23.100.40 管道和管接头 标准查询与下载
共找到 485 条与 管道和管接头 相关的标准，共 33 页
Metallic tube connections for fluid power and general use - Part 1: 24��one connectors
- ICS
- 23.100.40
- CCS
- 发布
- 2018-08-01
- 实施
This document specifies the general and dimensional requirements for 24° cone connectors using cutting ring and O-ring seal cone (referred to as DKO) suitable for use with ferrous and non-ferrous tubes with outside diameters from 4 mm to 42 mm inclusive. These connectors are for use in fluid power and general applications within the limits of pressure and temperature specified in this document. They are intended for the connection of plain end tubes and hose fittings to ports in accordance with These connectors provide full-flow connections in hydraulic systems operating to the working pressures shown in Table 1. Because many factors influence the pressure at which a system performs satisfactorily, these values are not intended to be understood as guaranteed minimums. For every application, sufficient testing is meant to be conducted and reviewed by both the user and manufacturer to ensure that required performance levels are met. NOTE 1 For new designs in hydraulic fluid power applications, see the requirements given in 9.6. Where the requirements of the application allow for the use of elastomeric seals, connector designs that conform to International Standards and incorporate elastomeric sealing are preferred. NOTE 2 For use under conditions outside the pressure and/or temperature limits specified, see 5.4. This document also specifies a performance and qualification test for these connectors.
Metallic tube connections for fluid power and general use - Part 1: 24° cone connectors
- ICS
- 23.100.40
- CCS
- J15
- 发布
- 2018-07-01
- 实施
1 Scope This document gives general and dimensional specifications for flanged heads, flange clamps, ports and mounting surfaces applicable to four-screw, one-piece square flange clamp type tube connectors and hose fittings for use at a pressure of 42 MPa [420 bar 1 ]. It also specifies the dimensions of the seals to be used, as well as the grooves that house the seals. These connections are intended for application in hydraulic systems on industrial and commercial products where it is desired to avoid the use of threaded connectors.
Hydraulic fluid power. Four-screw, one-piece square flange connections for use at pressures of 42 MPa, DN 25 to 80
- ICS
- 23.100.40
- CCS
- 发布
- 2018-06-30
- 实施
- 2018-06-30
This document gives general and dimensional specifications for flanged heads, flange clamps, ports and mounting surfaces applicable to four-screw, one-piece square flange clamp type tube connectors and hose fittings for use at a pressure of 42 MPa [420 bar1)]. It also specifies the dimensions of the seals to be used, as well as the grooves that house the seals. These connections are intended for application in hydraulic systems on industrial and commercial products where it is desired to avoid the use of threaded connectors.
Hydraulic fluid power - Four-screw, one-piece square flange connections for use at pressures of 42 MPa, DN 25 to 80
- ICS
- 23.100.40
- CCS
- J20
- 发布
- 2018-06-01
- 实施
Hydraulic fluid power - Hose and hose assemblies - Method of collecting a fluid sample for analyzing the cleanliness of a hose or hose assembly
- ICS
- 23.100.40
- CCS
- 发布
- 2018-04-17
- 实施
1 Scope This document gives general and dimensional specifications for flanged heads, split flange clamps (FCS and FCSM), one-piece flange clamps (FC and FCM), ports and mounting surfaces applicable to four-screw, split and one-piece flange clamp type tube connectors and hose fittings for use at a pressure of 42 MPa (420 bar 1 ). It also specifies the dimensions of the seals to be used, as well as the grooves that house the seals. This document also recognizes the need to accommodate metric screw fasteners (type 1) (for DN 13 to DN 76), as well as to provide a means to use existing inch screw fasteners (type 2) (for DN 13 to DN 51). These connections are intended for application in hydraulic systems on industrial and commercial products where it is desired to avoid the use of threaded connectors.
Hydraulic fluid power. Flange connections with split or one-piece flange clamps and metric or inch screws. Flange connectors, ports and mounting surfaces for use at a pressure of 42 MPa (420 bar), DN 13 to DN 76
- ICS
- 23.100.40
- CCS
- 发布
- 2018-03-31
- 实施
- 2018-03-31
This document gives general and dimensional specifications for flanged heads, split flange clamps (FCS and FCSM), one-piece flange clamps (FC and FCM), ports and mounting surfaces applicable to fourscrew, split and one-piece flange clamp type tube connectors and hose fittings for use at a pressure of 42 MPa (420 bar1)). It also specifies the dimensions of the seals to be used, as well as the grooves that house the seals. This document also recognizes the need to accommodate metric screw fasteners (type 1) (for DN 13 to DN 76), as well as to provide a means to use existing inch screw fasteners (type 2) (for DN 13 to DN 51). These connections are intended for application in hydraulic systems on industrial and commercial products where it is desired to avoid the use of threaded connectors.
Hydraulic fluid power - Flange connections with split or one-piece flange clamps and metric or inch screws - Part 2: Flange connectors, ports and mounting surfaces for use at a pressure of 42 MPa (420 bar), DN 13 to DN 76
- ICS
- 23.100.40
- CCS
- J15
- 发布
- 2018-03-01
- 实施
This standard is intended to be used for rubber and plastic hose assemblies of the types: 1ST, 1SN, 2ST and 2SN according to DIN EN 853, 1TE, 2TE and 3TE according to DIN EN 854, 4SP, 4SH, R13 according to DIN EN 856, R15 according to ISO 3862 and 1SC and 2SC according to DIN EN 857 as well as plastic hoses assemblies of the types R7, R8 and R18 according to ISO 3949, appropriate for temperatures of -40° C up to + 100° C (hose types R13 and R 15 to 120°C) and hose connectors of the light and heavy duty series according to DIN ISO 12151-2 and DIN ISO 12151-3. This standard contains information about the most important criteria for selection and reference of hoses and connectors, the installation and connection dimensions as well as the requirements for the installation of hose assemblies. The comparative presentation of respective hoses types in Table 1 and Table 2 gives designers guidelines for the selection of hoses (nominal diameter and design) and their appropriate connectors, in case the piping of a system has already been determined. Further, guidelines are given in this standard for storage, life cycle and necessary inspections to ensure the full functionality of those assemblies.
Hydraulic fluid power - Hose assemblies - Dimensions, requirements
- ICS
- 23.100.40
- CCS
- P94
- 发布
- 2018-03-01
- 实施
本标准规定了工程机械液压管路的术语、定义、布置美观性、安全性及维修性等。 本标准适用于工程机械产品液压管路的布局,其它产品的液压管路布局可参照执行。
Specification for hydraulic piping layout of construction machinery
- ICS
- 23.100.40
- CCS
- J15
- 发布
- 2017-12-29
- 实施
- 2017-12-29
This part of ISO 15171 specifies dimensions, performance requirements, and test procedures for diagnostic couplings with an M16 x 2 connection end that can be connected under pressure without tools to a maximum pressure of 40 MPa (400 bar) providing following stud ends: ISO 6149-2 - M14 x 1,5; ISO 9974-2 - M14 x 1,5; ISO 1179-2 - G 1/4; ISO 11926-2 - 7/16-20 UNF. The dimensions of the coupler counterpart are specified. The coupling is designed for use in hydraulic systems that use mineral oils. Couplings in accordance with this part of ISO 15171 may be used at a maximum working pressure of 63 MPa (630 bar).
Connections for fluid power and general use - Hydraulic couplings for diagnostic purposes - Part 2: Coupling with M16 x 2 end for connection under pressure (ISO 15171-2:2016)
- ICS
- 23.100.40
- CCS
- J15
- 发布
- 2017-12-01
- 实施
This standard is intended to be used for rubber and plastic hose assemblies of the types: 1ST, 1SN, 2ST and 2SN according to DIN EN 853, 1TE, 2TE and 3TE according to DIN EN 854, 4SP, 4SH, R13 according to DIN EN 856, R15 according to ISO 3862 and 1SC and 2SC according to DIN EN 857 as well as plastic hoses assemblies of the types R7, R8 and R18 according to ISO 3949, appropriate for temperatures of -40° C up to + 100° C (hose types R13 and R 15 to 120°C) and hose connectors of the light and heavy duty series according to DIN ISO 12151-2 and DIN ISO 12151-3. This standard contains information about the most important criteria for selection and reference of hoses and connectors, the installation and connection dimensions as well as the requirements for the installation of hose assemblies. The comparative presentation of respective hoses types in Table 1 and Table 2 gives designers guidelines for the selection of hoses (nominal diameter and design) and their appropriate connectors, in case the piping of a system has already been determined. Further, guidelines are given in this standard for storage, life cycle and necessary inspections to ensure the full functionality of those assemblies.
Hydraulic fluid power - Hose assemblies - Dimensions, requirements
- ICS
- 23.100.40
- CCS
- P94
- 发布
- 2017-11-01
- 实施
Connectors for fluid power and general use - Assembly instructions for connectors with adjustable stud ends and O-ring sealing
- ICS
- 23.100.40
- CCS
- 发布
- 2017-10-27
- 实施
Connections for fluid power and general use. Ports and stud ends with ISO 261 metric threads and O-ring sealing. Dimensions, design, test methods and requirements for external hex and internal hex port plugs
- ICS
- 23.100.40
- CCS
- J15
- 发布
- 2017-10-05
- 实施
- 2017-10-31
Connections for fluid power and general use - Ports and stud ends with ISO 261 metric threads and O-ring sealing - Part 4: Dimensions@ design@ test methods and requirements for external hex and internal hex port plugs
- ICS
- 23.100.40
- CCS
- 发布
- 2017-09-01
- 实施
This document specifies dimensions and performance requirements for external hex and internal hex port plugs for use with ISO 6149-1 ports. Port plugs in accordance with this document can be used at working pressures up to 63 MPa (630 bar1)). The permissible working pressure depends upon the plug end size, materials, design, working conditions, application, etc. Conformance to the dimensional information in this document does not guarantee rated performance. Each manufacturer is expected to perform testing according to the specification contained in this document to assure that components comply with the performance ratings. WARNING — The use of stud ends conforming to this document with ports conforming to the relevant parts of ISO 1179, ISO 9974 and ISO 11926 could lead to a hazardous situation.
Connections for fluid power and general use — Ports and stud ends with ISO 261 metric threads and O-ring sealing — Part 4: Dimensions, design, test methods and requirements for external hex and intern
- ICS
- 23.100.40
- CCS
- 发布
- 2017-08-09
- 实施
Pneumatic fluid power -- Connections -- Ports and stud ends
- ICS
- 23.100.40
- CCS
- J15;J20
- 发布
- 2017-05-22
- 实施
Connections for general use and fluid power. Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing. Dimensions, design, test methods and requirements for external hex and internal hex port plugs
- ICS
- 23.100.40
- CCS
- J15
- 发布
- 2016-12-31
- 实施
- 2016-12-31
This International Standard specifies sizes and nominal working pressures for tubes with outside diameters in accordance with ISO 4397 and wall thicknesses or mechanical properties in accordance with ISO 3304 (seamless precision steel tubes) and ISO 3305 (welded precision steel tubes). The nominal working pressures included in this standard reflect a design factor ratio of 4 to 1 between the static burst and nominal working pressures.
Hydraulic fluid power -- Plain-end, seamless and welded precision steel tubes -- Dimensions and nominal working pressures
- ICS
- 23.100.40
- CCS
- 发布
- 2016-12-22
- 实施
This part of ISO 7241 specifies different test methods which could be applied to quick-action couplings. NOTE Users of this part ISO 7241 may select only the tests applicable to their needs. It is not intended that all tests be carried out for every application. This part of ISO 7241 is applicable to male and female coupling halves, complete couplings, couplings with and without sealing means when uncoupled, and couplings that are connected and disconnected by a linear and/or rotational motion.
Hydraulic fluid power -- Quick-action couplings -- Part 2: Test methods
- ICS
- 23.100.40
- CCS
- 发布
- 2016-12-22
- 实施
