23.060.01 阀门综合 标准查询与下载

ASTM A592/A592M-10(2020) 压力容器用高强度调质低合金钢锻件的标准规范

1.1 This specification2 covers high-strength quenched and tempered low-alloy steel forged parts for pressure vessels. The maximum thickness of forgings under this specification shall be 11⁄2 in. [38 mm] for Grade A, and 4 in. [100 mm] for Grades E and F. NOTE 1—These grades are similar to corresponding grades in Specification A517/A517M. 1.2 Although no provision is made for supplementary requirements in this standard, the supplementary requirements in Specification A788/A788M may be considered by the purchaser. 1.3 Welding technique is of fundamental importance and it is presupposed that welding procedures will be in accordance with approved methods for the class of material used. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.5 Unless the order specifies the applicable “M” specification designation, the material shall be furnished to the inchpound units. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for High-Strength Quenched and Tempered Low-Alloy Steel Forged Parts for Pressure Vessels

BS EN ISO 22109:2020 工业阀门 阀门齿轮箱

What is BS EN ISO 22109 about?    BS EN ISO 22109 discusses industrial valves. BS EN ISO 22109 provides basic requirements for gearboxes to operate industrial valves for manual and automated on/off and modulating duties. This includes manual override gearboxes. BS EN ISO 22109 includes guidelines for classification, design and methods for conformity assessment.   BS EN ISO 22109 specifies three kinds of operation:  

Industrial valves. Gearbox for valves

EN ISO 22109:2020 工业阀门.阀门齿轮箱

This document provides basic requirements for gearboxes to operate industrial valves for manual and automated on/off and modulating duties, this includes manual override gearboxes. It includes guidelines for classification, design and methods for conformity assessment. It does not cover gear systems which are integral part in the design of valves and subsea gearboxes. Other requirements or conditions of use different from those indicated in this document are agreed between the purchaser and the manufacturer or supplier (first party), prior to order.

Industrial valves - Gearbox for valves (ISO 22109:2020)

ISO 22109:2020 工业阀门.阀门齿轮箱

This document provides basic requirements for gearboxes to operate industrial valves for manual and automated on/off and modulating duties, this includes manual override gearboxes. It includes guidelines for classification, design and methods for conformity assessment. It does not cover gear systems which are integral part in the design of valves and subsea gearboxes. Other requirements or conditions of use different from those indicated in this document are agreed between the purchaser and the manufacturer or supplier (first party), prior to order.

Industrial valves — Gearbox for valves

ISO 22153:2020 工业阀门用电动执行机构.一般要求

This document provides basic requirements for electric valve actuators, used for on-off and control valves. It includes guidelines for classification, design, enclosure and corrosion protection, and methods for conformity assessment. Combinations of electric actuators and gearboxes when supplied by the actuator manufacturer are within the scope of this document. This document does not cover solenoid actuators, electro-hydraulic actuators and electric actuators which are integral to the valves. Other requirements or conditions of use different from those indicated in this document are agreed between the purchaser and the manufacturer/supplier, prior to order.

Electric actuators for industrial valves — General requirements

T/JMBX 0090-2019 卫生洁具 直角阀

7.1 外观 7.1.1 镀层表面光泽均匀，应无脱皮、龟裂、烧焦、露底、剥落、黑斑及明显的麻点、毛刺等缺陷。 7.1.2 涂层表面组织细密、光滑、色泽均匀，应无流挂、露底及明显的划痕和磕碰等缺陷。 7.1.3 抛光表面应光滑，应无明显毛刺、划痕和磕碰等缺陷。 7.1.4 塑料件表面应光滑、色泽均匀，应无明显的斑痕、划痕和凹痕。

Right-angle valve for sanitary appliance

KS B 2822-2019 开槽型橡胶层次蝶阀

Grooved type rubber-seated butterfly valves

T/ZZB 1327-2019 液化天然气阀门

本标准规定了液化天然气用闸阀、截止阀、止回阀、球阀和蝶阀的基本要求、技术要求、检验、试验方法、检验规则、标志、包装、运输和贮存及质量承诺。 本标准适用于公称压力PN16～PN250，公称尺寸DN15～DN1200和压力等级Class150～Class1500、公称尺寸NPS1/2～NPS48，工作介质为液化天然气的法兰和焊接连接的阀门（以下简称阀门）。

Liquefied natural gas valves

T/CMA SB041-2019 水表用电控阀

本标准规定了水表用电控阀的结构、材料、技术要求、试验方法、检验规则、标志、包装和贮存。

Electric control valve for water meter

DB41/T 1883-2019 安全阀在线校验规则

On-line calibration rules for safety valves

ASTM F1387-19 管道和管道机械连接管件的性能标准规范

1.1 This specification establishes the performance characteristics required for mechanically attached fittings (MAFs) for use in piping and tubing systems. These fittings directly attach to pipe or tube by mechanical deformation of the pipe or tube or fitting, or a combination thereof, creating a seal and a restrained joint. The seal may be created via the mechanical deformation or created independently. Successful completion of the tests described constitutes completion of the technical portion of the qualification process. 1.2 Supplementary requirements are provided for use when additional testing or inspection is desired. These shall apply only when specified in part or whole by the purchaser in the order. Unless otherwise specified, U.S. Navy contracts shall invoke the supplementary requirements in whole. 1.3 Unless specific MAF types are specified, the term “MAF” shall apply to all types described herein. 1.4 The tests specified in Section 13 and described in Annex A1 and the Supplementary Requirements Section are applicable only to ascertain the performance characteristics of MAFs. These tests are not intended for use in the evaluation of non-MAF products. 1.5 A fire performance test is specified in Supplementary Requirement S7. This test provides general guidelines to determine the responsiveness of MAFs when subjected to fire. This test should not be considered for use to evaluate non-MAF products. 1.6 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.7 The following safety hazards caveat applies only to the tests listed in Section 13 and the tests described in the Supplementary Requirements Section and the annexes of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings

T/WZBF 003-2019 钢制阀门用缠绕式垫片

本标准规定了钢制阀门用缠绕式垫片的型式、代号、尺寸、要求、检验方法、标志、包装、贮运。本标准适用于钢制阀门的机构组件中法兰连接面和阀门与管道连接法兰端所选用的缠绕式垫片。

Spiral wound gasket for steel valve

T/WZBF 004-2019 阀门用柔性石墨填料

本标准规定了阀门用柔性石墨填料环和柔性石墨编织填料模压环的分类、要求、检验、标志、包装和贮存.

Flexible graphite packing for valve

BS ISO 5209:2019 通用工业阀门 标记

What is ISO 5209 - General purpose industrial valves about?    ISO 5209 discusses general-purpose industrial valves. A valve is a device or  natural object  that regulates, directs, or controls the flow of a fluid (gases, liquids, fluidized solids, or  slurries ) by opening, closing, or partially obstructing various passageways. ISO 5209 specifies the requirements for the mandatory and optional markings of general-purpose industrial valves. ISO 5209 defines the method of applying the markings, on the body, on a flange, on an identification plate or any other location. ISO 5209 ...

General purpose industrial valves. Marking

ISO 5209:2019 一般用途工业阀 - 标示

This document specifies the requirements for the mandatory and optional markings of general purpose industrial valves. It defines the method of applying the markings, on the body, on a flange, on an identification plate or any other location. This document is considered in conjunction with the specified requirements of the valve product standards or valve performance standards. The marking requirements for plastic valves are not within the scope of this document.

General purpose industrial valves — Marking

T/ZZB 1023-2019 石油、石化、天然气及相关工业用气动调节阀

本标准规定了石油、石化、天然气及相关工业用气动调节阀（以下简称调节阀）的术语和定义、基本要求、技术要求、试验方法、检验规则、标志、包装、贮存、质量承诺。 本标准适用于公称尺寸DN50～DN300（NPS2～NPS12）、公称压力PN16～PN260（Class150～Class1500）带有电/气阀门定位器的直行程气动调节阀。

Pneumatic control valves for petroleum， petrochemical， natural gas and related industries

T/CEEIA 312-2018 超临界及超超临界机组安全阀 技术条件

本标准共九章，其主要章节内容：第1章 范围、第2章 规范性引用文件、第3章 术语和定义、第4章 结构形式、第5章 设计 本章规定了总则、阀体及弹簧等的一般要求、第6章 材料 本章规定了安全阀用主要部件的材料的要求、第7章 性能要求 本章规定了电站安全阀整定压力偏差、排放压力、启闭压差、机械特性、密封性、排量等性能要求、第8章 试验 本章规定了安全阀试验项目和测量装置、壳体强度、动作性能试验、密封性要求、抽样检验的样机要求及检验方法、排量试验、排量系数的确定等规定。第9章 标志和铅封 本章规定了电站安全阀标志和铅封的要求。

Specification for Safety Valve of Supercritical and Ultra-supercritical Units

T/CGMA 041004-2018 截止阀 产品质量分等规范

本标准规定了截止阀产品的质量等级、试验与检验方法、抽样和评定方法。

Globe valve product quality grading specification

JIS B 2003 AMD 1:2018 阀门检验总则（修正案1）

General rules for inspection of valves (Amendment 1)

DB15/T 1503-2018 安全阀在线校验应用导则

Application guidelines for online calibration of safety valves