23.060.01 阀门综合 标准查询与下载
共找到 868 条与 阀门综合 相关的标准，共 58 页
This European standard applies to metallic valves as pressure accessories for industrial applications with a maximum allowable pressure PS greater than 0,5 bar in accordance with the Pressure Equipment Directive 2014/68/EU and specifies minimum requirements applicable to design, manufacture, testing, materials and documentation. All relevant essential safety requirements of the Pressure Equipment Directive 2014/68/EU applicable to valves have been taken into consideration and are addressed in this standard. This standard is not applicable to: - safety valve and bursting disc (a safety accessory); - sight glass with its frames (component of a pressure equipment) and; - measurement chambers. For other exclusions refer to the PED.
Industrial valves - Requirements and testing for metallic valves as pressure accessories (Incorporates Amendment A1: 2018)
- ICS
- 23.060.01
- CCS
- J16
- 发布
- 2016-04
- 实施
Industrial valves. Marking of metallic valves
- ICS
- 23.060.01
- CCS
- J16
- 发布
- 2016-03-31
- 实施
- 2016-03-31
本标准规定了蒸压釜快开门联锁装置（以下简称联锁装置）的术语和定义、总则、总体安全性能要求、联锁装置机构组成及技术性能要求、改造与修理、检验与评价等基本内容和基本要求。 本标准适用于设计压力≤1.6MPa，设计温度≤204℃的钢制蒸压釜联锁装置。
Safety technical requirements for quick-opening interlock device of autoclave
- ICS
- 23.060.01
- CCS
- Y63
- 发布
- 2016-03-07
- 实施
- 2016-06-07
This European Standard specifies the requirements for marking of industrial metallic valves. It defines the method of applying the markings, on the body, on a flange, on an identification plate or any other location. When specified as a normative reference in a valve product or performance standard, this European Standard has to be considered in conjunction with the specified requirements of that valve product or performance standard. The marking requirements for plastic valves are not within the scope of this European Standard.
Industrial valves - Marking of metallic valves
- ICS
- 23.060.01
- CCS
- J16
- 发布
- 2016-03
- 实施
District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Steel valve assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene; German version EN 488:2015
- ICS
- 23.060.01
- CCS
- P46
- 发布
- 2016-02
- 实施
本标准规定了液化天然气用阀门(以下简称阀门)性能试验的术语和定义、试验项目、常温性能试验、低温性能试验。 本标准适用于公称压力PN16~PN250、公称尺寸DN15~DN1200和压力等级Class150~Class1 500、公称尺寸NPS1/2~NPS48，工作介质为液化天然气的法兰和焊接连接的闸阀、截止阀、止回阀、球阀和蝶阀。 其他类型的阀门亦可参照使用。
Liquified natural gas valves.Performance testing
- ICS
- 23.060.01
- CCS
- J16
- 发布
- 2016-01-15
- 实施
- 2016-06-01
本标准规定了液化天然气用闸阀、截止阀、止回阀、球阀和蝶阀的术语和定义，技术要求，检验、试验方法，检验规则，标志，涂漆，包装，运输和贮存。 本标准适用于公称压力PN16~PN250、公称尺寸DN15~DN1 200和压力等级class150~class1500、公称尺寸NPS1/2~NPS48，工作介质为液化天然气的法兰和焊接连接的阀门(以下简称阀门)。 其他温度高于－162℃的低温阀门亦对参照使用。
Liquified natural gas valves.Technical requirements
- ICS
- 23.060.01
- CCS
- J16
- 发布
- 2016-01-15
- 实施
- 2016-06-01
本标准规定了火力发电用止回阀的结构型式、选型、出厂检验与监造、现场安装、运行维护与检修等内容。 本标准适用于火力发电厂汽、水系统角法兰、焊接、对夹连接的止回阀，其工作压力小于等于45MPa，工作温度小于等于630℃。
Selection and Manipulation Regulations of Check Valve for Power Plant
- ICS
- 23.060.01
- CCS
- J16
- 发布
- 2016-01-07
- 实施
- 2016-06-01
Pipeline valves. Welding and quality control of welded joints. Technical requirements
- ICS
- 23.060.01
- CCS
- 发布
- 2016-00-00
- 实施
- 2018-01-01
Pipeline valves. Method of fire testing
- ICS
- 23.060.01
- CCS
- 发布
- 2016-00-00
- 实施
- 2018-01-01
Industrial valves－Measurement, test and qualification procedures for fugitive emissions－Part 2：Production acceptance test
- ICS
- 23.060.01
- CCS
- 发布
- 20151229
- 实施
- 20151229
Industrial valves－Part-turn actuator attachment
- ICS
- 23.060.01
- CCS
- 发布
- 2015-12-29
- 实施
Industrial valves－Part-turn actuator attachment
- ICS
- 23.060.01
- CCS
- 发布
- 2015-12-29
- 实施
Face-to-face and end-to-end dimensions of valves
- ICS
- 23.060.01
- CCS
- 发布
- 2015-12-29
- 实施
General rules for marking on valves
- ICS
- 23.060.01
- CCS
- 发布
- 2015-12-29
- 实施
Industrial valves - End-to-end and centre-to-end dimensions for valves with threaded ends; German version EN 16722:2015
- ICS
- 23.060.01
- CCS
- J16
- 发布
- 2015-12
- 实施
District heating pipes. Preinsulated bonded pipe systems for directly buried hot water networks. Steel valve assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene
- ICS
- 23.060.01
- CCS
- Q83
- 发布
- 2015-11-30
- 实施
- 2015-11-30
This part of ISO 28921 specifies requirements for the type testing of isolating valves for low-temperature applications to verify the performance of valves at a low temperature from – 50 °C down to – 196 °C. NOTE Nominal sizes (DN), nominal pipe sizes (NPS), nominal pressure (PN) and Classes are covered in This part of ISO 28921 does not evaluate valve actuators unless they are integral part of the valve. Valves during testing can be operated manually or an actuator can be used during the testing. The effect of cold gas vapours during testing is taken into consideration in particular if the actuator is mounted directly over the test stand with the cold gases engulfing the actuator. This part of ISO 28921 does not apply to valves for cryogenic services, designed in accordance with
Industrial valves - Isolating valves for low-temperature applications - Part 2: Type testing
- ICS
- 23.060.01
- CCS
- J16
- 发布
- 2015-11-01
- 实施
