23.100.40 管道和管接头 标准查询与下载

KS B ISO 11926-3-2003(2008) 一般用途和流体动力连接带英制螺纹和O形密封圈的端口和螺柱端第3部分:轻型（L系列）螺柱端

Connections for general use and fluid power－Ports and stud ends with inch threads and O-ring sealing－Part 3：Light-duty(L series) stud ends

KS B ISO 11926-2-2003(2008) 通用和流体动力连接ISO 725螺纹和O形密封圈的端口和螺柱端第2部分:重型（S系列）螺柱端

Connections for general use and fluid power－Ports and stud ends with ISO 725 threads and O-ring sealing－Part 2：Heavy-duty(S series) stud ends

DIN 20043:2003 液压传动循环管路用U形锁扣连接件

This standard applies for staple-lock couplings which generally are used for the connection of hydraulic hose assemblies according to DIN EN 853 and DIN EN 856.

Staple-lock couplings for hydraulic power-transmission circuits

BS ISO 6605:2003 液压传动.软管及软管组件.试验方法

This International Standard specifies uniform test methods for evaluating the performance of hoses and hose assemblies (hoses and attached hose fittings) used in hydraulic fluid power systems. Specific tests and performance criteria for evaluating hoses and hose assemblies used in hydraulic applications are in accordance with the requirements of the respective product (hoses or hose fitting) specifications.

Hydraulic fluid power - Hoses and hose assemblies - Test methods

LST ISO 7241-2:2003 液压流体动力 快速联轴器 第2部分：测试方法（idt ISO 7241-2:2000）

Hydraulic fluid power. Quick-action couplings. Part 2: Test methods (idt ISO 7241-2:2000)

DIN 20044:2003 液压动力传输管路用S型钩环锁定联接器.尺寸、要求和试验

The document applies for staple-lock couplings which generally are used for the connection of hydraulic hose assemblies according DIN EN 856.

Staple-lock couplings type S for hydraulic power-transmission circuits - Dimensions, requirements, testing

KS B ISO 4397-2002(2012) 流体动力系统和部件连接器和相关部件管子的公称外径和软管的公称内径

Fluid power systems and components－connectors and associated components－Nominal outside diameters of tubes and nominal inside diameters of hoses

ISO 6162-2:2002 液压传动.带分离式或一体式法兰夹和米制或英制螺纹的凸缘连接器.第2部分:压力为35MPa至40MPa(350巴至400巴)、DN 13-DN 51时使用的凸缘连接器

This part of ISO 6162 specifies complete general and dimensional characteristics for flange heads, split flange clamps (FCS), one-piece flange clamps (FC) and ports applicable to four-screw, split and one-piece flange clamp type tube and hose connectors for use at pressures of 35 MPa (350 bar) to 40 MPa (400 bar). It also specifies the dimensions of the seals to be used, as well as the grooves to house the seal. This part of ISO 6162 also recognizes the need to accommodate metric (type 1) screw fasteners, as well as to provide a means to use existing inch (type 2) screw fasteners. These connectors are intended for application in hydraulic systems on industrial and commercial products, where it is desired to avoid the use of threaded connectors. Surges of pressure higher than the nominal ratings will reduce the ability of the flange connectors to retain the hydraulic fluid. This should be taken into account in the design of the hydraulic system. note: 1) 1 bar = 0,1 MPa = 10 Pa; 1 Pa = 1 N/m.

Hydraulic fluid power - Flange connectors with split or one-piece flange champs and metric or inch screws - Part 2: Flange connectors for use at pressures of 35 MPa (350 bar) to 40 MPa (400 bar), DN 13 to DN 51

ISO 6162-1:2002 液压传动.带分离式或一体式法兰夹和米制或英制螺纹的凸缘连接器.第1部分:压力为3.5MPa至35MPa(35巴至350巴)、DN 13-DN 127时使用的凸缘连接器

This part of ISO 6162 specifies complete general and dimensional characteristics for flange heads, split flange clamps (FCS), one-piece flange clamps (FC) and ports applicable to four-screw, split and one-piece flange clamp type tube and hose connectors for use at pressures of 3,5 MPa (35 bar) to 35 MPa (350 bar). It also specifies the dimensions of the seals to be used, as well as the grooves to house the seal. This part of ISO 6162 also recognizes the need to accommodate metric (type 1) screw fasteners, as well as to provide a means to use existing inch (type 2) screw fasteners. These connectors are intended for application in hydraulic systems on industrial and commercial products, where it is desired to avoid the use of threaded connectors. Surges of pressure higher than the nominal ratings will reduce the ability of the flange connectors to retain the hydraulic fluid. This shall be taken into account in the design of the hydraulic system. note: 1) 1 bar = 0,1 MPa = 10 Pa; 1 Pa = 1 N/m.

Hydraulic fluid power - Flange connectors with split or one-piece flange clamps and metric or inch screws - Part 1: Flange connectors for use at pressures of 3,5 MPa (35 bar) to 35 MPa (350 bar), DN 13 to DN 127

ISO 6605:2002 液压传动.软管及软管组件.试验方法

This International Standard specifies uniform test methods for evaluating the performance of hoses and hose assemblies (hoses and attached hose fittings) used in hydraulic fluid power systems. Specific tests and performance criteria for evaluating hoses and hose assemblies used in hydraulic applications are in accordance with the requirements of the respective product (hoses or hose fitting) specifications.

Hydraulic fluid power - Hoses and hose assemblies - Test methods

DIN 20066:2002 流体动力系统.软管组件.尺寸、要求

This standard is intended to be used for ready assembled hose assemblies using hoses according to the European hase standards and hose connectors light and heavy duty series according to those parts of the International hose connectors standard ISO 12151 which are taken over as German Standards. This standard contains information about the most important criteria for selection and reference of hoses and connectors, the primary installation and connection dimensions as well as the requirements for the installation of hose assemblies. Recommendations are given in this standard for storage, life cycle and necessary inspections to ensure the full functionality of those assemblies.

Fluid power systems - Hose assemblies - Dimensions, requirements

BS ISO 16030:2002 气压流体动力.连接.气口和螺柱端头

This International Standard specifies dimensions and performance requirements for ports and stud ends with parallel threads for pneumatic fluid power applications. It specifies reusable, positively retained seals for leak-free connections, for use at pressures from - 0,09 MPa (- 0,9 bar) up to 1,6 MPa (16 bar). Only this International Standard is applicable for threaded ports and stud ends specified in new designs in pneumatic fluid power applications. Ports and stud ends conforming to this International Standard are not intended to connect with ports and stud ends that conform to ISO 1179 or threads that conform to ISO 7-1. note: 1) 1 bar = 0,1 MPa = 10Pa; 1 MPa = 1 N/mm

Pneumatic fluid power - Connections - Ports and stud ends

NP EN ISO 8434-1:2000 用于流体传动和一般用途的金属管接头　第1部分：24度缩式管接头（ISO 8434-1-1994）

Metallic tube connections for fluid power and general use Part 1:24° compression fittings(ISO 8434-4:1994)

ISO 16030:2001 气压传动 连接 气口和双头螺栓端

This International Standard specifies dimensions and performance requirements for ports and stud ends with parallel threads for pneumatic fluid power applications. It specifies reusable, positively retained seals for leak-free connections, for use at pressures from - 0,09 MPa (- 0,9 bar) up to 1,6 MPa (16 bar). Only this International Standard is applicable for threaded ports and stud ends specified in new designs in pneumatic fluid power applications. Ports and stud ends conforming to this International Standard are not intended to connect with ports and stud ends that conform to ISO 1179 or threads that conform to ISO 7-1. note: 1) 1 bar = 0,1 MPa = 10Pa; 1 MPa = 1 N/mm

Pmeumatic fluid power - Connections - Portsand and stud ends

ISO 3862-1:2001 橡胶软管和软管组件 覆盖螺旋金属丝的橡胶增强液压软管 规范 第1部分：油基流体的应用

This part of ISO 3862 specifies requirements for five types of spiral-wire-reinforced hydraulic hoses and hose assemblies of nominal bore from 6,3 to 51. They are suitable for use with hydraulic fluids HH, HL, HM, HR and HV in accordance with ISO 6743-4, at temperatures ranging from -40 ℃ to + 100 ℃ for types 4SP and 4SH and -40 ℃ to + 120 ℃ for types R12, R13 and R15. This part of ISO 3862 does not include requirements for end fittings. It is limited to requirements for the performance of hoses and hose assemblies. NOTE It is the responsibility of the user, in consultation with the hose manufacturer, to establish compatibility of the hose with the fluid to be used.

Rubber hoses and hose assemblies - Rubber-covered spiral-wire-reinforced hydraulic types; Specification - Part 1: Oil-based fluid applications

ISO 4079-1:2001 橡胶软管和软管组件 织物增强液压软管 规范 第1部分：油基流体的应用

This part of ISO 4079 specifies requirements for five types of textile-reinforced hydraulic hoses and hose assemblies of nominal bore from 5 to 100. They are suitable for use with hydraulic fluids HH, HL, HM, HR and HV in accordance with ISO 6743-4 at temperatures ranging from -40 ℃ to +100 ℃. This part of ISO 4079 does not include requirements for end fittings. It is limited to requirements for the performance of hoses and hose assemblies. NOTE It is the responsibility of the user, in consultation with the hose manufacturer, to establish compatibility of the hose with the fluid to be used.

Rubber hoses and hose assemblies - Textile-reinforced hydraulic types; Specification - Part 1: Oil-based fluid applications

DS/EN ISO 9974-3:2001 一般用途和流体动力连接件 带 ISO 261 螺纹的端口和螺柱端，带弹性体或金属对金属密封 第3部分：带金属对金属密封的螺柱端（B 型）

This part of EN ISO 9974 specifies dimensions, performance requirements and test procedures for heavy-duty (S series) and light-duty (L series) and extra-light-duty (LL series) stud ends with ISO 261 threads and metal-to-metal sealing. It also specifies the designation of these stud ends.

Connections for general use and fluid power - Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing - Part 3: Stud ends with metal-to-metal sealing (type B)

DS/EN ISO 9974-1:2001 一般用途和流体动力连接件 带 ISO 261 螺纹的端口和螺柱端，带弹性体或金属对金属密封 第1部分：螺纹端口

This part of EN ISO 9974 specifies dimensions for ports with ISO 261 threads and elastomeric (type E) or metal-to-metal (type B) sealing for general use and in fluid power applications with the stud ends detailed in EN ISO 9974-2 and EN ISO 9974-3.

Connections for general use and fluid power - Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing - Part 1:Treaded ports

DS/EN ISO 9974-2:2001 一般用途和流体动力连接件 带 ISO 261 螺纹的端口和螺柱端，带弹性密封或金属对金属密封 第2部分：带弹性密封的螺柱端（E 型）

This part of EN ISO 9974 specifies dimensions, performance requirements and test procedures for heavy-duty (S-series) and light-duty (L series) stud ends with ISO 261 threads and the elastomeric sealing that is used with them. It also specifies the designation of these stud ends and their elastomeric sealing.

Connections for general use and fluid power - Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing - Part 2: Stud ends with elastomeric sealing (type E)

NF E48-058-2:2001 液压动力.快速装拆的耦合器.第2部分:试验方法

Hydraulic fluid power - Quick-action couplings - Part 2 : test methods.