23.100.40 管道和管接头 标准查询与下载

ISO 15171-1:1999 用于流体传动和一般用途的管接头 诊断用液压管接头 第1部分:非压力下连接的管接头

This part of ISO 15171 specifies dimensions, performance requirements and test procedures for the male quick-action half of a metric coupling with an M14 × 1,5 straight stud end to mate with an ISO 6149-1 port, to be used for diagnostic purposes. Couplings in accordance with this part of ISO 15171 are not designed to connect under pressure. The coupling is designed for use in hydraulic systems that use mineral oil. NOTE Use of this coupling with fluids other than mineral oil requires agreement between the supplier and the purchaser. This part of ISO 15171 does not apply to the female half of the mating hydraulic quick-action coupling, which is not on the machine. Couplings in accordance with this part of ISO 15171 may be used at a maximum working pressure of 40MPa [400 bar]. The permissible working pressure depends upon the materials, design, working conditions, application, etc. Conformance to the dimensional information in this part of ISO 15171 does not guarantee rated performance. Each manufacturer should perform testing in accordance with the specification contained in this part of ISO 15171 to assure that components comply with the performance rating. note: 1) 1 bar = 0,1 MPa = 10 Pa; 1 Pa = 1 N/m

Connections for fluid power and general use - Hydraulic couplings for diagnostic purposes - Part 1: Coupling not for connection under pressure

ISO 12151-1:1999 液压传动和通用联接件 软管接头 第1部分:带ISO 8434-3 O形圈端面密封末端的软管接头

This part of ISO 12151 specifies the general and dimensional requirements for the design and performance of hose fittings with O-ring face seal ends in accordance with ISO 8434-3, made of carbon steel, for nominal hose inside diameters of 6,3 mm to 38 mm inclusive, in accordance with ISO 4397. NOTE 1 Materials other than carbon steel may be supplied as agreed between the manufacturer and user. NOTE 2 For hose fittings used in hydraulic braking systems on road vehicles (as defined in the scope of ISO/TC 22), see ISO 4038. These hose fittings (see Figure 1 for a typical example) are for use in hydraulic fluid power systems with hose that meets the requirements of the respective hose standards and in general applications with suitable hose.

Connections for hydraulic fluid power and general use - Hose fittings - Part 1: Hose fittings with ISO 8434-3 O-ring face seal ends

ISO 12151-3:1999 液压传动和通用联接件 软管接头 第3部分:带ISO6162法兰末端的软管接头

This part of ISO 12151 specifies the general and dimensional requirements for the design and performance of flange hose fittings, made of carbon steel, for nominal hose inside diameters of 12,5 mm to 51 mm inclusive, in accordance with ISO 4397, for use with ports and clamps in accordance with ISO 6162. NOTE 1 Materials other than carbon steel may be supplied as agreed between the manufacturer and user. NOTE 2 For hose fittings used in hydraulic and pneumatic braking systems on road vehicles (as defined in the scope of ISO/TC 22/SC 2), see ISO 4038, ISO 4039-1 and ISO 4039-2. These hose fittings (see Figure 1 for a typical example) are for use in hydraulic fluid power systems with hose that meets the requirements of the respective hose standards and in general applications with suitable hoses.

Connections for hydraulic fluid power and general use - Hose fittings - Part 3: Hose fittings with ISO 6162 flange ends

EN ISO 8032:1999 橡胶和塑料软管组件.带液压脉冲试验的组合式弯曲(半Ω 型试验)

Rubber and Plastics Hose Assemblies - Flexing Combined with Hydraulic Impulse Test (Half-Omega Test)

NF T47-286:1998 橡胶或塑料软管和软管组件.无屈挠液压脉冲试验

Rubber or plastics hoses and hose assemblies. Hydraulic-pressure impulse test without flexing.

NF E48-550:1998 流体动力系统.O型环外罩.轴或镗孔中静态组件的外罩的设计

Fluid power systems. O-ring housings. Design of housing for static assemblies in shaft or bore.

BS EN ISO 8032:1999 橡胶和塑料软管组件.液压脉冲弯曲试验(半Ω型试验)

This International Standard specifies a method of flexing, in an arrangement known as a "half-omega", hydraulic hose assemblies during impulse testing.

Rubber and plastics hose assemblies. Flexing combined with hydraulic impulse test (half-omega test)

BS EN ISO 8032:1998 橡胶和塑料软管组件 液压脉冲弯曲试验（半Ω型试验）

Rubber and plastics hose assemblies. Flexing combined with hydraulic impulse test (half-omega test)

NF E48-064:1998 流体动力和一般用途的金属管连接件.第1部分:24 度喇叭形压合接头

Metallic tube connections for fluid power and general use. Part 1 : 24 degrees compression fittings.

DIN EN ISO 8434-1:1997 液压传动和通用连接件.第1部分:24度喇叭形压合接头

The document specifies general and dimensional requirements for the design and performance of 24?compression fittings which are suitable for the use with tubes with outside diameters from 4 mm to 42 mm.

Metallic tube connections for fluid power and general use - Part 1: 24° compression fittings (ISO 8434-1:1994); German version EN ISO 8434-1:1997

ISO 8032:1997 橡胶和塑料软管组件 液压脉冲弯曲试验(半Ω 型试验)

This International Standard specifies a method of flexing, in an arrangement known as a 'half-omega", hydraulic hose assemblies during impulse testing.

Rubber and plastics hose assemblies - Flexing combined with hydraulic impulse test (half-omega test)

DIN EN ISO 6803:1997 橡胶和塑料软管及软管组件.无弯曲液压压力脉冲试验

The document describes a pressure impulse test without flexing for rubber or plastics hyraulic hoses and hose assemblies.

Rubber or plastics hoses and hose assemblies - Hydraulic-pressure impulse test without flexing (ISO 6803:1994); German version EN ISO 6803:1997

BS EN 856:1997 橡胶软管和软管组件.橡胶包覆螺旋形金属丝增强的液压用类型.规范

This European Standard specifies requirements for four types of rubber covered spiral wire reinforced hydraulic hoses and hose assemblies of nominal bore from 6 to 51. They are suitable for use with : - hydraulic fluids in accordance with ISO 6743-4 with the exception of HFD R, HFD S and HFD T at temperatures ranging from -40 ℃ to +100 ℃ for types 4SP and 4SH and -40 ℃ to +120 ℃ for types R12 and R13; - water based fluids at temperatures ranging from -40 ℃ to +70 ℃. - water fluids at temperatures ranging from 0 ℃ to +70 ℃. The standard does not include requirements for end fittings. It is limited to the performance of hoses and hose assemblies. NOTE 1. The hoses are not suitable for use with castor oil based nor ester based fluids. NOTE 2. Hoses and hose assemblies should not be operated outside the limits of this standard. NOTE 3. Requirements for hydraulic hoses for underground mining are standardized in separate standards.

Rubber hoses and hose assemblies - Rubber-covered spiral wire reinforced hydraulic type - Specification

BS EN 857:1997 软管及软管部件.液压用的金属线编带增强的抗挤压类型.规范

This European Standard specifies requirements for two types of wire braid reinforced compact hoses and hose assemblies of nominal bore from 6 to 25. They are suitable for use with: - hydraulic fluids in accordance with ISO 6743-4 with the exception of HFD R, HFD S and HFD T at temperatures ranging from -40 ℃ to +100 ℃; - water based fluids at temperatures ranging from-40 ℃ to+70 ℃; - water at temperatures ranging from 0 ℃ to +70 ℃. The standard does not include requirements for end fittings. It is limited to the performance of hoses and hose assemblies. NOTE 1. The hoses are not suitable for use with castor oil based nor ester based fluids. NOTE 2. Hoses and hose assemblies should not be operated outside the limits of this standard. NOTE 3. Requirements for hydraulic hoses for underground mining are standardized in separate standards.

Rubber hoses and hose assemblies - Wire braid reinforced compact type for hydraulic applications - Specification

NF E48-560:1997 液压驱动系统. O形垫圈.轴向装配设计

FLUID POWER SYSTEMS. O-RING HOUSINGS. AXIAL ASSEMBLY DESIGNS.

BS 5200:1997 水管接头和转接器的尺寸规范

Basic dimensions to ensure interchangeability of connectors and adaptors for connecting rigid or flexible tubing to hydraulic system components.

Specification for dimensions of hydraulic connectors and adaptors

NF T47-270:1997 橡胶软管和软管组件.橡胶包皮螺旋金属线增强式液压型.规范

Rubber hoses and hose assemblies. Rubber-covered spiral wire reinforced hydraulic type. Specification.

EN ISO 6803:1997 橡胶或塑料软管和软管组件.非柔性液压脉冲试验 ISO 6803-1994

Rubber or Plastics Hoses and Hose Assemblies - Hydraulic-Pressure Impulse Test without Flexing ISO 6803: 1994

NF T47-288:1997 橡胶软管和软管组件.液压设备用金属丝编织物增强式紧凑型.规范

Rubber hoses and hose assemblies. Wire braid reinforced compact type for hydraulic applications. Specification.

DIN EN 856:1997 橡胶软管和软管组件.带金属丝螺旋垫层的液压软管.规范

The document specifies requirements for four types of wire braid reinforced hoses and hose assemblies of nominal bore from 6 to 51.

Rubber hoses and hose assemblies - Rubber-covered spiral wire reinforced hydraulic type - Specification; German version EN 856:1996