23.100.50 控制部件 标准查询与下载

ISO 7789:2007 液压传动.二通、三通和四通螺纹式插装阀.插装孔

This International Standard specifies the dimensions and provides other data relating to cavities in which two-, three- and four-port, screw-in cartridge valves are mounted in order to ensure interchangeability. It is applicable to two-, three- and four-port screw-in cartridge valves generally used in industrial and mobile equipment.

Hydraulic fluid power - Two-, three- and four-port screw-in cartridge valves - Cavities

DIN ISO 20401:2007 气动液压传动系统.方向控制阀.直径为8mm～12mm的圆形电连接器的管脚分配规范(ISO 20401-2005+勘误1-2005)

This International Standard specifies the pin assignment for pneumatic directional control valves when used together with electrical connectors according to IEC 60947-5-2. This definition is valid for connectors as shown in Figures D.2 and D.4 of IEC 60947-5-2:2004, which are shown in a simplified version below: --- Figure D.2: 12-mm diameter, five-pin connector (pin 5, not shown, is unassigned), male face view -- Figure D.4: 8-mm diameter, four-pan connector, male face view

Pneumatic fluid power systems - Directional control valves - Specification of pin assignment for electrical round connectors of diameters 8 mm and 12 mm (ISO 20401:2005 + Cor. 1:2005) English version of DIN ISO 20401:2007-07

ISO 5599-2:2001/Cor 1:2007 气动液压.五端口定向控制阀.第2部分:带可选接线盒的安装接口表面

This is Technical Corrigendum 1 to ISO 5599-2-2001 (Pneumatic fluid power — Five-port directional control valves — Part 2: Mounting interface surfaces with optional electrical connector)

Pneumatic fluid power - Five-port directional control valves - Part 2: Mounting interface surfaces with optional electrical connector; Technical Corrigendum 1

ISO 5599-1:2001/cor 1:2007 气动液压动力.五端口定向控制阀.第1部分:无接线盒的安装接口表面

The standard is about Pneumatic fluid power — Five-port directional control valves — Part 1: Mounting interface surfaces without electrical connector TECHNICAL CORRIGENDUM 1

Pneumatic fluid power - Five-port directional control valves - Part 1: Mounting interface surfaces without electrical connector; Technical Corrigedum 1

JIS B 8668:2006 液压流体动力.双口剖分筒形插装式阀门.阀腔

この規格は，2ポート形スリップイン式カートリッジ弁が互換性をもって確実に組み込まれるために,その取付面及び取付穴寸法について規定する。

Hydraulic fluid power -- Two-port slip-in cartridge valves -- Cavities

JIS B 8669:2006 液压流体动力.阀门孔口、底板、控制装置和螺线管的标识

この規格は,油圧システムに用いるバルブ，サブプレート，マニホールドブロックのポート及びソレノイドの識別記号について規定する。この規格は，現在バルブポートのマーキングが異なっている2又は3ポートをもったバルブを，将来開発しようとする場合に適用する。

Hydraulic fluid power -- Identification of valve ports, subplates, control devices and solenoids

KS B ISO 16874-2006(2011) 液压传动歧管组件及其部件的识别

Hydraulic fluid power－Identification of manifold assemblies and their components

KS B ISO 15218-2006(2011) 气动流体动力－3/2电磁阀－安装界面

Pneumatic fluid power－3/2 solenoid valves－Mounting interface surfaces

KS B ISO 17082-2006(2011) 气动流体动力－阀门－供应商资料中包含的数据

Pneumatic fluid power－Valves－Data to be included in supplier literature

KS B ISO 16873-2006(2011) 液压传动－压力开关－安装面

Hydraulic fluid power－Pressure switches－Mounting surfaces

ISO 6953-1:2000/cor 1:2006 气压传动.压缩空气调压阀和带过滤器的调压阀.第1部分:商务文件中包含的主要特性和产品标识要求.技术勘误1

This is Technical Corrigendum 1 to ISO 6953-1-2000 (Pneumatic fluid power — Compressed air pressure regulators and filter-regulators — Part1: Main characteristics to be included in literature from suppliers and product-marking requirements)

Pneumatic fluid power - Compressed air pressure regulators and filter-regulators - Part 1: Main characteristics to be included in literature from suppliers and product-marking requirements; Technical Corrigendum 1

DIN ISO 5599-1:2005 气压传动.五气口方向控制阀.第1部分:不带电接头的安装面

This part of ISO 5599 specifies the requirements for a mounting interface surface without electrical connector for five- port pneumatic directional control valves, for use at a maximum rated pressure of 1,6 MPa [16 bari)]. It gives -- dimensions and tolerances of the interface features, -- port identification, and -- identification of the result of control-mechanism actuation. It is not applicable to the functional characteristics of interfaces.

Pneumatic fluid power - Five-port directional control valves - Part 1: Mounting interface surfaces without electrical connector (ISO 5599-1:2001);English version of DIN ISO 5599-1:2005

DIN ISO 12238:2005 液压传动.方向控制阀门.移动时间测量(ISO 12238-2001)

This standard - specifies test procedures for measuring the shifting times of electrically- or pneumatically-operated directional control valves and moving-part logic elements, - establishes a definition for shifting time, and - is intended to improve the application of pneumatic fluid power by providing users and manufacturers of pneumatic valves with a standardized test procedure for measuting the shifting time.

Pneumatic fluid power - Directional control valves - Measurement of shifting time (ISO 12238:2001);English version of DIN ISO 12238:2005

BS ISO 4401:2005 液压流体动力.四孔定向控制阀.安装面

This International Standard specifies the dimensions and other data relating to surfaces on which four-port hydraulic directional control valves are mounted in order to ensure their interchangeability. It applies to mounting surfaces for four-port hydraulic directional control valves which represent current practice. They are generally applicable to industrial equipment.

Hydraulic fluid power - Four-port directional control valves - Mounting surfaces

ISO 20401:2005/cor 1:2005 气动液压驱动系统.方向控制阀.直径在8mm到12mm的圆形电连接器管脚分布的规范.技术勘误1

This is Technical Corrigendum 1 to ISO 20401-2005 (Pneumatic fluid power systems-Directional control valves-Specification of pin assignment for electrical round connectors of diameters 8 mm and 12 mm)

Pneumatic fluid power systems - Directional control valves - Specification of pin assignment for electrical round connectors of diameters 8 mm and 12 mm; Technical Corrigendum 1

ISO 4401:2005 液压传动.四油口定向控制阀.装配面

This International Standard specifies the dimensions and other data relating to surfaces on which four-port hydraulic directional control valves are mounted in order to ensure their interchangeability. It applies to mounting surfaces for four-port hydraulic directional control valves which represent current practice. They are generally applicable to industrial equipment.

Hydraulic fluid power - Four-port directional control valves - Mounting surfaces

KS B ISO 15407-1-2005(2010) 气动流体动力－尺寸为18mm和26mm的五通定向控制阀－第1部分:不带电气连接器的安装界面

Pneumatic fluid power－Five-port directional control valves,sizes 18 mm and 26 mm－Part 1：Mounting interface surfaces without electrical connector

KS B ISO 12238-2005(2010) 气动流体动力方向控制阀移动时间的测量

Pneumatic fluid power－Directional control valves－Measurement of shifting time

KS B ISO 7368-2005(2010) 液压传动二通插装阀腔

Hydraulic fluid power－Two-port slip-in cartridge valves－Cavities

KS B ISO 15407-2-2005(2010) 气动流体动力－尺寸为18mm和26mm的五通定向控制阀－第2部分:带可选电气连接器的安装接口面

Pneumatic fluid power－Five-port directional control valves,sizes 18 mm and 26 mm－Part 2：Mounting interface surfaces with optional electrical connector