23.100.20 缸 标准查询与下载

JIS B 8395:2017 流体动力系统和元件.气缸.往复运功用的活塞杆刮垢器环的外套.尺寸和公差

Fluid power systems and components -- Cylinder-rod wiper-ring housings in reciprocating applications -- Dimensions and tolerances

GSO ISO 6537:2016 气动流体动力系统 缸筒 有色金属管的要求

1.1 This International Standard defines the mechanical properties, dimensional tolerances, surface finishes and technical delivery conditions of the following tubes and bores for pneumatic fluid power cylinders : — round non-ferrous metallic tubes, seamless or welded type, in the as-drawn stress-relieved or fully heat-treated condition; — bores, specially finished, with or without metal removal. 1.2 The tubes covered by this International Standard are intended for use as barrels in a wide variety of pneumatic cylinders. NOTE — Brass and aluminium have been considered as a basis in this document but should not be considered the only materials suitable for such applications. 1.3 Annex A specifies the dimensions and tolerances on inside diameters for non-ferrous metallic pneumatic cylinder tubes. 1.4 Annex B provides a recommended method of ordering.

Pneumatic fluid power systems -- Cylinder barrels -- Requirements for non-ferrous metallic tubes

GSO ISO 21287:2016 气动流体动力 气缸 紧凑型气缸 1000 kPa (10 bar) 系列 孔径 20 mm 至 100 mm

This International Standard establishes a metric series of single rod pneumatic compact cylinders with bores of 20 mm to 100 mm for use of at maximum working pressure of 1 000 kPa (10 bar1)) with and without magnetic function. This series of pneumatic cylinder is not equipped with adjustable cushioning. Therefore, the application is restricted to those systems where adjustable cushioning is not required. Cylinders with bores of 20 mm and 25 mm can be used with end cover mountings in accordance with this International Standard. Cylinders with bores from 32 mm to 100 mm can be used with end cover mountings in accordance with ISO 15552. Piston rod mountings can be used for the different bores in accordance with ISO 8139 and ISO 8140.

Pneumatic fluid power -- Cylinders -- Compact cylinders, 1000 kPa (10 bar) series, bores from 20 mm to 100 mm

GSO ISO 10762:2016 液压流体动力 油缸安装尺寸 10 MPa（100 bar）系列

This International Standard establishes mounting dimensions for cylinders for use at 10 MPa [100 bar1)], as required for interchangeability of these cylinders. NOTE — This International Standard allows manufacturers of hydraulic equipment flexibility in the design of 10 MPa (100 bar) cylinders and does not restrict technical development; however, it does provide basic guidelines.

Hydraulic fluid power -- Cylinder mounting dimensions -- 10 MPa (100 bar) series

GSO ISO 6099:2016 流体动力系统和部件 气缸 安装尺寸和安装类型的识别代码

This International Standard establishes a convention for the identification of mounting dimensions and types used in the mounting of fluid power cylinders. It specifies a code for identifying cylinder mounting, envelope, accessory and connector dimensions, and for cylinder mounting and accessory types. This International Standard does not represent a standard list of all fluid power cylinder mounting and accessory types.

Fluid power systems and components -- Cylinders -- Identification code for mounting dimensions and mounting types

GSO ISO 13726:2016 液压流体动力 单杆油缸 16 MPa (160 bar) 紧凑型系列 孔径为 250 mm 至 500 mm 附件安装尺寸

This International Standard specifies the mounting dimensions required for interchangeability of accessories for 16 MPa (160 bar) compact cylinders conforming to ISO 6020-3. The accessories have been designed specifically for use with cylinders manufactured in accordance with ISO 6020-3, but this does not limit their application. This International Standard covers the following accessories: — AP2 – rod clevis, female thread (see Figure 1 and Table 1); — AP4 – rod eye, plain, female thread (see Figure 2 and Table 2); — AA4 - L – pivot pin (locking plate) (see Figure 3 and Table 3); — AL6 – locking plate for pivot pin (see Figure 4 and Table 4); — AA4 - S – pivot pin plain (see Figure 5 and Table 5). These accessories are used on hydraulic cylinders for mechanically transmitting the cylinder force. The design of these accessories is based on the maximum forces resulting from the specified internal diameters of the cylinders and pressures according to ISO 2944 and ISO 3320.

Hydraulic fluid power -- Single rod cylinders, 16 MPa (160 bar) compact series with bores from 250 mm to 500 mm -- Accessory mounting dimensions

ISO 16656:2016 液压传动.10MPa(100 bar)下用的缸径在32 mm 到 100 mm的单杆、短冲程气缸.安装尺寸

This International Standard establishes mounting dimensions for single rod short-stroke cylinders with bores from 32 mm to 100 mm for use at 10 MPa (100 bar) with or without magnetic functions, as required for interchangeability of these commonly used hydraulic cylinders. NOTE 1 This International Standard is intended to provide basic guidelines while allowing manufacturers of hydraulic equipment flexibility in the design of cylinders and not restricting technical development. NOTE 2 NOTE 3 The dimensions of these cylinders are most likely to require a minimum of space for mounting. 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2.

Hydraulic fluid power - Single rod, short-stroke cylinders with bores from 32 mm to 100 mm for use at 10 MPa (100 bar) - Mounting dimensions

BS ISO 16656:2016 液压传动.10MPa(100 bar)下使用的缸径在32mm到100mm的单杆、短冲程气缸.安装尺寸

Hydraulic fluid power. Single rod, short-stroke cylinders with bores from 32 mm to 100 mm for use at 10 MPa (100 bar). Mounting dimensions

BS PD ISO/TS 13725:2016 液压流体动力 液压缸屈曲载荷的评估方法

Hydraulic fluid power. Method for evaluating the buckling load of a hydraulic cylinder

ISO/TS 13725:2016 液压传动. 液压缸屈曲荷载的评估方法

Hydraulic fluid power - Method for evaluating the buckling load of a hydraulic cylinder

JB/T 12706.1-2016 液压传动 16MPa系列单杆缸的安装尺寸 第1部分:中型系列

JB/T 12706的本部分规定了16MPa系列中型单杆液压缸的米制安装尺寸，以满足常用液压缸的互换性要求。 本部分适用于缸径为25 mm~500 mm的圆头液压缸和缸径为200mm~500mm的方头液压缸。

Hydraulic fluid power.Mounting dimensions for single rod cylinders,16MPa series.Part 1: Medium series

DIN ISO 3320:2016 流体传动系统和部件.缸内径和活塞杆的直径和面积比.公制系列(ISO 3320:2013)

Fluid power systems and components - Cylinder bores and piston rod diameters and area ratios - Metric series (ISO 3320:2013)

GSO ISO 16656:2015 液压流体动力 缸径32毫米至100毫米的短行程单杆油缸 在10兆帕（100巴）压力下使用 安装尺寸

  Scope is not provided for this standard

Hydraulic fluid power -- Single rod, short-stroke cylinders with bores from 32 mm to 100 mm for use at 10 MPa (100 bar) -- Mounting dimensions

JIS B 8366-5:2015 流体动力系统和元件. 汽缸. 元素和识别码. 第5部分: 安装尺寸和安装类型的识别码

Fluid power systems and components -- Cylinders -- Elements and identification code -- Part 5: Identification code for mounting dimensions and mounting types

GSO ISO 10099:2015 气动流体容量 气缸 最终检验和验收标准

  Scope is not provided for this standard

Pneumatic fluid power -- Cylinders -- Final examination and acceptance criteria

GSO ISO 15552:2015 气动流体动力 带可拆卸安装件的气缸 1000 kPa (10 bar) 系列 孔径 32 mm 至 320 mm 基本、安装和附件尺寸

  Scope is not provided for this standard

Pneumatic fluid power -- Cylinders with detachable mountings, 1000 kPa (10 bar) series, bores from 32 mm to 320 mm -- Basic, mounting and accessories dimensions

BS ISO 4393:2015 液压动力系统和部件. 气缸. 活塞冲程的基本系列

Fluid power systems and components. Cylinders. Basic series of piston strokes

BS ISO 6020-3:2015 液压流体动力 16 MPa(160bar)系列单杆气缸的安装尺寸 孔径为 250mm 至 500mm 的紧凑型系列

Hydraulic fluid power. Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series. Compact series with bores from 250 mm to 500 mm

GSO ISO 4393:2015 流体动力系统及其组件 气缸 基本系列活塞的冲程

This International Standard specifies the preferred series of piston strokes for application to single-acting and doubleacting, hydraulic and pneumatic fluid power cylinders.

Fluid power systems and components -- Cylinders -- Basic series of piston strokes

GSO ISO 3320:2015 流体动力系统和元件缸孔和活塞杆孔的直径与面积之比标准系列

This International Standard establishes a metric series of cylinder bore and piston rod diameters for hydraulic and pneumatic cylinders, and specifies for each pair of diameters a corresponding standard ratio between the useful areas. This International Standard applies only to the dimensional criteria of products manufactured in conformity with this International Standard; it does not apply to their functional characteristics.

Fluid power systems and components -- Cylinder bores and piston rod diameters and area ratios -- Metric series