23.100.40 管道和管接头 标准查询与下载

NF E48-057-2:2001 流体动力和一般用途的连接件.诊断用的液压耦合器.第2部分:在压力下用 M16X2端部进行的耦合连接

Connections for fluid power and general use - Hydraulic couplings for diagnostic purposes - Part 2 : coupling with M16 X 2 end for connection under pressure.

NF E48-058-1:2001 液压流体动力.快速装拆的耦合器.第1部分:尺寸和要求

Hydraulic fluid power - Quick-action couplings - Part 1 : dimensions and requirements.

JIS B 2356-1:2001 一般用途的和流体动力用接头.带弹性密封件或金属与金属间密封件的ISO 261螺纹的端口和螺柱端头.第1部分:螺纹端口

この規格は，JIS B 2356-2及のIS B 2356-3に詳細に規定されている，エラストマシール又はエッジシールによる継手端部を接続するためのメートルねじ((JIS B 0207)ポートの寸法について規定する。また，ポートの試験方法及び呼び方についても規定する。なお，最高使用圧力は，サィズ，材質などによって異なる。

Connections for general use and fluid power -- Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing -- Part 1: Threaded ports

JIS B 2358-1:2001 一般用途的和流体动力用接头.带ISO 261螺纹和O形环密封件的端口和螺柱端头.第1部分:在截断外壳体内装有O形密封件的端口

この規格は， ISO 11926-2及びISO 11926-3で規定された，継手端部を接続するためのユニファイねじポートについて規定する。なお，最高使用圧力は，サィズ，材質などによって異なる。

Connections for general use and fluid power -- Ports and stud ends with ISO 725 threads and O-ring sealing -- Part 1: Ports with O-ring seal in truncated housing

SAE J516-2001 液压软管接头

This SAE Standard provides general and dimensional specifications for the most common hose fittings used in conjunction with hydraulic hoses specified in SAE J517 and utilized in hydraulic systems on mobile and stationary equipment. The general specifications contained in Sections 1 through 15 are applicable to all hydraulic hose fittings and supplement the detailed specifications for the 100R-series fittings contained in the later sections of this document. This document shall be utilized as a procurement document only to the extent agreed upon by the manufacturer and user. Refer to SAE J517 for specifications of hose and information on hose assemblies. SAE J1273 contains information on application factors affecting hose fittings, hose, and hose assemblies.

Hydraulic Hose Fittings

BS ISO 15171-2:2000 流体动力和通用连接器.诊断用液压联轴器.加压连接用M16×2端头

This part of ISO 15171 specifies dimensions, performance requirements and test procedures for a diagnostic cou-pling with an M14 × 1,5 straight stud end to mate with an ISO 6149-1 port and an M16 × 2 connection end that can be connected under pressure without tools to a maximum pressure of 40 MPa [400 bar]. The dimensions of the coupling counterpart are specified. The coupling is designed for use in hydraulic systems that use mineral oil. NOTE The use of this coupling with fluids other than mineral oil requires an agreement between the supplier and the purchaser. Couplings in accordance with this part of ISO 15171 may be used at a maximum working pressure of 63 MPa (630 bar). The permissible working pressure depends upon the materials, design, working conditions, application, etc. Conformance to the dimensional information in this part of ISO 15171 does not guarantee rated performance. Each manufacturer should perform testing according to the specification contained in this part of ISO 15171 to assure that components comply with the performance rating. note:1) 1 bar = 0,1 MPa = 10 Pa; 1 Pa = 1 N/m

Connections for fluid power and general use. Hydraulic couplings for diagnostic purposes. Coupling with M16 x 2 end for connection under pressure

NF E49-300:2000 气压流体动力.用排液容器测定空气借记系数特性的方法

Pneumatic fluid power - Method of characterization of air debit coefficients by drains reservoir.

DIN 2445 Bb.1:2000 承受动态载荷的无缝钢管.设计规则

Seamless steel tubes for dynamic loads - Design rules

DIN 2445-1:2000 承受动态载荷的无缝钢管.第1部分:流体系统用压力为100至500巴的热轧管

The document gives a survey on hot finished straight seamless steel tubes for dynamic loads for use preferably in high pressure fluid systems with an allowable pressure up to 500 bar.

Seamless steel tubes for dynamic loads - Part 1: Hot finished tubes in fluid systems, 100 to 500 bar

DIN 2445-2:2000 承受动态载荷的无缝钢管.第2部分:流体系统用压力为100至500巴的精密钢管

The document gives a survey on sraight seamless cold drawn steel tubes for precision application for dynamic loads to be used preferably in high pressure fluid systems with an pressure up to 500 bar.

Seamless steel tubes for dynamic loads - Part 2: Steel tubes for precision application in fluid systems, 100 bar to 500 bar

ISO 15171-2:2000 用于流体传动和一般用途的管接头 诊断用液压管接头 第2部分:带M16×2螺纹端的压力连接接头

This part of ISO 15171 specifies dimensions, performance requirements and test procedures for a diagnostic cou-pling with an M14 × 1,5 straight stud end to mate with an ISO 6149-1 port and an M16 × 2 connection end that can be connected under pressure without tools to a maximum pressure of 40 MPa [400 bar]. The dimensions of the coupling counterpart are specified. The coupling is designed for use in hydraulic systems that use mineral oil. NOTE The use of this coupling with fluids other than mineral oil requires an agreement between the supplier and the purchaser. Couplings in accordance with this part of ISO 15171 may be used at a maximum working pressure of 63 MPa (630 bar). The permissible working pressure depends upon the materials, design, working conditions, application, etc. Conformance to the dimensional information in this part of ISO 15171 does not guarantee rated performance. Each manufacturer should perform testing according to the specification contained in this part of ISO 15171 to assure that components comply with the performance rating. note: 1) 1 bar =0,1 MPa = 10 Pa; 1 Pa = 1 N/m

Connections for fluid power and general use - Hydraulic couplings for diagnostic purposes - Part 2: Coupling with M16 × 2 end for connection under pressure

JIS B 2351-5:2000 液力和一般用途金属管接头.第5部分.螺纹液压动力接头的试验方法

この規格は，油圧用のねじ付き金属製管継手及びスタッドエンドの試験及び性能評価方法について規定する。

Metallic tube connections for fluid power and general use -- Part 5: Test methods for threaded hydraulic fluid power connections

JIS B 2351-1:2000 液力和一般用途金属管接头.第1部分.24度SIGN压合接头

この規格は，24°くい込み式管継手の設計と性能に関する一般要求事項及び寸法について規定する。適用する管は，外径4～42 mmまでの鉄製及び非鉄製とし，この規格の中で規定した圧力と温度の範囲で，油圧・空気圧用及びー般用に使用する。この継手は，ISO 1179-1， ISO 6149-1及びISO 9974-1に規定した各種ポートに，管やホース継手を接続することを目的としている。

Metallic tube connections for fluid power and general use -- Part 1: 24 degree SIGN compression fittings

BS ISO 7241-2:2000 液压传动.快换接头.试验方法

This part of ISO 7241 specifies different test methods which could be applied to quick-action couplings. NOTE Users of this part ISO 7241 may select only the tests applicable to their needs. It is not intended that all tests be carried out for every application. This part of ISO 7241 is applicable to male and female coupling halves, complete couplings, couplings with and without sealing means when uncoupled, and couplings that are connected and disconnected by a linear and/or rotational motion.

Hydraulic fluid power - Quick-action couplings - Test methods

EN ISO 8434-4:2000 用于流体传动和一般用途的金属管接头.第4部分:带O形圈焊接接头体的24度锥形管接头

Metallic Tube Connections for Fluid Power and General Use - Part 4: 24 Degree Cone Connectors with O-Ring Weld-on Nipples

BS ISO 16028:2000 液压流体动力.在20MPa(200巴)到31.5MPa(315巴)的压力下使用平面型速动联轴器.规范

This International Standard specifies the interface dimensions for interchangeability and specifies the performance requirements for hydraulic, flush-face type, quick-action couplings for use at pressures of 20 MPa (200 bar) to 31,5 MPa (315 bar). Couplings in accordance with this International Standard are not designed to connect or disconnect under pressure. NOTE Couplings in accordance with this International Standard provide for automatic sealing of the fluid pressure on the upstream side and on the downstream side when the coupling is disconnected.

Hydraulic fluid power - Flush-face type, quick-action couplings for use at pressures of 20 MPa (200 bar) to 31,5 MPa (315 bar) - Specifications

ISO 7241-2:2000 液压传动 快换接头 第2部分:试验方法

This part of ISO 7241 specifies different test methods which could be applied to quick-action couplings. NOTE Users of this part ISO 7241 may select only the tests applicable to their needs. It is not intended that all tests be carried out for every application. This part of ISO 7241 is applicable to male and female coupling halves, complete couplings, couplings with and without sealing means when uncoupled, and couplings that are connected and disconnected by a linear and/or rotational motion.

Hydraulic fluid power - Quick-action couplings - Part 2: Test methods

ISO 16028:1999 液压传动 用于压力为20 MPa(200 bar)～31.5 MPa(315 bar)的平面对接型快速接头 规范

This International Standard specifies the interface dimensions for interchangeability and specifies the performance requirements for hydraulic, flush-face type, quick-action couplings for use at pressures of 20 MPa (200 bar) to 31,5 MPa (315 bar). Couplings in accordance with this International Standard are not designed to connect or disconnect under pressure. NOTE Couplings in accordance with this International Standard provide for automatic sealing of the fluid pressure on the upstream side and on the downstream side when the coupling is disconnected.

Hydraulic fluid power - Flush-face type, quick-action couplings for use at pressures of 20 MPa (200 bar) to 31,5 MPa (315 bar) - Specifications

BS ISO 15171-1:1999 液压和一般用途的连接.诊断用的液压联结器.不用于压力条件下连接的联结器

This part of ISO 15171 specifies dimensions, performance requirements and test procedures for the male quick-action half of a metric coupling with an M14 × 1,5 straight stud end to mate with an ISO 6149-1 port, to be used for diagnostic purposes. Couplings in accordance with this part of ISO 15171 are not designed to connect under pressure. The coupling is designed for use in hydraulic systems that use mineral oil. NOTE Use of this coupling with fluids other than mineral oil requires agreement between the supplier and the purchaser. This part of ISO 15171 does not apply to the female half of the mating hydraulic quick-action coupling, which is not on the machine. Couplings in accordance with this part of ISO 15171 may be used at a maximum working pressure of 40MPa [400 bar]. The permissible working pressure depends upon the materials, design, working conditions, application, etc. Conformance to the dimensional information in this part of ISO 15171 does not guarantee rated performance. Each manufacturer should perform testing in accordance with the specification contained in this part of ISO 15171 to assure that components comply with the performance rating. note:1 bar = 0,1 MPa = 10 Pa; 1 Pa = 1 N/m

Connections for fluid power and general use - Hydraulic couplings for diagnostic purposes - Coupling not for connection under pressure

NF E48-088:1999 橡胶和塑料软管组件.液压脉冲弯曲试验(半Ω 型试验)

Rubber and plastics hose assemblies. Flexing combined with hydraulic impulse test (half-omega test).