23.100.50 控制部件 标准查询与下载

ISO 5599-3:1990 气压传动 五气口方向控制阀 第3部分:表示阀功能的标注方法

This part specifies the codification system to be used for communication purposes. Defines functions of valve operators used on the various sizes of mounting surfaces complying with the requirements of ISO 5599-1. This codification system is not to be applied directly to the product as is does not describe the many attributes which affect performance interchangeability.

Pneumatic fluid power; five-port directional control valves; part 3: code system for communication of valve functions

ANSI/NFPA T3.21.8-1990 气动.反应时间的测量.方向控制阀门

Pneumatic Fluid Power - Measurement of Response Time - Directional Control Valves

ANSI/NFPA T3.21.15-1990 气动.螺线管,螺线管头,控制装置和阀门孔小板块标记

This standard includes conventions to be used with pneumatic fluid power directional control valves having 2, 3, 4 and 5 flow path connections for the following; Identification of pneumatic connecting ports; Identification of valve operators; and Correlation of electrical interface connections with appropriate operators in electrically operated valves.

Pneumatic Fluid Power - Marking of Valve Ports Subplates, Control Devices, Solenoids, and Solenoid Leads

ISO 5599-1:1989 气压传动.五通定向控制阀.第1部分:不带电连接器的安装接口表面

Pneumatic fluid power; five-port directional control valves; part 1: mounting interface surfaces without electrical connector

ISO 7368:1989 液压传动 二油口盖板式插装阀 插装孔

Specifies the dimensions and other data relating to cavities in which valves are mounted in order to ensure interchangeability. Applies to cavities for valves which are generally applicable to industrial equipment. The corresponding dimensions and sketches are given and illustrated in the figures 1 to 14. The informative annex A contains the bibliography.

Hydraulic fluid power; two-port slip-in cartridge valves; cavities

NF E48-423:1989 液压传动.4孔分配器,压力控制阀.顺序阀,卸载阀,节流阀,止回阀, 流量补偿阀,卸压阀.安装面

HYDRAULIC FLUID POWER. FOUR-PORT DIRECTIONAL CONTROL VALVES,PRESSURE-CONTROL VALVES,SEQUENCE VALVES,UNLOADING VALVES,THROTTLE VALVES,CHECK VALVES,COMPENSATED FLOW-CONTROL VALVES,PRESSURE-RELIEF VALVE. MOUNTING SURFACE.

ISO 6403:1988 液压传动 控制流量及压力的阀 试验方法

Specifies methods for testing valves which are used in a circuit in order to determine their steady-state and dynamic performance. Requirements for test installations and procedures, measurements and presentation of results are specified. Does not establish limits of performance. Accuracy of measurement is divided into three classes (A, B and B) which are explained in annex A. Guidance as to the use of practical units for the presentation of results is given in annex B.

Hydraulic fluid power; valves controlling flow and pressure; test methods

ANSI B93.112M-1988 液压气动阀内部漏泄特性的测定方法

Specifies procedures for the determination of leakage characteristics of any fluid power valve, and is intended to provide a uniform laboratory procedure for obtaining and reporting the fluid flow across a valve element that is considered blocked.

Hydraulic Fluid Power - Valves - Method for Determining the Internal Leakage Characteristics

ANSI B93.77M-1987 液压气动缸传动安装阀安装表面的标准尺寸

Hydraulic Fluid Power - Cylinder Actuator Mounted Valves - Standard Dimensions for Mounting Surfaces

GOST 21324-1983 Phom=1MPa(≈10kgf/cm⒉)气动止回阀.技术条件

Air check valves for nominal pressure 1 MPa ( 10 kgf/sq sm). Specifications

GOST 26005-1983 Phom 32MPa(3200kgf/cm⒉)以内的压力继电器.技术条件

Настоящий стандарт распространяется на реле давления плунжерного типа, предназначенные для контроля давления рабочей среды в гидравличе

Pressure switches for Pnom up to 320 MPa (320 kgf/sq cm). Specifications

DIN 24340-2:1982 液压阀.换向阀用安装面和连接板

Hydraulic valves; mounting surfaces and connecting plates for directional control valvesZusammenhang mit dem von der International Organization for Standardization (ISO) herausgegebenen Internationalen Norm-Entwurf ISO/DIS 4401-1980. siehe Erl?uterungen

Hydraulic valves; mounting surfaces and connecting plates for directional control valves

GOST 24679-1981 Phom为32MPa四线阀式液压分配器.技术条件

Настоящий стандарт распространяется на золотниковые четырехлинейные гидрораспределители типа В на Рном до 32 МПа (320 кгс/см.кв.) со стыковы

Hydraulic four-way control valves for nominal pressure to 32 MPa. Specifications

ISO/DIS 6953-2 气动流体动力“压缩空气压力调节器和过滤调节器”第2部分：确定供应商文献中包含的主要特性的测试方法

Pneumatic fluid power — Compressed air pressure regulators and filter-regulators — Part 2: Test methods to determine the main characteristics to include in supplier’s literature

ISO/DIS 6953-1 气动流体动力“压缩空气压力调节器和过滤调节器”第1部分：供应商文献和产品标记要求中包含的主要特性

Pneumatic fluid power — Compressed air pressure regulators and filter-regulators — Part 1: Main characteristics to include in supplier's literature and product-marking requirements

BS 4151:1967 输入信号为 3至15磅/平方英寸(压力计)的气动阀定位器的评定方法

Specifies tests to determine performance of pneumatic valve positioners with 3 to 15 lbf/in2 (gauge) input signal. Method of evaluation specifies use of a valve operator of a spring-opposed or double-acting diaphragm or piston type in order to allow a ready comparison to be made between different types of positioner.

Method of evaluating pneumatic valve positioners with input signal of 3 to 15 lbf/in2 (gauge)