23.060.01 阀门综合 标准查询与下载

EN 488:2015 区域供暖管道.直埋热水网路预绝缘、结合管道系统.钢管, 聚氨酯保温材料以及聚氨酯外壳的钢阀门装配

This European Standard specifies requirements and test methods for valves of prefabricated thermally insulated valve assemblies comprising a steel valve, rigid polyurethane foam insulation and an outer casing of polyethylene for use in directly buried hot water networks with pre-insulated pipe assemblies in accordance with EN 253. This European Standard applies only to factory made prefabricated insulated valve assemblies for continuous operation with hot water at various temperatures in accordance with EN 253:2009+A2:2015, Clause 1 and the valve assemblies with a maximum operation pressure of 25 bar. For higher pressures, additional demands apply. NOTE For this application, the following valve types are commonly used: ball valves, gate valves, and butterfly valves. This European Standard does not include calculation rules for loads and stresses. These depend on the configuration of the system as it is installed. The design and installation rules are given in EN 13941.

District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Steel valve assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene

DIN EN ISO 15848-1:2015 工业阀.漏气的测量、试验和鉴定程序.第1部分:阀门定型试验的分类系统和鉴定程序(ISO 15848-1-2015);德文版本EN ISO 15848-1-2015

Industrial valves - Measurement, test and qualification procedures for fugitive emissions - Part 1: Classification system and qualification procedures for type testing of valves (ISO 15848-1:2015); German version EN ISO 15848-1:2015

DIN EN ISO 15848-2:2015 工业用阀.漏气的测量、试验和鉴定程序.第2部分:阀门生产验收试验(ISO 15848-2-2015);德文版本EN ISO 15848-2-2015

Industrial valves - Measurement, test and qualification procedures for fugitive emissions - Part 2: Production acceptance test of valves (ISO 15848-2:2015); German version EN ISO 15848-2:2015

BS EN 16722:2015 工业阀门. 带有螺纹端的阀门的端至端和中心到端的尺寸

Industrial valves. End-to-end and centre-to-end dimensions for valves with threaded ends

JB/T 12746-2015 含缺陷高温压力管道和阀门安全评定方法

Safety assessment method for defective high-temperature pressure pipelines and valves

GSO ISO 8233:2015 热塑性阀门 扭矩 试验方法

This International Standard specifies a test method for the determination of the opening and closing torque of thermoplastics valves.

Thermoplastics valves -- Torque -- Test method

EN 16722:2015 工业阀门.端口到端口和中心到端口维度的螺纹末端阀门

This European Standard specifies the end-to-end and centre-to-end dimensions for valves with threaded ends with connecting dimensions in compliance with EN ISO 228-1 or EN 10226-1, used in PN and Class designated piping systems. The range of PN is: -PN 10; PN 16; PN 25; PN 40; PN 63; PN 100; PN 160; PN 250; PN 320; PN 400. The range of Class is; - Class 150, Class 300, Class 600, Class 900, Class 1500, Class 2500. The range of nominal size is; - DN 4; DN 6; DN 8; DN 10; DN 15; DN 20; DN 25; DN 32; DN 40; DN 50; DN 65; DN 80; DN 100. NOTE 1 See Annex C for the relationship between nominal size (DN) and nominal pipe size (NPS). NOTE 2 Valves having screwed end profiles different from those specified in EN ISO 228-1 or EN 10226-1, may use the same dimensions than those specified in Table 1.

Industrial valves - End-to-end and centre-to-end dimensions for valves with threaded ends

BS ISO 5208:2015 工业阀门 金属阀门的压力测试

Industrial valves. Pressure testing of metallic valves

BS EN ISO 15848-2:2015 工业阀门 无组织排放的测量、测试和鉴定程序 阀门生产验收试验

Industrial valves. Measurement, test and qualification procedures for fugitive emissions. Production acceptance test of valves

BS EN ISO 15848-1:2015 工业阀门.漏气的测量、试验和鉴定程序.阀门定型试验的分类系统和鉴定程序

Industrial valves. Measurement, test and qualification procedures for fugitive emissions. Classification system and qualification procedures for type testing of valves

EN ISO 15848-2:2015 工业阀门.测量,测试和不易收集的排放的资格程序.第2部分:生产验收测试阀门(ISO 15848 - 2:2015)

Dieser Teil von ISO 15848 legt Prüfverfahren für die Bewertung der äußeren Undichtheit von Armaturenschäften oder -wellen und Gehäuseverbindungen von Absperrarmaturen und Stellgeräten zur Verwendung mit flüchtigen luftverunreinigenden Stoffen und gefährlichen Flüssigkeiten fest. Anschlussverbindungen, Anwendungen in der Vakuumtechnik, Auswirkungen von Korrosion und Bestrahlung fallen nicht in den Anwendungsbereich dieses Teils von ISO 15848. Das fertigungsbegleitende Abnahmeprüfverfahren ist für standardgefertigte Armaturen bestimmt, für die Normen über flüchtige Emissionen gelten.

Industrial valves - Measurement, test and qualification procedures for fugitive emissions - Part 2: Production acceptance test of valves (ISO 15848-2:2015)

EN ISO 15848-1:2015 工业阀门.测量,测试和资格程序短时排放.第1部分:类型测试阀门的分类系统和资格程序(ISO 15848 - 1:2015)

Dieser Teil von ISO 15848 legt Prüfverfahren für die Bewertung der äußeren Undichtheit von Schaft- bzw. Wellenabdichtungen von Armaturen, Gehäuseverbindungen von Absperrventilen und Stellgeräten zur Verwendung mit flüchtigen luftverunreinigenden Stoffen und gefährlichen Flüssigkeiten fest. Anschlussverbindungen, Anwendungen in der Vakuumtechnik, Auswirkungen von Korrosion und Bestrahlung fallen nicht in den Anwendungsbereich dieses Teils von ISO 15848. Dieser Teil von ISO 15848 beinhaltet ein Klassifizierungssystem und Qualifikationsverfahren für die Durchführung von Bauartprüfungen an Armaturen.

Industrial valves - Measurement, test and qualification procedures for fugitive emissions - Part 1: Classification system and qualification procedures for type testing of valves (ISO 15848-1:2015)

ISO 5208:2015 工业阀门.金属阀门的压力试验

Industrial valves - Pressure testing of metallic valves

ISO 15848-2:2015 工业用阀.泄漏的测量、试验和鉴定程序.第2部分:阀门产品验收试验

This part of ISO 15848 specifies test procedures for the evaluation of external leakage of valve stems or shafts and body joints of isolating valves and control valves intended for application with volatile air pollutants and hazardous fluids. End connection joints, vacuum application, effects of corrosion, and radiation are excluded from this part of ISO 15848. The production acceptance test is intended for standard production valves where fugitive emissions standards are specified.

Industrial valves - Measurement, test and qualification procedures for fugitive emissions - Part 2: Production acceptance test of valves

ISO 15848-1:2015 工业阀.漏气的测量、试验和鉴定程序.第1部分:阀门定型试验的分类系统和鉴定程序

This part of ISO 15848 specifies testing procedures for evaluation of external leakage of valve stem seals (or shaft) and body joints of isolating valves and control valves intended for application in volatile air pollutants and hazardous fluids. End connection joints, vacuum application, effects of corrosion, and radiation are excluded from this part of ISO 15848. This part of ISO 15848 concerns classification system and qualification procedures for type testing of valves.

Industrial valves - Measurement, test and qualification procedures for fugitive emissions - Part 1: Classification system and qualification procedures for type testing of valves

LST EN 13175-2015 液化石油气设备和附件. 液化石油气(LPG)压力容器阀门和配件的规格和试验

LPG Equipment and accessories - Specification and testing for Liquefied Petroleum Gas (LPG) pressure vessel valves and fittings

LST EN 12516-1-2015 工业阀门. 外壳设计强度. 第1部分: 钢阀门壳体的列表法

Industrial valves - Shell design strength - Part 1: Tabulation method for steel valve shells

DB34/T 2286-2015 安全阀在线校验规程

本标准规定了安全阀在线校验的术语和定义、一般要求、校验前准备、内容、结果处理、记录与报告的基本要求。 本标准适用于锅炉、固定式压力容器、压力管道上的直接载荷式安全阀的在线校验。

Safety valve on-line calibration procedure

DIN EN 13175:2015 液化石油气设备和附件. 液化石油气 (LPG) 压力容器阀门和配件的规格和试验; 德文版本EN 13175-2014

LPG Equipment and accessories - Specification and testing for Liquefied Petroleum Gas (LPG) pressure vessel valves and fittings; German version EN 13175:2014

JIS B 2031 AMD 1:2015 灰口铸铁阀(修改件1)

Gray cast iron valves (Amendment 1)