23.040.50 其他材料的管和配件 标准查询与下载

ASTM C1478-18 钢筋混凝土风暴下水道结构 管道和侧倾之间的风暴排水弹性连接器的标准规范

Standard Specification for Storm Drain Resilient Connectors Between Reinforced Concrete Storm Sewer Structures, Pipes, and Laterals

ASTM C700-18 陶瓷粘土管标准规格 超强度 标准强度和穿孔

Standard Specification for Vitrified Clay Pipe, Extra Strength, Standard Strength, and Perforated

ASTM C497-18b 检查井段或瓷砖混凝土管的标准试验方法

Standard Test Methods for Concrete Pipe, Manhole Sections, or Tile

ASTM C497-18a 检查井段或瓷砖混凝土管的标准试验方法

Standard Test Methods for Concrete Pipe, Manhole Sections, or Tile

ASTM C497M-18 人孔型或瓷砖混凝土管的标准试验方法（米制）

Standard Test Methods for Concrete Pipe, Manhole Sections, or Tile (Metric)

ASTM C76M-18 钢筋混凝土涵洞、雨水管和污水管的标准规范（米制）

Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe (Metric)

ASTM C76-18 钢筋混凝土涵洞、雨水管和污水管的标准规范

Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe

ASTM C1675-18 涵洞、雨水道和下水道用预制钢筋混凝土整体箱形截面的安装

Standard Practice for Installation of Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers

ASTM D6244-06(2018) 土工合成材料路面板排水管垂直压缩的标准试验方法

1.1 This test method covers vertical strain and core area change of geocomposite pavement drains, such as those included in Specification D7001, under vertical compression. 1.2 The values as stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Vertical Compression of Geocomposite Pavement Panel Drains

ASTM C507-18 钢筋混凝土椭圆形套管 风暴排水管和下水道管道标准规范

Standard Specification for Reinforced Concrete Elliptical Culvert, Storm Drain, and Sewer Pipe

ASTM C1786-18 AASHTO LRFD设计的暗渠 雨水渠和下水道用节段预制钢筋混凝土箱形截面的标准规范

Standard Specification for Segmental Precast Reinforced Concrete Box Sections for Culverts, Storm Drains, and Sewers Designed According to AASHTO LRFD

ASTM C497-18 检查井段或瓷砖混凝土管的标准试验方法

Standard Test Methods for Concrete Pipe, Manhole Sections, or Tile

ASTM C1433M-18 标准规范涵洞 雨水渠和下水道预制钢筋混凝土整体箱形截面（公制）

Standard Specification for Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers (Metric)

ASTM C1786-17 AASHTO LRFD设计的暗渠 雨水渠和下水道用节段预制钢筋混凝土箱形截面的标准规范

Standard Specification for Segmental Precast Reinforced Concrete Box Sections for Culverts, Storm Drains, and Sewers Designed According to AASHTO LRFD

ASTM C969-17 已安装的预制混凝土污水管道的渗透和渗出验收试验的标准实施规程

1.1 This practice covers procedures for testing installed precast concrete pipe sewer lines using either water infiltration or exfiltration acceptance limits to demonstrate the integrity of the installed materials and construction procedure. 1.2 This practice is the inch-pound companion to Practice C969M; therefore, no SI equivalents are presented in the practice. NOTE 1—The owner shall specify the following: who will conduct, observe, and furnish labor, furnish material and measuring devices, and pay for the tests; who is responsible for determining local groundwater conditions; and which test is to be conducted, that is, an infiltration test or an exfiltration test. NOTE 2—The user of this practice is advised that test criteria presented in this practice are similar to those in general use. Pipe, 24-in. diameter or larger, may be accepted by visual inspection when testing for infiltration. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Infiltration and Exfiltration Acceptance Testing of Installed Precast Concrete Pipe Sewer Lines

ASTM C1840/C1840M-17 安装钢筋混凝土 风暴排水和风雨管道管道检验验收标准实施

1.1 This practice covers the requirements for inspection and acceptance of installed reinforced concrete pipe by either person-entry, or remote inspection as shown in Figs. 1 and 2, respectively. 1.2 The scope of this specification is intended for installation related observations and assumes that pre-installation inspection has been completed. 1.3 The reinforced concrete culvert, storm drain and storm sewer pipe shall be manufactured in accordance with Specification C76, C506, C507, C655, or C1417 and accepted in accordance with AASHTO R073. This specification shall only be used for gravity, non-pressure storm drainage applications. 1.4 Person Entry shall be used unless extenuating circumstances preclude this type inspection. Remote inspection is acceptable for use for pipe diameters of 30 in. [750 mm] and smaller unless otherwise specified by owner or engineer. 1.5 Access of installed pipe for manual inspection shall follow OSHA 29 CFR PART 1926 SUBPART AA regulations for confined space entry. However, this standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.6 This practice does not cover deformation or deflection assessment. Concrete pipe is classified as a rigid structure because they do not bend or deflect appreciably under load before cracking. Due to these facts shape evaluation are of little or no value when evaluating concrete pipe. 1.7 The values stated in either Imperial/US or [SI units] are to be regarded separately as standard. The SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Inspection and Acceptance of Installed Reinforced Concrete Culvert, Storm Drain, and Storm Sewer Pipe

ASTM C969M-17 已安装的预制混凝土排水管的渗透和渗出验收试验的标准实施规程（米制）

1.1 This practice covers procedures for testing installed precast concrete pipe sewer lines using either water infiltration or exfiltration acceptance limits to demonstrate the integrity of the installed materials and construction procedure. 1.2 This practice is the SI companion of Practice C969. NOTE 1—The owner shall specify the following: who will conduct, observe, and furnish labor, furnish material and measuring devices, and pay for the tests; who is responsible for determining local groundwater conditions; and which test is to be conducted, that is, an infiltration test or an exfiltration test. NOTE 2—The user of this practice is advised that test criteria presented in this practice are similar to those in general use. Pipe, 600-mm diameter or larger, may be accepted by visual inspection when testing for infiltration. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Infiltration and Exfiltration Acceptance Testing of Installed Precast Concrete Pipe Sewer Lines (Metric)

ASTM C1675-17 涵洞、雨水道和下水道用预制钢筋混凝土整体箱形截面的安装

Standard Practice for Installation of Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers

ASTM C497M-17 人孔型或瓷砖混凝土管的标准试验方法（米制）

1.1 These test methods cover testing of concrete pipe, manhole sections, and tile. The test methods described are used in production testing and acceptance testing to evaluate the properties provided for in the specifications. 1.2 The test methods appear in the following order: Section External Load Crushing Strength 4 Flat Slab Top 5 Core Strength 6 Absorption 7 Hydrostatic 8 Permeability 9 Manhole Step 10 Cylinder 11 Gasket Lubricant 12 Joint Shear 13 Alkalinity 14 Gasket Measurements 15 1.3 The test specimens shall not have been exposed to a temperature below 4°C for the 24 h immediately preceding the test. 1.4 If any test specimen fails because of mechanical reasons such as failure of testing equipment or improper specimen preparation, it shall be discarded and another specimen taken. 1.5 Specimens shall be selected in accordance with the specifications for the type of pipe or tile being tested. 1.6 These methods are the metric companion of Test Methods C497. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Concrete Pipe, Manhole Sections, or Tile (Metric)

ASTM C444-17 穿孔混凝土管道标准规范

1.1 This specification covers perforated concrete pipe intended to be used for underdrainage. 1.2 This specification is the inch-pound companion to Specification C444M; therefore, no SI equivalents are presented in the specification. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Perforated Concrete Pipe