23.100.40 管道和管接头 标准查询与下载

BS ISO 8434-6:2009 液压及通用金属管接头.带或不带O形密封环的60度圆锥体连接头

Metallic tube connections for fluid power and general use - 60 ° cone connectors with or without O-ring

DIN EN ISO 6803:2010 橡胶和塑料软管及软管组件.无弯曲液压压力脉冲试验(ISO 6803-2008).德文版本EN ISO 6803-2008

This International Standard describes two categories of hose impulse testing without flexing for rubber or plastic hose assemblies. Category 1 is high pressure testing for test pressures greater than 3 MPa and Category 2 is for test pressures from 1, 5 MPa through 3 MPa. The test procedure is applicable to hydraulic hose assemblies that are subject to pulsating pressures in service and are contained within the product requirements.

Rubber or plastics hoses and hose assemblies - Hydraulic-pressure impulse test without flexing (ISO 6803:2008); German version EN ISO 6803:2008

GOST R ISO 23309-2010 液压动力系统.组装系统.冲洗清洁线方法

Hydraulic fluid power systems. Assembled systems. Methods of cleaning lines by flushing

SAE J516-2009 液压软管配件

This SAE Standard provides general and dimensional specifications for the most common hose fittings used in conjunction with hydraulic hoses specified in SAE J517 and utilized in hydraulic systems on mobile and stationary equipment. The general specifications contained in Sections 1 through 15 are applicable to all hydraulic hose fittings and supplement the detailed specifications for the 100R-series fittings contained in the later sections of this document. This document shall be utilized as a procurement document only to the extent agreed upon by the manufacturer and user. Refer to SAE J517 for specifications of hose and information on hose assemblies. SAE J1273 contains information on application factors affecting hose fittings, hose, and hose assemblies. THE RATED WORKING PRESSURE OF A HOSE ASSEMBLY COMPRISING SAE J516 FITTINGS AND SAE J517 HOSE SHALL NOT EXCEED THE LOWER OF THE TWO WORKING PRESSURE RATED VALUES.

Hydraulic Hose Fittings

DIN EN ISO 8434-1 Berichtigung 1:2009 液压传动和一般用途的金属管连接件.第1部分:24度锥形连接件(ISO 8434-1-2007).德文版本EN ISO 8434-1-2007,DIN EN ISO 8434-1-2008-02标准的勘误表.德文版本EN ISO 8434-1-2007/AC-2009

Metallic tube connections for fluid power and general use - Part 1: 24 degree cone connectors (ISO 8434-1:2007); German version EN ISO 8434-1:2007, Corrigendum to DIN EN ISO 8434-1:2008-02; German version EN ISO 8434-1:2007/AC:2009

DIN EN ISO 19879 Berichtigung 1:2009 液力及一般用途金属管连接件.液压传动连接件的试验方法(ISO 19879-2005).德文版本EN ISO 19879-2005,DIN EN ISO 19879-2005-10的勘误表.德文版本EN ISO 19879-2005/AC-2009

Metallic tube connections for fluid power and general use - Test methods for hydraulic fluid power connections (ISO 19879:2005); German version EN ISO 19879:2005, Corrigendum to DIN EN ISO 19879:2005-10; German version EN ISO 19879:2005/AC:2009

SAE J2833-2009 弯曲双扩口消除应力,焊接冷拉高强度(690 MPa抗拉强度)低合金钢液压管路

This specification covers sub-critically annealed electric resistance welded and cold-drawn single-wall high strength low alloy steel tubing intended for use in hydraulic pressure lines and in other applications requiring tubing of a quality suitable for bending, flaring, cold forming, welding and brazing. The grade of material produced to this specification is of micro-alloy content and is considerably stronger and intended to service higher pressure applications using thinner walls than like sizes of the grades of material specified in SAE J525, SAE J2467 and SAE J2614. Due to the alloy content of the material, the forming characteristics of the finished tube are equal to or better, when compared to SAE J525, SAE J2467 and SAE J2614. Nominal reference working pressures for this tubing are listed in ISO 10763 and SAE J1065. Caution: When brazing or welding is used as a tube end joining method, the structural integrity of the tube material can potentially be compromised due to the degradation of the areas affected by the thermal effect applied to the tubing; therefore, the ISO 10763 and SAE J1065 nominal reference working pressures may not be applicable. Brazed and/or welded tube assembly configurations made to specific geometry and components bill of material in association with this material, may require qualification testing in accordance with ISO 19879 Test Methods for Hydraulic Fluid Power Connections. Cold forming the tube end configurations avoids this systemic testing by not compromising the tube material structural integrity.

Welded and Cold-Drawn, High Strength (690 MPa Tensile Strength) Low Alloy Steel Hydraulic Tubing, Stress Relieved Annealed for Bending and Flaring

ISO 8434-6:2009 液体动力和通用金属导管接头.第6部分:有或无O形密封圈的60°锥形接头

Metallic tube connections for fluid power and general use - Part 6: 60° cone connectors with or without O-ring

LST EN ISO 8434-1:2007/AC:2009 流体动力和一般用途的金属管连接 第1部分：24 度锥形连接器（ISO 8434-1:2007）

Metallic tube connections for fluid power and general use - Part 1: 24 degree cone connectors (ISO 8434-1:2007)

DS/EN ISO 8434-1:2009 流体动力和一般用途的金属管接头 第1部分：24 度锥形接头

This part of ISO 8434 specifies the general and dimensional requirements for 24° cone connectors using cutting ring and O-ring seal cone (referred to as DKO) suitable for use with ferrous and non-ferrous tubes with outside diameters from 4 mm to 42 mm inclusive. These connectors are for use in fluid power and general applications within the limits of pressure and temperature specified in this part of ISO 8434.They are intended for the connection of plain end tubes and hose fittings to ports in accordance withISO 6149-1, ISO 1179-1 and ISO 9974-1. (See ISO 12151-2 for related hose fitting specification.)These connectors provide full-flow connections in hydra

Metallic tube connections for fluid power and general use - Part 1: 24 degree cone connectors

BS ISO 1436:2009 橡胶软管和软管组件.油质或水质流体用金属丝编织增强液压型管.规范

Rubber hoses and hose assemblies - Wire-braid-reinforced hydraulic types for oil-based or water-based fluids - Specification

BS ISO 4079:2009 橡胶软管和软管组件.油质或水质流体用织物增强液压型管.规范

Rubber hoses and hose assemblies - Textile-reinforced hydraulic types for oil-based or water-based fluids - Specification

ISO 4079:2009 橡胶软管和软管组件.油基或水基流体用织物增强液压型.规范

This International Standard specifies requirements for five types of textile-reinforced hydraulic hose and hose assembly of nominal size from 5 to 100. They are suitable for use with water-based hydraulic fluids HFC, HFAE, HFAS and HFB as defined in ISO 6743-4 at temperatures ranging from −40 °C to +60 ºC or oil-based hydraulic fluids HH, HL, HM, HR and HV as defined in ISO 6743-4 at temperatures ranging from −40 °C to +100 °C. This International Standard does not include requirements for end fittings. It is limited to requirements for hoses and hose assemblies. NOTE It is the responsibility of the user, in consultation with the hose manufacturer, to establish compatibility of the hose with the fluid to be used.

Rubber hoses and hose assemblies - Textile-reinforced hydraulic types for oil-based or water-based fluids - Specification

ISO 3862:2009 橡胶软管和软管组件.油基或水基流体用橡胶包皮螺旋钢丝增强液压型.规范

This International Standard specifies requirements for five types of spiral-wire-reinforced hydraulic hose and hose assembly of nominal size from 6,3 to 51. They are suitable for use with water-based hydraulic fluids HFC, HFAE, HFAS and HFB as defined in ISO 6743-4 at temperatures ranging from −40 °C to +60 °C and oil-based hydraulic fluids HH, HL, HM, HR and HV as defined in ISO 6743-4 at temperatures ranging from −40 °C to +100 °C for types 4SP and 4SH and −40 °C to +120 °C for types R12, R13 and R15. NOTE 1 This temperature rating is related to the water-based hydraulic fluids defined in ISO 6743-4. This International Standard does not include requirements for end fittings. It is limited to requirements for hoses and hose assemblies. NOTE 2 It is the responsibility of the user, in consultation with the hose manufacturer, to establish the compatibility of the hose with the fluid to be used.

Rubber hoses and hose assemblies - Rubber-covered spiral-wire-reinforced hydraulic types for oil-based or water-based fluids - Specification

ISO 1436:2009 橡胶软管和软管组件.油基或水基液体用金属丝编织增强液压型.规范

This International Standard specifies requirements for six types of wire-braid-reinforced hose and hose assembly of nominal size from 5 to 51 plus, for one of the five types (type R2ATS), nominal size 63. They are suitable for use with water-based hydraulic fluids HFC, HFAE, HFAS and HFB as defined in ISO 6743-4 at temperatures ranging from to −40 °C to +60 °C or oil-based hydraulic fluids HH, HL, HM, HR and HV as defined in ISO 6743-4 at temperatures ranging from −40 °C to +100 °C. This International Standard does not include requirements for end fittings. It is limited to requirements for hoses and hose assemblies. NOTE It is the responsibility of the user, in consultation with the hose manufacturer, to establish the compatibility of the hose with the fluid to be used.

Rubber hoses and hose assemblies - Wire-braid-reinforced hydraulic types for oil-based or water-based fluids - Specification

BS EN ISO 1179-3:2009 通用和液压传动用连接件 带弹性体密封件或金属对金属密封件的ISO 228-1螺纹端口和螺柱端头 带扣环O型密封圈（G型和H型）密封的轻型（L系列）螺柱端头

Connections for general use and fluid power. Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing. Light-duty (L series) stud ends with sealing by O-ring with retaining ring (types G and H)

BS EN ISO 1179-2:2009 通用和液压传动用连接件 带弹性体密封件或金属对金属密封件的ISO 228-1螺纹端口或螺柱端头 带弹性体密封件（E型）的重型（S系列）和轻型（L系列）螺柱端头

Connections for general use and fluid power. Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing. Heavy-duty (S series) and light-duty (L series) stud ends with elastomeric sealing (type E)

BS EN ISO 1179-1:2009 通用和液压传动用连接件 带弹性体密封件或金属对金属密封件的ISO 228-1螺纹端口和螺柱端头 螺纹端口

Connections for general use and fluid power. Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing. Threaded ports

BS EN ISO 1179-4:2009 通用和液压传动用连接件 带弹性体密封件或金属对金属密封件的ISO 228-1螺纹端口和螺柱端头 通用只带金属对金属密封件（B型）的螺柱端头

Connections for general use and fluid power. Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing. Stud ends for general use only with metal-to-metal sealing (type B)

BS EN ISO 1179-3:2008 通用和液压传动用连接件.带弹性体密封件或金属对金属密封件的ISO 228-1螺纹端口和螺柱端头.带扣环O型密封圈(G型和H型)密封的轻型(L系列)螺柱端头

This part of ISO 1179 specifies dimensions, performance requirements and test procedures for non-adjustable and adjustable light-duty (L series) stud ends with ISO 228-1 threads with sealing by O-ring with retaining ring (types G and H, respectively). Light-duty (L series) stud ends in accordance with this part of ISO 1179 may be used at working pressures up to 31,5 MPa (315 bar) for non-adjustable stud ends (type G) and up to 20 MPa (200 bar) for adjustable stud ends (type H). The permissible working pressure depends upon size, materials, design, working conditions, application, etc. Conformance to the dimensional information in this part of ISO 1179 does not guarantee rated performance. Each manufacturer shall perform testing according to the specification contained in this part of ISO 1179 to assure that components made to this part of ISO 1179 comply with the performance ratings.

Connections for general use and fluid power - Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing - Light-duty (L series) stud ends with sealing by O-ring with retaining ring (types G and H)