (Metric)

ASTM C76M-19 钢筋混凝土涵洞、雨水管和污水管的标准规范（米制）

Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe (Metric)

ASTM C1103-19 已安装的预制混凝土污水管接头验收试验的标准实施规程

Standard Practice for Joint Acceptance Testing of Installed Precast Concrete Pipe Sewer Lines

ASTM C76-19 钢筋混凝土涵洞、雨水管和污水管的标准规范

Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe

ASTM C506M-18 钢筋混凝土拱廊 风暴排水管和下水道管道标准规范（公制）

Standard Specification for Reinforced Concrete Arch Culvert, Storm Drain, and Sewer Pipe (Metric)

ASTM C76M-18a 钢筋混凝土涵洞、雨水管和污水管的标准规范（米制）

Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe (Metric)

ASTM C507-18a 钢筋混凝土椭圆形套管 风暴排水管和下水道管道标准规范

Standard Specification for Reinforced Concrete Elliptical Culvert, Storm Drain, and Sewer Pipe

ASTM C506-18 钢筋混凝土拱廊 风暴排水和下水道管道标准规范

Standard Specification for Reinforced Concrete Arch Culvert, Storm Drain, and Sewer Pipe

ASTM C655-18 钢筋混凝土D型装载机 风暴排水管和下水道管道标准规范

Standard Specification for Reinforced Concrete D-Load Culvert, Storm Drain, and Sewer Pipe

ASTM C507M-18 钢筋混凝土椭圆形水泥 风暴排水和下水道管道标准规范（公制）

Standard Specification for Reinforced Concrete Elliptical Culvert, Storm Drain, and Sewer Pipe (Metric)

ASTM C1818-18 合成纤维增强混凝土 风暴排水和下水道管道标准规范

Standard Specification for Synthetic Fiber Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe

ASTM C76-18a 钢筋混凝土涵洞、雨水管和污水管的标准规范

Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe

ASTM C655M-18 钢筋混凝土承载盖 风暴排水管和下水管（公制）标准规范

Standard Specification for Reinforced Concrete D-Load Culvert, Storm Drain, and Sewer Pipe (Metric)

ASTM C1765-18 钢纤维钢筋混凝土标准规范 风暴排水管和下水管

Standard Specification for Steel Fiber Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe

ASTM C1478-18 钢筋混凝土风暴下水道结构 管道和侧倾之间的风暴排水弹性连接器的标准规范

Standard Specification for Storm Drain Resilient Connectors Between Reinforced Concrete Storm Sewer Structures, Pipes, and Laterals

ASTM C301-18 玻璃化粘土管的标准试验方法

Standard Test Methods for Vitrified Clay Pipe