23.100.20 缸 标准查询与下载

GSO ISO 5597:2015 液压流体动力 气缸 往复应用中单作用活塞和杆密封件的外壳尺寸和公差

This International Standard establishes the preferred range of nominal dimensions and associated tolerances for a series of hydraulic cylinder rod and piston seal housings for reciprocating applications in the following range of dimensions: — cylinders from 16 mm to 500 mm; — rods from 6 mm to 360 mm. An additional range of seal housings is detailed in this International Standard to meet the reduced envelope requirements of the 160 bar (16 MPa)1) compact series of ISO 6020-2; these smaller section seals require stricter piston rod and cylinder bore tolerances. The range of dimensions is as follows: a) cylinders from 25 mm to 200 mm; b) rods from 12 mm to 140 mm. This International Standard does not give details of seal design, since the manner of construction of seals varies with each manufacturer. The design and material of the seal and any incorporated anti-extrusion component are determined by conditions such as temperature and pressure. This International Standard only applies to the dimensional criteria of products manufactured in conformity with this International Standard; it does not apply to their functional characteristics.

Hydraulic fluid power -- Cylinders -- Dimensions and tolerances of housings for single-acting piston and rod seals in reciprocating applications

GSO ISO 6195:2015 流体动力系统和部件 往复应用中缸杆上的扫描环外壳 尺寸和公差

This International Standard specifies dimensions and tolerances of housings for wiper rings used in reciprocating rod applications for fluid power cylinders. The range of rod diameters is from 4 mm to 360 mm. This International Standard is applicable to the following five housing designs. — Type A: recessed housings with undercut or separate cover to retain elastomeric wipers. — Type B: open recessed housings for wipers with integral rigid enforcement, that are press-fit in the housing. — Type C: recessed housings with undercut to retain elastomeric wipers (these are the preferred housings for double lip wipers without integral rigid enforcement). — Type D: recessed housings with undercut to retain elastomer-energized, plastic-faced wipers. — Type E: recessed housings with undercut or separate cover to retain elastomeric wipers (these are the preferred housings for single lip wipers without integral rigid enforcement). These housing designs are intended for use with the wiper rings according to Figure 1. This International Standard does not otherwise specify the style, configurations, materials, or performance ratings for the wiper ring.

Fluid power systems and components -- Cylinder-rod wiper-ring housings in reciprocating applications -- Dimensions and tolerances

GSO ISO 7425-2:2015 液压流体动力 弹性体供能、塑料面密封件的外壳 尺寸和公差 第2部分：杆密封外壳

This part of ISO 7425 specifies the dimensions and associated tolerances for a series of hydraulic cylinder rod seal housings to accommodate elastomer-energized, plastic-faced seals used in reciprocating applications. It is not the intention of this part of ISO 7425 to stipulate details of seal design, since the manner of construction of seals varies with each manufacturer. The design and material of the seal and any incorporated anti-extrusion component are determined by conditions such as temperature and pressure. This part of ISO 7425 applies only to the dimensional characteristics of products manufactured in accordance with this part of ISO 7425. It does not apply to their functional characteristics.

Hydraulic fluid power -- Housings for elastomer-energized, plastic-faced seals -- Dimensions and tolerances -- Part 2: Rod seal housings

GSO ISO 10766:2015 液压油容量气缸活塞和连杆用截头矩形截面轴承环的外壳尺寸

This International Standard specifies the preferred range of nominal dimensions and associated tolerances for a series of hydraulic cylinder piston and rod housings for rectangular-section-cut bearing rings, of the type shown in Clause 5, for applications in the following range of dimensions: — for cylinders with bores of 16 mm to 500 mm, inclusive; — for rods with diameters of 12 mm to 450 mm, inclusive. This International Standard does not give details of cut bearing ring design, because the manner of construction of cut bearing rings varies with each manufacturer. The design material of cut bearing rings is determined by conditions such as the temperature, pressure and side load on the cylinder to which they are fitted.

Hydraulic fluid power -- Cylinders -- Housing dimensions for rectangular-section-cut bearing rings for pistons and rods

GSO ISO 4395:2015 流体动力系统和部件气缸杆端类型和尺寸

This International Standard establishes a basic series for piston rod end types for application on cylinders used in hydraulic and pneumatic fluid power systems. It specifies thread dimensions and configurations for use with hydraulic and pneumatic cylinder piston rod ends, as well as the dimensions of wrench flats and hook wrench holes that are sometimes necessary for the assembly of the cylinder piston rod’s threaded end to accessories.

Fluid power systems and components -- Cylinder piston rod end types and dimensions

GSO ISO 3321:2015 流体动力系统和部件 缸孔和活塞杆直径 英制系列

This International Standard establishes an inch series of cylinder bores and piston rod diameters for application to hydraulic and pneumatic fluid power cylinders.

Fluid power systems and components -- Cylinder bores and piston rod diameters -- Inch series

GSO ISO 6547:2015 液压流体动力 气缸 包含轴承套的活塞密封外壳 尺寸和公差

1.1 This International Standard establishes the dimensions and associated tolerances for a series of housings for hydraulic cylinder piston seals that incorporate bearing rings. 1.2 It specifies the dimensions for a range of seal housings for cylinders of 25 to 500 mm. 1.3 It is not the intention of this International Standard to set forth details of seal design, since the manner of construction of seals varies with each manufacturer. The design and material of the seal and the incorporated bearing rings are determined by conditions such as temperature and pressure. 1.4 It applies to piston-heads that may be either assembled from a number of components or made in one piece.

Hydraulic fluid power -- Cylinders -- Piston seal housings incorporating bearing rings -- Dimensions and tolerances

GSO ISO 7425-1:2015 液压流体动力 弹性体供能、塑料面密封件的外壳 尺寸和公差 第1部分：活塞密封外壳

This part of ISO 7425 specifies the dimensions and associated tolerances for a series of piston seal housings to accommodate elastomer-energized, plastic-faced seals used in reciprocating applications. It is not the intention of this part of ISO 7425 to stipulate details of seal design, since the manner of construction of seals varies with each manufacturer. The design and material of the seals and any associated anti-extrusion components are determined by conditions such as temperature and pressure. This part of ISO 7425 applies only to the dimensional characteristics of products manufactured in accordance with this part of ISO 7425. It does not apply to their functional characteristics.

Hydraulic fluid power -- Housings for elastomer-energized, plastic-faced seals -- Dimensions and tolerances -- Part 1: Piston seal housings

ISO 4393:2015 流体传动系统和元件 缸筒 活塞行程基本系列

This International Standard specifies the preferred series of piston strokes for application to singleacting and double-acting fluid power cylinders. These strokes are mainly used for pneumatic cylinders but may also be used for hydraulic cylinders.

Fluid power systems and components - Cylinders - Basic series of piston strokes

BS ISO 6432:2015 气动流体动力.单杆汽缸.1100kPa(10bar)系列.8-25mm的汽缸内径.基本和安装尺寸

Pneumatic fluid power. Single rod cylinders, 1 000 kPa (10 bar) series, bores from 8 mm to 25 mm. Basic and mounting dimensions

BS ISO 6020-2:2015 液压流体动力.16MPa(160bar)系列单杆汽缸用安装尺寸.小型系列

Hydraulic fluid power. Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series. Compact series

ISO 6020-2:2015 液压传动.单杆缸安装尺寸,16 MPa(160 bar)系列.第2部分:小型系列

This part of ISO 6020 establishes metric mounting dimensions for compact series cylinders, 16 MPa [160 bar1)], as required for interchangeability of commonly-used hydraulic cylinders. NOTE 1 This part of ISO 6020 allows manufacturers of hydraulic equipment flexibility in the design of metric cylinders and does not restrict technical development; however, it does provide basic guidelines. NOTE 2 The compact series dimensions are most applicable to square head cylinders.

Hydraulic fluid power - Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series - Part 2: Compact series

ISO 6432:2015 气压传动 单杆缸1000 kPa(10 bar)系列 缸内径8mm～25mm.基本尺寸和安装尺寸

This International Standard establishes a metric series of mounting dimensions required for interchangeability of commonly used pneumatic cylinders for a maximum working pressure of 1000 kPa (10 bar). NOTE This International Standard allows manufacturers freedom of design in metric cylinders and does not restrict technical development but provides basic guidelines.

Pneumatic fluid power - Single rod cylinders, 1000 kPa (10 bar) series, bores from 8 mm to 25 mm - Basic and mounting dimensions

ISO 6020-3:2015 液压传动 单杆缸安装尺寸,16 MPa(160 bar)系列 第3部分:缸内径250mm～500mm的小型系列

This part of ISO 6020 establishes metric mounting dimensions for single rod compact series hydraulic cylinders with bores from 250 mm to 500 mm for use at 16 MPa (160 bar1)), as required for interchangeability of commonly used hydraulic cylinders. NOTE 1 This part of ISO 6020 allows manufacturers of hydraulic equipment flexibility in the design of metric cylinders and does not restrict technical development, but does provide basic guidelines. NOTE 2 The compact series dimensions are most applicable to square-head cylinders. This part of ISO 6020 applies only to the dimensions of manufactured products. It does not apply to their functional characteristics.

Hydraulic fluid power - Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series - Part 3: Compact series with bores from 250 mm to 500 mm

BS ISO 10762:2015 液压传动. 10 MPa (100 bar) 系列汽缸的安装尺寸

Hydraulic fluid power. Mounting dimensions for cylinders, 10 MPa (100 bar) series

ISO 10762:2015 液压传动. 10 MPa (100 bar) 系列汽缸的安装尺寸

This International Standard establishes mounting dimensions for cylinders for use at 10 MPa [100 bar1)], as required for interchangeability of these cylinders. NOTE This International Standard allows manufacturers of hydraulic equipment flexibility in the design of 10 MPa (100 bar) cylinders and does not restrict technical development; however, it does provide basic guidelines.

Hydraulic fluid power - Mounting dimensions for cylinders, 10 MPa (100 bar) series

NF E48-501:2015 液压流体动力 单杆液压缸附件的安装尺寸，16 MPa（160 bar）介质和 25 MPa（250 bar）系列

La présente Norme internationale spécifie les dimensions nécessaires à l'interchangeabilité des accessoires pour vérins 16 MPa [160 bar] série moyenne conformes à l'ISO 6020-1 et pour vérins 25 MPa (250 bar), conformes à l'ISO 6022. Les accessoires ont été spécialement conçus pour être utilisés sur les vérins fabriqués conformément à l'ISO 6020-1 et à l'ISO 6022, mais ne se limitent pas à cette application.

Hydraulic fluid power - Mounting dimensions for accessories for single rod cylinders, 16 MPa (160 bar) medium and 25 MPa (250 bar) series

NF E48-503*NF ISO 8133:2015 液压流体动力 单杆液压缸附件的安装尺寸，16 MPa（160 bar）紧凑型系列

La présente Norme internationale spécifie les dimensions nécessaires à l'interchangeabilité des accessoires pour vérins 16 MPa [160 bar] série compacte conformes à l'ISO 6020-2. Les accessoires ont été spécialement conçus pour être utilisés sur les vérins fabriqués conformément à l'ISO 6020-2, mais ne se limitent pas à cette application.

Hydraulic fluid power - Mounting dimensions for accessories for single rod cylinders, 16 MPa (160 bar) compact series

KS B 6704-2014 气压缸.安装尺寸

Pneumatic cylinders — Mounting dimensions

BS ISO 8132:2014 液压流体动力. 16 MPa (160 bar) 中型和25 MPa (250 bar) 系列单杆汽缸附件的安装尺寸

Hydraulic fluid power. Mounting dimensions for accessories for single rod cylinders, 16 MPa (160 bar) medium and 25 MPa (250 bar) series