23.100.40 管道和管接头 标准查询与下载

UL 1469-2006 回流专用止回阀的阀身强度和液压损失率试验

These requirements cover backflow special check valves of 3/4-inch (19.1-mm) through 10-inch (254-mm) nominal pipe size used in piping systems supplying water for fire protection service. The backflow special check valves covered by these requirements are intended for installation and use in accordance with the Standards for: a) Low Expansion Foam and Combined Agent Systems, NFPA 11; b) Installation of Sprinkler Systems, NFPA 13; c) Installation of Standpipe and Hose Systems, NFPA 14; d) Water Spray Fixed Systems for Fire Protection, NFPA 15; e) Deluge Foam-Water Sprinkler and Spray Systems, NFPA 16; f) Installation of Centrifugal Fire Pumps, NFPA 20; g) Water Tanks for Private Fire Protection, NFPA 22; and h) Installation of Private Fire Service Mains and Their Appurtenances, NFPA 24. A product that contains features, characteristics, components, materials, or systems new or different from those covered by the requirements in this standard and that involve a risk of fire, electric shock, or injury to persons shall be evaluated using the appropriate additional component and end-product requirements as determined necessary to maintain the acceptable level of safety as originally anticipated by the intent of this standard. A product whose features, characteristics, components, materials, or systems conflict with specific requirements or provisions of this standard cannot be judged to comply with this standard. Where considered appropriate, revision of requirements shall be proposed and adopted in conformance with the methods employed for development, revision, and implementation of this standard.

UL Standard for Safety Strength of Body and Hydraulic Pressure Loss Testing of Backflow Special Check Valves Second Edition

KS B ISO 15171-1-2005(2010) 流体动力和通用连接诊断用液力偶合器第1部分:非压力连接用偶合器

Connections for fluid power and general use－Hydraulic couplings for diagnostic purposes－Part 1：Coupling not for connection under pressure

KS B ISO 15171-2-2005(2010) 流体动力和通用连接诊断用液力偶合器第2部分:带M16×2端压力连接的偶合器

Connections for fluid power and general use－Hydraulic couplings for diagnostic purposes－Part 2：Coupling with M16×2 end for connection under pressure

NF E49-052*NF ISO 16030:2005 气压传动.连接.气口和螺柱端

Pneumatic fluid power - Connections - Ports and stud ends.

ISO 4079-2:2005 橡胶软管和软管组件.织物增强液压型.规范.第2部分:水基流体的应用

This part of ISO 4079 specifies requirements for five types of textile-reinforced hydraulic hoses and hose assemblies of nominal size from 5 to 100. They are suitable for use with hydraulic fluids HFC, HFAE, HFAS and HFB as defined in ISO 6743-4 at temperatures ranging from - 40 ℃ to + 60 ℃. This part of ISO 4079 does not include requirements for end fittings. It is limited to requirements for hoses and hose assemblies. NOTE It is the responsibility of the user, in consultation with the hose manufacturer, to establish compatibility of the hose with the fluid to be used.

Rubber hoses and hose assemblies - Textile-reinforced hydraulic types - Specification - Part 2: Water-based fluid applications

BS ISO 8434-3:2005 用于液压传动和一般用途的金属管接头.O形圈端面密封管接头

This part of ISO 8434 specifies the general and dimensional requirements for the design and performance of O-ring face seal connectors made of steel for tube outside diameters or hose inside diameters of 6 mm through 38 mm, inclusive. These connectors are for use in fluid power and general applications where elastomeric seals can be used to prevent fluid leakage, including leakage caused by variations in assembly procedures. They are intended for the connection of tubes and hose fittings to ports in accordance with ISO 6149-1. (See ISO 12151-1 for related hose fitting specification.) These connectors provide leakproof, full-flow connections in hydraulic systems operating from a vacuum of 6,5 kPa [0,065 bar 3)] absolute pressure to the working pressures shown in Table 1. Because many factors influence the pressure at which a system performs satisfactorily, these values shall not be understood as guaranteed minimums. For every application, it is recommended that sufficient testing be conducted and reviewed by both the user and manufacturer to ensure that required performance levels are met. NOTE For use under conditions outside the pressure and/or temperature limits specified, see 5.3. Both metric and inch tubing can be accommodated by changing the sleeve (see Annex D). In the past, these connectors have been used predominantly with inch tubing. For new and future designs, the use of metric tubing is preferred. This part of ISO 8434 also specifies a performance and qualification test for O-ring face seal connectors.

Metallic tube connections for fluid power and general use - O-ring face seal connectors

ISO 19879:2005 液压和一般用途用金属管连接件.液压传动连接件的试验方法

This International Standard specifies uniform methods for the testing and performance evaluation of metallic tube connections, stud ends for ports and flange connections for use in hydraulic fluid power applications. This International Standard does not apply to the testing of hydraulic quick-action couplings, which is covered by ISO 7241-2. Tests outlined in this International Standard are independent of each other and document the method to follow for each test. See the appropriate component International Standard for which tests to conduct and for performance criteria. For qualification of the connector, the minimum number of samples specified in this International Standard are tested, unless otherwise specified in the relevant connector standard or as agreed upon by the manufacturer and the user.

Metallic tube connections for fluid power and general use - Test methods for hydraulic fluid power connections

SAE J516-2005 液压软管配件

This SAE Standard provides general and dimensional specifications for the most common hose fittings used in conjunction with hydraulic hoses specified in SAE J517 and utilized in hydraulic systems on mobile and stationary equipment. The general specifications contained in Sections 1 through 15 are applicable to all hydraulic hose fittings and supplement the detailed specifications for the 100R-series fittings contained in the later sections of this document. This document shall be utilized as a procurement document only to the extent agreed upon by the manufacturer and user. Refer to SAE J517 for specifications of hose and information on hose assemblies. SAE J1273 contains information on application factors affecting hose fittings, hose, and hose assemblies. THE RATED WORKING PRESSURE OF A HOSE ASSEMBLY COMPRISING SAE J516 FITTINGS AND SAE J517 HOSE SHALL NOT EXCEED THE LOWER OF THE TWO WORKING PRESSURE RATED VALUES.

Hydraulic Hose Fittings

ISO 8434-3:2005 用于流体传动和一般用途的金属管接头.第3部分:O形圈端面密封管接头

This part of ISO 8434 specifies the general and dimensional requirements for the design and performance of O-ring face seal connectors made of steel for tube outside diameters or hose inside diameters of 6 mm through 38 mm, inclusive. These connectors are for use in fluid power and general applications where elastomeric seals can be used to prevent fluid leakage, including leakage caused by variations in assembly procedures. They are intended for the connection of tubes and hose fittings to ports in accordance with ISO 6149-1. (See ISO 12151-1 for related hose fitting specification.) These connectors provide leakproof, full-flow connections in hydraulic systems operating from a vacuum of 6,5 kPa [0,065 bar 3)] absolute pressure to the working pressures shown in Table 1. Because many factors influence the pressure at which a system performs satisfactorily, these values shall not be understood as guaranteed minimums. For every application, it is recommended that sufficient testing be conducted and reviewed by both the user and manufacturer to ensure that required performance levels are met. NOTE For use under conditions outside the pressure and/or temperature limits specified, see 5.3. Both metric and inch tubing can be accommodated by changing the sleeve (see Annex D). In the past, these connectors have been used predominantly with inch tubing. For new and future designs, the use of metric tubing is preferred. This part of ISO 8434 also specifies a performance and qualification test for O-ring face seal connectors.

Metallic tube connections for fluid power and general use - Part 3: O-ring face seal connectors

NF E49-053:2005 气压传动.最高工作压力为10 bar、16 bar和25 bar(1 MPa、1.6 MPa和2.5 MPa)圆柱形快速接头.插头连接尺寸、规范、应用指南和试验

Pneumatic fluid power - Cylindrical quick-action couplings for maximum working pressures of 10 bar, 16 bar and 25 bar (1 MPa, 1,6 MPa and 2,5 MPa) - Plug connecting dimensions, specifications, application guidelines and testing.

ISO 16030:2001/Amd 1:2005 气压传动.连接.气口和双头螺栓端.修改件1

本标准规定了气压传动用圆柱螺纹的气口和螺柱端的尺寸和性能要求。 本标准规定了用于自- 90 kPa～1.6 MPa压力范围内防泄漏连接的可重复使用的、有效保压的密 封装置。 本标准适用于在气压传动中新设计的螺纹气n和螺柱端。

Pneumatic fluid power - Connections - Ports and stud ends; Amendment 1

KS B ISO 16028-2004(2009) 20∼31.5MPa压力下使用的液压传动-平齐面式快接管接头-规格

Hydraulic fluid power－Flush－face type, quick－action couplings for use at pressures of 20∼31.5 MPa－Specifications

KS B ISO 9974-1-2004(2009) 一般用途和流体动力的连接 - 具有ISO 261螺纹的弹性或金属对金属密封的端口和螺柱端:第1部分螺纹端口

Connections for general use and fluid power Ports and stud ends with ISO 261 threads with elastomeric or metal to metal sealing - Part 1 Threaded ports

KS B ISO 6162-1-2004(2019) 液压传动带分体式或整体式法兰夹和公制或英制螺钉的法兰连接器第1部分:压力为3.5MPa至35MPa DN13至DN127的法兰连接器

Hydraulic fluid power－Flange connectors with split or one-piece flange clamps and metric or inch screws－Part 1：Flange connectors for use at pressures of 3.5 MPa to 35 MPa, DN13 to DN127

KS B ISO 6162-2:2004 液压传动.带分离式或一体式法兰夹和米制或英制螺纹的凸缘连接器.第2部分:压力为35MPa至40MPa(350巴至400巴)、DN13.DN51时使用的凸缘连接器

이 규격은 35∼40 MPa의 압력에서 사용하는 플랜지 헤드, 스플릿 플랜지 클램프(F

Hydraulic fluid power－Flange connectors with split or one-piece flange clamps and metric or inch screws－Part 2：Flange connectors for use at pressures of 35MPa to 40MPa, DN13 to DN51

KS B ISO 6150:2004 气压传动.最大工作压力为10巴、16巴和25巴(1MPa、1.6MPa和2.5MPa)圆形快速连接插塞尺寸;规范、应用指南和试验

이 규격은 공압 신속 작동 커플링 플러그의 상호 교환성을 보장하기 위한 치수와 공차에

Pneumatic fluid power-Cylindrical quick-action couplings for maximum working pressures of 1 MPa, 1.6 MPa and 2.5 MPa-Plug connecting dimensions, specifications, application guidelines and testing

KS B ISO 7241-2-2004(2009) 液压传动快接管接头第2部分:试验方法

Hydraulic fluid power－Quick-action couplings－Part 2：Test methods

KS B ISO 6162-1:2004 液压传动.带分离式或一体式法兰夹和米制或英制螺纹的凸缘连接器.第1部分:压力为3.5MPa至35MPa(35巴至350巴)、DN.13.DN.127时使用的凸缘连接器

이 규격은 3.5∼35 MPa의 압력에서 사용하는 플랜지 헤드, 스플릿 플랜지 클램프(

Hydraulic fluid power－Flange connectors with split or one-piece flange clamps and metric or inch screws－Part 1：Flange connectors for use at pressures of 3.5 MPa to 35 MPa, DN13 to DN127

KS B ISO 6150-2004(2019) 气动流体动力－最大工作压力为1MPa、1.6MPa和2.5MPa的圆柱形快接管接头－插塞连接尺寸、规范、应用指南和试验

Pneumatic fluid power－Cylindrical quick-action couplings for maximum working pressures of 1 MPa, 1.6 MPa and 2.5 MPa－Plug connecting dimensions, specifications, application guidelines and testing

KS B ISO 7241-1-2004(2009) 液压传动 快速接头操作 - 第1部分:尺寸和细节要求

Hydraulic fluid power－Quick-action couplings－Part 1：Dimensions and requirements