23.060.30 闸阀 标准查询与下载

BS EN 593:1998 工业阀门.金属蝶阀

Industrial valves - Metallic butterfly valves

JB/T 8691-1998 对夹式刀形闸阀

本标准规定了对夹式刀形闸阀的定义、分类、要求、试验方法、检验规则、标志、包装、运输、贮存和质量保证。 本标准适用于公称压力PN不大于2.5 MPa、公称通径DN50～700 mm、工作介质为含固体颗粒的流体等的对夹式刀形闸阀。

Wafer knife gate valves

NF E29-430:1998 工业阀门.金属蝶型阀门

Industrial valves. Metallic butterfly valves.

CNS 11090-1997 青铜螺纹口脉动闸阀（８．５ｋｇｆ／ｃ㎡）

本标准适用于压力不稳定之流体管路用青铜制螺纹口闸阀（以下简称阀），其标称压力为 8.5 kgf∕cm2 ，而能承受突然增高至 25 kgf∕cm2 以下之脉冲压力者。其适用流体之状态与最高使用压力之关系如表 1 所示。注：本标准中｛ ｝ 内之值为国际单位制（SI），并记供参考。

Bronze screwed pulse gate valves (8.5kgf/c㎡)

AWWA C510-1997 双止回阀逆流防止组装

This standard describes fabricated steel mechanical slip-type expansion joints having packing chambers for use on pipe with plain, flanged, grooved, or shouldered ends in nominal pipe sizes from 3 in. (75 mm)* through 144 in. (3,600 mm). They shall be

Double Check Valve Backflow Prevention Assembly

KS V 7353-1997(2011) 海洋青铜为20K压力计旋塞

MARINE BRONZE 20K PRESSURE GAUGE COCKS

CNS 12742-1997 水道用蝶型阀（长体型）

本标准适用于标称口径 75mm 至 1800mm ，能完全止水承受压力之长体型水道用蝶型阀（以下简称阀）。

Butterfly valves for water works (Long body type)

TIS 1413-1997 供水用铸铁橡胶座闸阀

Cast iron rubber seated gate valves for water services

TIS 256-1997 供水用铸铁金属座闸阀

Cast iron metal.seated gate valves for water services

CNS 12743-1995 水道用蝶型阀（薄体型）

本标准适用于标称口径 75mm 至 600mm ，能完全止水承受压力之薄体型水道用蝶型阀（以下简称阀）。

Butterfly Valves for Water Works (Wafer Type)

CNS 12741-1995 水道用蝶型阀（短体型）

本标准适用于标称口径 75mm 至 1800mm ，能完全止水承受压力之短体型水道用蝶型阀（以下简称阀）。

Butterfly Valves for Water Works (Short Body Type)

ISO 10631:1994 通用金属蝶阀

Specifies the requirements for metallic butterfly valves with centred or eccentric disc, with centred or eccentric shaft, with metallic, polymeric, elastomeric or composite seating, with lined or unlined body, coated or uncoated, to be used in flanged or butt-welded piping systems for shut-off, throttling or flow control. Covers butterfly valves with nominal diameters DN 40 to DN 2000 and is applicable to valves of nominal pressure PN 2,5 to 50.

Metallic butterfly valves for general purposes

CNS 12795-1993 水道用弹性座封闸阀

本标准适用于标称口径 50mm 至 350mm 之水道用球状石墨铸铁弹性座封闸阀（以下简称阀）。

Resilient - Seated Gate Valves For Water Works

CNS 713-1993 铸铁凸缘型闸阀（１０ｋｇｆ／ｃ㎡）（阀杆非上升型）

本标准适用于标称压力为 10 kgf∕cm2 之铸铁凸缘型闸阀（内螺纹阀杆非上升型）（以下简称阀）。

Cast Iron Flanged Gate Valves ( 10kgf/cm}tg) ( Inside Screw Non-Rising Stem Type)

CNS 714-1993 铸铁凸缘型闸阀（５ｋｇｆ／ｃ>㎡）（阀杆上升型）

本标准适用于标称压力 5 kgf∕cm2 之（阀杆上升型）之铸铁凸缘型闸阀（以下简称阀）。

Cast Iron Flanged Gate Valves ( 5kgf/c㎡) ( Outside Screw Type)

CNS 715-1993 铸铁凸缘型闸阀（１０ｋｇｆ／ｃ㎡）（阀杆上升型）

本标准适用于标称压力 10 kgf∕cm2 之（阀杆上升型）之铸铁凸缘型闸阀（以下简称阀）。

Cast Iron Flanged Gate Valves ( 10kgf/c㎡) ( Outside Screw Type)

GOST 3706-1993 铸造法兰和焊接法兰闸门.制造长度

Настоящий стандарт распространяется на задвижки фланцевые и под приварку из чугуна и стали и устанавливает размеры строительных длин. Ст

Gate valves. End-to-end lengths

ISO 6002:1992 用螺栓连接阀盖的钢制闸阀

Specifies the requirements for valves of nominal sizes DN 10 up to DN 1 000 and nominal pressures PN 10 up to PN 100 having the following features: bolted bonnet, outside screw and yoke, inside screw (alternative for PN 10, 16, 20, 25 and 40 only), single or double obturator, wedge or parallel seating, with or without non-metallic obturator or seat seals, flanged or butt-welding ends.

Bolted bonnet steel gate valves

ASME B16.10 INTERPRETATIONS-1992 B16.10-1992说明.阀门的面对面和端对端尺寸.包括说明1

Interpretations to B16.10-1992 Face-to-Face and End-to-End Dimensions of Valves Includes Interpretation No. 1

Interpretations to B16.10-1992 Face-to-Face and End-to-End Dimensions of Valves Includes Interpretation No. 1

GOST R 50360-1992 闸阀 端到端长度

Gate valves. End-to-end lengths