23.100.40 管道和管接头 标准查询与下载
共找到 485 条与 管道和管接头 相关的标准，共 33 页
This document specifies the general and dimensional requirements for the design and performance of hose fittings with 24° cone connector ends with O -rings according to ISO 8434-1 . These hose fittings are made ofcarbon steel and are intended for use with hoses with nominal inside diameters from 5 mm through 38 mm (inclusive). NO TE For hose fittings used in hydraulic and pneumatic braking s ys tems on road vehicles, see ISO 4038 , These hose fittings are for use in hydraulic fluid power s ystems with hoses that meet the requirements of respective hose standards and in general applications with suitable hoses.
Connections for hydraulic fluid power and general use — Hose fittings — Part 2: Hose fittings with ISO 8434-1 24° cone connector ends with O-rings
- ICS
- 23.100.40
- CCS
- 发布
- 2022-10-14
- 实施
1 Scope This document specifies dimensions and performance requirements for ports and stud ends with parallel threads (G series thread) for pneumatic fluid power applications. It specifies reusable, positively retained seals for leak-free connections, for use at pressures from −0,09 MPa (−0,9 bar 1 ) up to 1,6 MPa (16 bar). This document is applicable for threaded ports and stud ends specified in new designs in pneumatic fluid power applications. WARNING Ports and stud ends conforming to this document are not intended to connect with ports and stud ends that conform to ISO 1179 (all parts) or threads that conform to ISO 7-1. As shown in Figure 1, significant differences in thread depth exists between ISO 16030 requirement and ISO 1179-1 (Δ1 and Δ2) that makes ports and stud ends conforming to ISO 7-1 unsuitable. Figure 1 — Different thread depths requirements between ISO 16030 and ISO 1179-1
Pneumatic fluid power. Connections. Ports and stud ends
- ICS
- 23.100.40
- CCS
- 发布
- 2022-09-30
- 实施
- 2022-09-30
1 Scope This document specifies dimensions for metric ports for use with the adjustable and non-adjustable stud ends as described in ISO 6149‑2 and ISO 6149‑3. Ports in accordance with this document can be used at working pressures up to 63 MPa (630 bar 1 ) for non-adjustable stud ends and 40 MPa (400 bar) for adjustable stud ends. The permissible working pressure depends upon port size, materials, design, working conditions, application, etc. See ISO 6149‑2 and ISO 6149‑3 for pressure ratings. NOTE The Introduction of this document gives recommendations for ports and stud ends to be used for new designs in hydraulic fluid power applications.
Connections for hydraulic fluid power and general use. Ports and stud ends with ISO 261 metric threads and O-ring sealing - Ports with truncated housing for O-ring seal
- ICS
- 23.100.40
- CCS
- 发布
- 2022-07-31
- 实施
- 2022-07-31
This document specifies dimensions and performance requirements for ports and stud ends with parallel threads (G series thread) for pneumatic fluid power applications. It specifies reusable, positively retained seals for leak-free connections, for use at pressures from −0,09 MPa (−0,9 bar 1)) up to 1,6 MPa (16 bar). This document is applicable for threaded ports and stud ends specified in new designs in pneumatic fluid power applications. WARNING — Ports and stud ends conforming to this document are not intended to connect with ports and stud ends that conform to ISO 1179 (all parts) or threads that conform to ISO 7-1. As shown in Figure 1, significant differences in thread depth exists between ISO 16030 requirement Figure 1 — Different thread depths requirements between ISO 16030 and ISO 1179-1
Pneumatic fluid power — Connections — Ports and stud ends
- ICS
- 23.100.40
- CCS
- 发布
- 2022-07-15
- 实施
This document specifies dimensions for metric ports for use with the adjustable and non-adjustable stud ends as described in ISO 6149‑2 and ISO 6149‑3. Ports in accordance with this document can be used at working pressures up to 63 MPa (630 bar[1]) for non-adjustable stud ends and 40 MPa (400 bar) for adjustable stud ends. The permissible working pressure depends upon port size, materials, design, working conditions, application, etc. See ISO 6149‑2 and ISO 6149‑3 for pressure ratings. NOTE The Introduction of this document gives recommendations for ports and stud ends to be used for new designs in hydraulic fluid power applications. [1] 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2.
Connections for hydraulic fluid power and general use - Ports and stud ends with ISO 261 metric threads and O-ring sealing - Part 1: Ports with truncated housing for O-ring seal (ISO 6149-1:2022)
- ICS
- 23.100.40
- CCS
- 发布
- 2022-06-29
- 实施
- 2022-09-30
This document specifies dimensions for metric ports for use with the adjustable and non-adjustable stud ends as described in ISO 6149-2 and ISO 6149-3. Ports in accordance with this document can be used at working pressures up to 63 MPa (630 bar1)) for non-adjustable stud ends and 40 MPa (400 bar) for adjustable stud ends. The permissible working pressure depends upon port size, materials, design, working conditions, application, etc. See ISO 6149-2 NOTE The Introduction of this document gives recommendations for ports and stud ends to be used for new designs in hydraulic fluid power applications.
Connections for hydraulic fluid power and general use — Ports and stud ends with ISO 261 metric threads and O-ring sealing — Part 1: Ports with truncated housing for O-ring seal
- ICS
- 23.100.40
- CCS
- 发布
- 2022-06-13
- 实施
Connectors for pneumatic fluid power -- Part 1: Push-in connectors for thermoplastic tubes
- ICS
- 23.100.40
- CCS
- 发布
- 2022-02-21
- 实施
本文件规定了民用飞机液压导管及连接件旋转弯曲疲劳试验方法。 本文件适用于各类可拆卸式和不可拆卸式的液压导管及连接件旋转弯曲疲劳试验。
Rotary flexure test method of hydraulic tubing joints and fittings for civil aircraft
- ICS
- 23.100.40
- CCS
- C374
- 发布
- 2022-01-25
- 实施
- 2022-01-28
Connections for hydraulic fluid power and general use — Hose fittings — Part 3: Hose fittings with ISO 6162-1 or ISO 6162-2 flange ends
- ICS
- 23.100.40
- CCS
- 发布
- 2021-10-29
- 实施
Rubber hoses and hose assemblies - Rubber-covered spiral wire reinforced hydraulic type - Specification
- ICS
- 23.100.40
- CCS
- 发布
- 2021-10-00
- 实施
- 2021-10-01
This standard applies to hydraulic hose assemblies consisting of rubber and plastic hoses of several types and hose fittings in accordance with DIN ISO 12151-2 and DIN ISO 12151-3. It defines the most important features for the selection and assignment of hoses and fittings, inst
Hydraulic fluid power - Hose assemblies - Dimensions, requirements
- ICS
- 23.100.40
- CCS
- 发布
- 2021-07-00
- 实施
Metallic tube connections for fluid power and general use - Test methods for hydraulic fluid power connections (ISO 19879:2021)
- ICS
- 23.100.40
- CCS
- 发布
- 2021-06-15
- 实施
- 2021-06-15
Connections for general use and fluid power -- Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing -- Part 2: Stud ends with elastomeric sealing (type E)
- ICS
- 23.100.40
- CCS
- J15
- 发布
- 2021-05-20
- 实施
Plastics hoses and hose assemblies - Textile-reinforced types for hydraulic applications - Specification (ISO 3949:2020, Corrected version 2020-12)
- ICS
- 23.100.40
- CCS
- 发布
- 2021-05-15
- 实施
- 2021-05-15
Metallic tube connections for fluid power and general use - Test methods for hydraulic fluid power connections
- ICS
- 23.100.40
- CCS
- 发布
- 2021-03-31
- 实施
- 2021-07-02
Hydraulic fluid power systems -- Assembled systems -- Methods of cleaning lines by flushing
- ICS
- 23.100.40
- CCS
- 发布
- 2021-03-11
- 实施
- 2021-03-11
Plastics hoses and hose assemblies -- Textile-reinforced types for hydraulic applications -- Specification (ISO 3949:2020)
- ICS
- 23.100.40
- CCS
- 发布
- 2021-02-05
- 实施
- 2021-02-05
Plastics hoses and hose assemblies - Textile-reinforced types for hydraulic applications - Specification (ISO 3949:2020)
- ICS
- 23.100.40
- CCS
- 发布
- 2021-01-00
- 实施
- 2021-01-01
Pneumatic fluid power. Push-in connectors for thermoplastic tubes
- ICS
- 23.100.40
- CCS
- 发布
- 2020-11-12
- 实施
- 2020-11-12
This document specifies requirements for three types of textile-reinforced thermoplastics hoses and hose assemblies of nominal size from 3,2 to 25. Each type is divided into two classes dependent on electrical conductivity requirements. They are suitable for use with: — oil-based hydraulic fluids HH, HL, HM, HR and HV as defined in ISO 6743‑4 at temperatures ranging from −40 °C to +93 °C; — water-based fluids HFC, HFAE, HFAS and HFB as defined in ISO 6743‑4 at temperatures ranging from 0 °C to +60 °C — water at temperatures ranging from 0 °C to +60 °C. This document does not include any requirements for end fittings. It is limited to the performance of hoses and hose assemblies. NOTE It is the responsibility of the user, in consultation with the hose manufacturer, to establish the compatibility of the hose with the fluid to be used.
Plastics hoses and hose assemblies - Textile-reinforced types for hydraulic applications - Specification (ISO 3949:2020, Corrected version 2020-12)
- ICS
- 23.100.40
- CCS
- 发布
- 2020-08-12
- 实施
- 2020-11-30
