23.100.40 管道和管接头 标准查询与下载

ISO 10763:2020 液压流体动力 - 平头 无缝和焊接精密钢管 - 尺寸和标称工作压力

This document specifies sizes and nominal working pressures for seamless and welded precision steel tubes with outside diameters in accordance with ISO 4397, and wall thicknesses and mechanical properties in accordance with ISO 3305. The nominal working pressures included in this document reflect a design factor ratio of 4 to 1 applied to the calculated burst pressures.

Hydraulic fluid power — Plain-end, seamless and welded precision steel tubes — Dimensions and nominal working pressures

BS ISO 23309:2020 液压流体动力系统 组装系统 冲洗管道的方法

What is ISO 23309 about?    ISO 23309 discusses hydraulic fluid power systems. A hydraulic fluid power system has a pump driven by a prime mover (such as an electric motor or internal combustion engine) that converts mechanical energy into fluid energy. ISO 23309 specifies the procedures for flushing particulate contamination from the hydraulic lines and components of hydraulic fluid power systems which is:   Residual in the components after manufacture   Introduced into the system during the assembly of a new system

Hydraulic fluid power systems. Assembled systems. Methods of cleaning lines by flushing

ISO 23309:2020 液压动力系统 - 组装系统 - 通过冲洗清洗管道的方法

This document specifies the procedures for flushing particulate contamination from the hydraulic lines and components of hydraulic fluid power systems which is: — residual in the components after manufacture; — introduced into the system during the assembly of a new system; or — introduced into the system after system failure, maintenance or modification of an existing system. The aim of flushing the system is to quickly remove this contamination to reduce the amount of wear and damage that results if these particles are allowed to circulate around the system. This document is not applicable to: — the chemical cleaning and pickling of hydraulic tubes; — the cleaning of major system components (this is covered in ISO/TR 10949).

Hydraulic fluid power systems — Assembled systems — Methods of cleaning lines by flushing

ASTM A822/A822M-20 无缝冷拔碳钢管液压系统服务标准规范

1.1 This specification covers nominal wall thickness, seamless, cold-drawn carbon steel tubing intended for use in hydraulic systems and in other similar applications where forming operations require tight radius bending and flaring. 1.2 Tubing sizes and thicknesses usually furnished to this specification are 1⁄8 to 31⁄2 in. [3.2 to 88.9 mm] in outside diameter and 0.035 to 0.134 in. [0.9 to 3.4 mm] inclusive, in nominal wall thickness. Tubing having other dimensions may be furnished, provided such tubing complies with all other requirements of this specification. 1.3 Mechanical property requirements do not apply to tubing smaller than 1⁄8 in. [3.2 mm] in inside diameter or 0.015 in. [0.4 mm] in thickness. 1.4 Optional supplementary requirements are provided and, when desired, shall be so stated in the order. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Seamless Cold-Drawn Carbon Steel Tubing for Hydraulic System Service

ISO 14743:2020 气动流体动力 - 用于热塑性管的推入式连接器

This document specifies the general requirements and test methods for the design and performance of push-in connectors for use with thermoplastic tubes with outside diameters (OD) from 3 mm to 16 mm including dimensions in inches. This document is intended to establish uniform methods of testing complete push-in connector assemblies as used in pneumatic fluid power applications. It is not applicable to air braking systems.

Pneumatic fluid power — Push-in connectors for thermoplastic tubes

DIN EN 856:2020 橡胶软管和软管组件.带金属丝螺旋垫层的液压软管.规范.德文版本EN 856-2015

Ruber hoses and hose assemblies - Rubber-covered spiral wire reinforced hydraulic type - Specification; German version EN 856:2015

KS B ISO 23309-2019 液压流体动力系统 组装系统 冲洗管道的方法

Hydraulic fluid power systems — Assembled systems — Methods of cleaning lines by flushing

KS B ISO 6150-2019 气动流体动力 最大工作压力1MPa、1.6MPa和2.5MPa的圆柱形快速接头 插塞连接尺寸、规格、应用指南和试验

Pneumatic fluid power－Cylindrical quick-action couplings for maximum working pressures of 1 MPa, 1.6 MPa and 2.5 MPa－Plug connecting dimensions, specifications, application guidelines and testing

KS B ISO 6162-1-2019 液压流体动力 带有分体式或一体式法兰夹和公制或英制螺钉的法兰连接器 第1部分：压力为3.5MPa至35MPa、DN13至DN127时使用的法兰连接器

Hydraulic fluid power－Flange connectors with split or one-piece flange clamps and metric or inch screws－Part 1：Flange connectors for use at pressures of 3.5 MPa to 35 MPa, DN13 to DN127

KS B ISO 6162-2-2019 液压流体动力 带有分体式或一体式法兰夹和公制或英制螺钉的法兰连接器 第2部分：压力为35MPa至40MPa、DN13至DN51使用的法兰连接器

Hydraulic fluid power－Flange connectors with split or one-piece flange clamps and metric or inch screws－Part 2：Flange connectors for use at pressures of 35MPa to 40MPa, DN13 to DN51

ISO 10763:2019 液压流体动力 - 平头 无缝和焊接精密钢管 - 尺寸和标称工作压力

Hydraulic fluid power — Plain-end, seamless and welded precision steel tubes — Dimensions and nominal working pressures

T/ZZB 1361-2019 插入式气动管接头

本标准规定了外径为3 mm～12 mm的塑料管所用的插入式气动管接头(以下简称管接头)的术语和定义、结构型式与尺寸规格、分类、代号与标记、基本要求、技术要求、试验方法、检验规则、标识、包 装、运输、贮存和质量承诺。 本标准适用于工作环境温度-20 ℃～+80 ℃、工作压力-0.09 MPa～1.6MPa的气动系统中使用的管接头（埋入式管接头除外）。 本标准不适用于气制动系统。

Pneumatic push-in connectors for tubes

BS ISO 4399:2019 流体动力系统和组件 连接器和相关组件 公称压力

What is ISO 4399 - Fluid power systems and components about? ISO 4399 discusses fluid power systems and components. Fluid power systems perform work by a pressurized fluid bearing directly on a piston in a cylinder or in a fluid motor. ISO 4399 specifies a selection of nominal pressures for hydraulic and pneumatic fluid power connectors and associated components. There can be a need to provide a selection of nominal pressures for connectors and associated components used in applications where the external pressure on the components is greater than the internal pressure, for example, vacuum service. Who is ISO 4399 - Fluid power systems and components for ? ISO 4399 on fluid power systems and components is useful for: Fluid power component manufacturers Fluid power equipment manufacturers Heavy earthmoving machine manufacturers Design engineers Quality control personnel Why should you use ISO 4399 - Fluid power systems and components ? Within a fluid power system, cylinders, and motors (also called actuators) do the desired work. Control components such as valves regulate the system. In hydraulic fluid power systems, power is transmitted and controlled through a liquid under pressure within an enclosed circuit. Components may be connected through their ports by connections (fittings) and conduits. Tubes are rigid conduits. ISO 4399 defines the nominal pressure value that is assigned to a component, piping...

Fluid power systems and components. Connectors and associated components. Nominal pressures

ISO 4399:2019 流体动力系统和组件 - 连接器和相关组件 - 公称压力

This document specifies a selection of nominal pressures for hydraulic and pneumatic fluid power connectors and associated components. NOTE There can be a need to provide a selection of nominal pressures for connectors and associated components used in applications where the external pressure on the components is greater than the internal pressure, for example vacuum service. A document that deals with this subject will be established in due course.

Fluid power systems and components — Connectors and associated components — Nominal pressures

ISO 6149-1:2019 液压油和一般用途的连接 - 带Iso 261公制螺纹和O形密封圈的端口和螺柱端 - 第1部分:带O形圈密封件的截短外壳端口

Connections for hydraulic fluid power and general use — Ports and stud ends with ISO 261 metric threads and O-ring sealing — Part 1: Ports with truncated housing for O-ring seal

ASTM F3226/F3226M-19 管道和管道系统用金属压接配件的标准规范

1.1 This specification establishes the performance characteristics required for Metallic Press-Connect Fittings for use in piping and tubing systems with a maximum allowable working pressure of three-hundred pounds per square inch (300 psi) [2.07 MPa]. These fittings directly attach to pipe or tube by mechanical deformation of the pipe or tube or fitting, or a combination thereof, creating a seal and a restrained joint. The seal may be created via the mechanical deformation (of the pipe, tube or fitting) or created independently. Successful completion of the tests described herein constitutes completion of the technical portion of the qualification process. 1.2 The tests specified are applicable only to ascertain the performance characteristics. These tests are not intended for use in the evaluation of non-Press-Connect Fittings. 1.3 Refer to IACS UR P2.7.4, Table-7 for Metallic Press-Connect Fittings applications. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Metallic Press-Connect Fittings for Piping and Tubing Systems

BS ISO 6150:2018 气动流体动力 圆柱形快速接头 最大工作压力为 1 MPa、1.6 MPa 和 2.5 MPa（10 bar、16 bar 和 25 bar） 插头连接尺寸、规格、应用指南和测试

What is ISO 6150 - Pneumatic fluid power about?    ISO 6150 discusses pneumatic fluid power. A pneumatic power system carries power by employing compressed gas, generally air, as a fluid for transmitting energy from an energy-generating source to an energy-using point to accomplish useful work. ISO 6150 specifies the dimensions and tolerances to ensure the interchangeability of pneumatic quick-action coupling plugs. ISO 6150 also provides specifications and application guidelines and specifies the tests to be applied to the plugs together with sockets.   ISO 6150 applies to cylindrical quick-action couplings for maximum working pressures of 1 MPa, 1,6 MPa and 2,5 MPa (10 bar, 16 bar and 25 bar) for use in pneumatic fluid power systems. ISO 6150 applies only to the dimensional criteria of products manufactured in accordance with ISO 6150 .   Who is ISO 6150 -

Pneumatic fluid power. Cylindrical quick-action couplings for maximum working pressures of 1 MPa, 1,6 MPa, and 2,5 MPa (10 bar, 16 bar and 25 bar). Plug connecting dimensions, specifications, application guidelines and testing

ISO 6150:2018 气动流体动力——最大工作压力为10巴、16巴和25巴（1兆帕、1,6兆帕和2,5兆帕）的圆柱形快接管接头——插头连接尺寸、规格、应用指南和测试

This document specifies the dimensions and tolerances so as to ensure the interchangeability of pneumatic quick-action coupling plugs. It also provides specifications and application guidelines, and specifies the tests to be applied to the plugs together with sockets. NOTE 1 The construction and dimensions of sockets are left to the manufacturer's option. This document applies to cylindrical quick-action couplings for maximum working pressures of 1 MPa, 1,6 MPa and 2,5 MPa (10 bar, 16 bar and 25 bar) for use in pneumatic fluid power systems. NOTE 2 Quick-action couplings with shut-off valves for equipment for welding, cutting and related processes are covered by ISO 7289. This document applies only to the dimensional criteria of products manufactured in accordance with this document. It does not apply to their functional characteristics.

Pneumatic fluid power — Cylindrical quick-action couplings for maximum working pressures of 10 bar, 16 bar and 25 bar (1 MPa, 1,6 Mpa, and 2,5 MPa) — Plug connecting dimensions, specifications, applic

DIN EN ISO 8434-1:2018 流体动力和一般用途的金属管连接 第1部分：24° 锥形连接器（ISO 8434-1:2018）；德文版 EN ISO 8434-1:2018

The document specifies general and dimensional requirements for the design and performance of 24° compression fittings which are suitable for the use with tubes with outside diameters from 4 mm to 42 mm.

Metallic tube connections for fluid power and general use - Part 1: 24° cone connectors (ISO 8434-1:2018); German version EN ISO 8434-1:2018

BS EN ISO 8434-1:2018 液压传动和通用金属管连接. 24度角连接器

Metallic tube connections for fluid power and general use. 24 cone connectors