23.100.40 管道和管接头 标准查询与下载
共找到 485 条与 管道和管接头 相关的标准，共 33 页
This International Standard specifies the interface dimensions and basic performance requirements for two series of hydraulic quick-action couplings. Both series are in widespread use and have similar technological advantages. Series A is used predominantly in Europe and is preferred worldwide for agricultural and forestry machinery, and this International Standard also specifies additional requirements for Series A for use in agricultural machinery applications covered in ISO 5675. Series B is used predominantly in North America and in the chemical industry.
Hydraulic fluid power -- Dimensions and requirements of quick-action couplings
- ICS
- 23.100.40
- CCS
- 发布
- 2016-12-22
- 实施
This International Standard specifies sizes and nominal working pressures for tubes with outside diameters in accordance with ISO 4397 and wall thicknesses or mechanical properties in accordance with ISO 3304 (seamless precision steel tubes) and ISO 3305 (welded precision steel tubes). The nominal working pressures included in this standard reflect a design factor ratio of 4 to 1 between the static burst and nominal working pressures.
Hydraulic fluid power -- Plain-end, seamless and welded precision steel tubes -- Dimensions and nominal working pressures
- ICS
- 23.100.40
- CCS
- 发布
- 2016-12-22
- 实施
1.1 This specification establishes the performance characteristics required for Metallic Press-Connect Fittings for use in piping and tubing systems with a maximum allowable working pressure of three-hundred pounds per square inch (300 psi). These fittings directly attach to pipe or tube by mechanical deformation of the pipe or tube or fitting, or a combination thereof, creating a seal and a restrained joint. The seal may be created via the mechanical deformation (of the pipe, tube or fitting) or created independently. Successful completion of the tests described herein constitutes completion of the technical portion of the qualification process. 1.2 The tests specified are applicable only to ascertain the performance characteristics. These tests are not intended for use in the evaluation of non-Press-Connect Fittings. 1.3 Refer to IACS UR P2.7.4, Table-7 for Metallic PressConnect Fittings applications. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Specification for Metallic Press-Connect Fittings for Piping and Tubing Systems
- ICS
- 23.100.40
- CCS
- 发布
- 2016-12-15
- 实施
Connections for general use and fluid power - Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing - Part 4: Dimensions, design, test methods and requirements for external hex and internal hex port plugs
- ICS
- 23.100.40
- CCS
- J13
- 发布
- 2016-12-01
- 实施
Connectors for fluid power and general use — Designation and nomenclature
- ICS
- 23.100.40
- CCS
- 发布
- 2016-09-02
- 实施
Ruber hoses and hose assemblies - Rubber-covered spiral wire reinforced hydraulic type - Specification; German version EN 856:2015
- ICS
- 23.100.40
- CCS
- G42
- 发布
- 2016-09
- 实施
Rubber hoses and hose assemblies - Wire braid reinforced compact type for hydraulic applications - Specification; German version EN 857:2015
- ICS
- 23.100.40
- CCS
- G42
- 发布
- 2016-09
- 实施
Connections for fluid power and general use. Hydraulic couplings for diagnostic purposes. Coupling with M16 x 2 end for connection under pressure
- ICS
- 23.100.40
- CCS
- J20
- 发布
- 2016-02-29
- 实施
- 2016-02-29
This part of ISO 15171 speci fies dimensions, performance requirements, and test procedures for diagnostic couplings with an M16 × 2 connection end that can be connected under pressure without tools to a maximum pressure of 40 MPa (400 bar) providing following stud ends: — The dimensions of the coupler counterpart are speci fied. The coupling is designed for use in hydraulic systems that use mineral oils. NOTE The use of this coupling with fluids other than mineral oil requires an agreement between the supplier and the purchaser. Couplings in accordance with this part of ISO 15171 may be used at a maximum working pressure of 63 MPa (630 bar) . The working pressure depends upon the materials, design, working conditions, application, etc.
Connections for fluid power and general use - Hydraulic couplings for diagnostic purposes - Part 2: Coupling with M16 x 2 end for connection under pressure
- ICS
- 23.100.40
- CCS
- J20
- 发布
- 2016-02
- 实施
Scope is not provided for this standard
Hydraulic fluid power -- Dimensions and requirements for screw-to-connect quick-action couplings for general purpose
- ICS
- 23.100.40
- CCS
- 发布
- 2015-12-21
- 实施
Scope is not provided for this standard
Connections for general use and fluid power -- Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing -- Part 3: Light-duty (L series) stud ends with sealing by O-ring with retaining ring (types G and H)
- ICS
- 23.100.40
- CCS
- 发布
- 2015-12-21
- 实施
Scope is not provided for this standard
Connections for general use and fluid power -- Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing -- Part 2: Heavy-duty (S series) and light-duty (L series) stud ends with elastomeric sealing (type E)
- ICS
- 23.100.40
- CCS
- 发布
- 2015-12-21
- 实施
Scope is not provided for this standard
Hydraulic fluid power -- Flush-face type, quick-action couplings for use at pressures of 20 MPa (200 bar) to 31,5 MPa (315 bar) -- Specifications
- ICS
- 23.100.40
- CCS
- 发布
- 2015-12-21
- 实施
GSO ISO 1179-4:2015 一般用途和流体动力连接 端口和螺栓端部带有符合 ISO 228-1 标准的弹性体和金属对金属冲压螺纹 第4部分：仅采用金属对金属冲压的一般用途螺栓端部（ B型）
Scope is not provided for this standard
Connections for general use and fluid power -- Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing -- Part 4: Stud ends for general use only with metal-to-metal sealing (type B)
- ICS
- 23.100.40
- CCS
- 发布
- 2015-12-21
- 实施
Scope is not provided for this standard
Connections for general use and fluid power -- Ports and stud ends with ISO 725 threads and O-ring sealing -- Part 2: Heavy-duty (S series) stud ends
- ICS
- 23.100.40
- CCS
- 发布
- 2015-12-21
- 实施
Scope is not provided for this standard
Hydraulic fluid power -- Dimensions and requirements for screw-to-connect quick-action couplings for use at a pressure of 72 MPa (720 bar)
- ICS
- 23.100.40
- CCS
- 发布
- 2015-12-21
- 实施
Scope is not provided for this standard
Pneumatic fluid power -- Push-in connectors for thermoplastic tubes
- ICS
- 23.100.40
- CCS
- 发布
- 2015-12-21
- 实施
Scope is not provided for this standard
Connections for general use and fluid power -- Ports and stud ends with ISO 725 threads and O-ring sealing -- Part 1: Ports with O-ring seal in truncated housing
- ICS
- 23.100.40
- CCS
- 发布
- 2015-12-21
- 实施
Scope is not provided for this standard
Connections for general use and fluid power -- Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing -- Part 1: Threaded ports
- ICS
- 23.100.40
- CCS
- 发布
- 2015-12-21
- 实施
Scope is not provided for this standard
Rubber hoses and hose assemblies -- Rubber-covered spiral-wire-reinforced hydraulic types for oil-based or water-based fluids -- Specification
- ICS
- 23.100.40
- CCS
- 发布
- 2015-12-21
- 实施
