23.080 泵 标准查询与下载

T/ZZB 1703-2020 一体式混流、轴流潜水电泵

本标准规定了一体式混流、轴流潜水电泵（以下简称“电泵”）的术语和定义、型式和基本参数、基本要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存及质量承诺。 本标准适用于水利、电力排灌用电泵等。

Integrated mixed flow and axial flow submersible pump

JB/T 8059-2020 高压锅炉给水泵 技术条件

本标准规定了高压锅炉给水泵的技术要求，试验方法和检验规则等。 本标准适用于单机容量为200～600MW火力发电机组锅炉给水的泵。50～125 MW容量的火力发电机组用泵可参照采用。

High pressure boiler feed water pump technical conditions

JB/T 13975-2020 内燃机共轴泵

Internal combustion engine coaxial pump

JB/T 7255-2020 水环真空泵和水环压缩机

Water ring vacuum pump and water ring compressor

JB/T 13977-2020 液化天然气（LNG）低温潜液泵

Liquefied Natural Gas (LNG) Cryogenic Submersible Pump

KS B 6302-2019 泵的排放测试方法探讨

Measurement methods of pump discharge

KS B 6504-2019 工程用沈水泵

Submersible pumps for construction

KS B 7513-2019 泵吸入管及输送管的尺寸

Dimensions of suction pipe and delivery pipe for pumps

T/ZZB 1456-2019 柱塞计量泵

本标准规定了柱塞计量泵的术语和定义、 信息确认、 型式和基本参数、基本要求、 技术要求、试验和检验、 检验规则、交付、标志、包装、贮存和质量承诺。 本标准适用于输送温度为-30 ℃~200 ℃、粘度为0.3 mm2/s～2000 mm2/s的不含固体颗粒的液体的柱塞计量泵(以下简称“泵”)。

Plunger metering pump

T/ZZB 1455-2019 液压式隔膜计量泵

本标准规定了液压式隔膜计量泵的术语和定义、信息确认、型式和基本参数、基本要求、技术要求、试验和检验、检验规则、交付、标志、包装、贮存和质量承诺。 本标准适用于输送温度为-30 ℃～150 ℃、粘度为0.3 mm2/s～2000 mm2/s的液体的液压式隔膜计量泵(以下简称“泵” )。

Hydraulic diaphragm metering pump

JB/T 6912-2019 泵产品零件无损检测 磁粉探伤

本标准规定了泵产品零件的干、湿磁粉(包括荧光和非荧光)探伤方法及质量等级评定。 本标准适用于检查铁磁性材料制做的泵产品零件的表面及近表面缺陷。

Non-destructive testing of pump product parts Magnetic particle testing

JB/T 13705-2019 智能热水循环屏蔽电泵

Intelligent hot water circulation shielded electric pump

T/ZZB 1225-2019 保温高黏度三螺杆沥青泵

本标准规定了保温高黏度三螺杆沥青泵的术语和定义、产品标记和构成、基本要求、技术要求、试验方法、检验规则、标志、包装、运输与贮存、质量承诺。 本标准适用于泵体带保温夹套可用导热油或其它高温介质对泵体进行加热， 介质温度（0～250）℃，保温状态下用于输送（3～1500） mm2/s液态沥青的保温高黏度三螺杆沥青泵(以下简称三螺杆沥青泵)。

Thermal insulation high viscosity three screw asphalt pump

ASTM E295-82(2019) 油扩散泵测量速度的标准测试方法

1.1 This test method covers the determination of the measured speed (volumetric flow rate) of oil diffusion pumps. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Measured Speed of Oil Diffusion Pumps

T/ZJWIA 0071-2019 浙江省城乡一体化供水管网梯级加压 泵站调度技术规范

目  录 前言　 1 范围　 2 规范性引用文件　 3 术语和定义　 4 基本规定　 5 数据采集　 5.1 一般规定　 5.2 泵站信息　 5.3 管网信息　 6 运行调度分析及决策　 6.1 一般规定　 6.2 数据分析　 6.3 优化调度方案　 6.4 调度决策与实施　 7 调度与运行管理　 7.1 一般规定　 7.2 调度管理　 7.3 泵站安全　 7.4 应急处置　

Technical specifications for cascade pressurized pump station dispatching of urban and rural integrated water supply network in Zhejiang Province

T/ZZB 1172-2019 智能永磁变频恒压离心电泵

本标准规定了智能永磁变频恒压离心电泵的术语和定义、型式与参数、使用条件、基本要求、技术要求、试验方法、检验规则、标志、包装及贮存和质量承诺。 本标准适用于控制器与驱动电机为一体式的电泵，输送介质为清水或物理化学性质类似于清水的液体的智能永磁变频恒压离心电泵（以下简称“电泵”）。

Intelligent permanent magnet frequency conversion constant pressure centrifugal pump

ISO 20361:2019 液体泵和泵单元 - 噪声测试代码 - 精度等级2和3

This document specifies all the information necessary to carry out efficiently and under standardized conditions the determination, declaration, and verification of the airborne noise emission of liquid pumps or pump units (see 4.1). It specifies the noise measurement methods and the operating and mounting conditions that shall be used for the test. Noise emission characteristics include emission sound pressure levels at specified positions and the sound power level. The determination of these quantities is necessary for — declaring the noise emission values, and — purpose of noise control at source at the design stage. The determination of these quantities is also necessary for comparing the noise emitted by liquid pumps on the market. The use of this document ensures the reproducibility of the determination of the airborne noise- emission characteristics within specified limits determined by the grade of accuracy of the basic airborne noise measurement method used. Noise measurement methods according to this document are engineering methods (grade 2) and survey methods (grade 3). This document does not deal with the characterization of the structure-borne sound and liquid-borne noise generated by liquid pumps. NOTE This document is specified in EN 809+A1 for noise measurements of the pump (or pump unit).

Liquid pumps and pumps units — Noise test code — Grades 2 and 3 of accuracy

T/ZZB 1095-2019 电磁隔膜计量泵

本标准规定了电磁隔膜计量泵的术语和定义、信息确认、型式和基本参数、基本要求、技术要求、试验和检验、检验规则、标志、包装、贮存和质量承诺。 本标准适用于大气压86 kPa～106 kPa，温度-20 ℃～70 ℃，湿度30%RH～95%RH的环境条件下，输送温度为-15 ℃～85 ℃、粘度为0.3 mm2/s～200 mm2/s的不含固体颗粒的液体的电磁隔膜计量泵（以下简称“泵”）。

Electromagnetic diaphragm metering pump

BS EN ISO 14414:2019 泵系统能源评估

What is ISO 14414 - Pump system energy assessment about? ISO 14414 discusses pump system energy assessment. ISO 14414 sets the requirements for conducting and reporting the results of a pumping system energy assessment (hereafter referenced as “assessment”) that considers the entire pumping system, from energy inputs to the work performed as the result of these inputs. BS EN ISO 14414 is designed to be applied, to open and closed-loop pumping systems typically used at industrial, institutional, commercial, and municipal facilities, when requested. ISO 14414 is focused on assessing electrically driven pumping systems, which are dominant in most facilities, but is also applicable with other types of drivers, such as steam turbines and engines.   Note: ISO 14414 does not 

Pump system energy assessment

ISO/ASME 14414:2019 泵系统能量评估

Pump system energy assessment