23.100.50 控制部件 标准查询与下载
共找到 356 条与 控制部件 相关的标准，共 24 页
Pneumatic fluid power — Compressed air pressure regulators and filter-regulators — Part 1: Main characteristics to include in supplier's literature and product-marking requirements
- ICS
- 23.100.50
- CCS
- 发布
- 2023-07
- 实施
Pneumatic fluid power — Compressed air pressure regulators and filter-regulators — Part 2: Test methods to determine the main characteristics to include in supplier’s literature
- ICS
- 23.100.50
- CCS
- 发布
- 2023-07
- 实施
5 技术要求 型式和尺寸 螺纹连接油口的型式和尺寸应符合GB/T 2878.1的规定。 外观质量 应在转向调节器的所有连接油口附近清晰标注表示该油口功能的符号。 转向调节器的外露非加工表面的涂层应均匀，色泽一致，喷涂前处理不应涂腻子。 表面不应有划伤、裂痕。 性能要求 5.3.1 动作性能 在额定工况下，转向调节器左右活塞杆离合器行程、刹车行程内动作正常，复位灵敏。 5.3.2 压力性能 在额定工况下，左右腔压力应不小于3 MPa。 5.3.3 工作性能 在额定工况下动作，转向调节器应达到转向所需的离合器行程，手动推动后置推杆，转向调节器应达到转向所需的刹车行程。 5.3.4 密封性能 在额定工况下，转向调节器静密封处应不渗漏，动密封处应不成滴。 5.3.5 耐高温性能 经100℃加温试验后，转向调节器各零部件应正常工作，与机体连接的安装面处无渗漏。 5.3.6 耐压性能 转向调节器的各承压油口应能承受该油口公称压力的1.5 倍，不得有外渗漏及零件损坏等现象。 5.3.7 耐久性能 在额定工况下，转向调节器动作80 万次数后，其零件不应有异常磨损和其他形式的损坏。 5.3.8 噪声 在额定工况下，噪声应不大于80 dB(A)。
Hydraulic assisted steering regulator
- ICS
- 23.100.50
- CCS
- C344
- 发布
- 2023-04-06
- 实施
- 2023-04-06
5 技术要求 型式和尺寸 螺纹连接油口的型式和尺寸应符合GB/T 2878.1的规定。 外观质量 应在分流阀的所有连接油口附近清晰标注表示该油口功能的符号。 分流阀的外露非加工表面的涂层应均匀，色泽一致，喷涂前处理不应涂腻子。 表面不应有划伤、裂痕。 内部清洁度 分流阀的内部清洁度应符合JB/T 7858的规定。 性能要求 5.4.1 溢流阀开启压力 分流阀的溢流阀压力在规定的安全压力的95%～105%压力范围内应正常开启。 5.4.2 分流性能 在额定流量范围内，分流阀通过两路油口的流量比例公差为5%。 5.4.3 密封性能 在额定工况下，分流阀静密封处应不渗漏，动密封处应不成滴。 5.4.4 耐高温性能 经80℃加温试验后，分流阀各零部件应正常工作，与机体连接的安装面处无渗漏。 5.4.5 耐压性能 分流阀的各承压油口应能承受该油口公称压力的1.5 倍，不得有外渗漏及零件损坏等现象。 5.4.6 耐久性能 在额定工况下，分流阀动作20 万次数后，其零件不应有异常磨损和其他形式的损坏，分流流量比例公差值应不低于10%。 5.4.7 噪声 在额定工况下，噪声应不大于80 dB(A)。
High speed cartridge shunt control valve
- ICS
- 23.100.50
- CCS
- C344
- 发布
- 2023-04-06
- 实施
- 2023-04-06
性能要求 5.2.1 耐压性能 集成阀在1.5 倍的公称压力下，不得有外渗漏及零件损坏等现象。 5.2.2 内泄漏性能 被试集成阀在输入公称压力与流量的条件下，主滑阀杆处于上升位时，泄漏油口输出流量应不大于20 ml/min。 5.2.3 保压性能 集成阀在阀杆处于中立位置时，出油口的压力在2 分钟内下降应不大于1 MPa。 5.2.4 保压区间 在额定工况下，集成阀的保压区间应在1 mm～2 mm可调。 5.2.5 操纵性能 在额定工况下，集成阀连续动作无卡紧，操纵力应在50 N～100 N。 5.2.6 密封性能 在额定工况下，集成阀静密封处应不渗漏，动密封处应不成滴。 5.2.7 耐高温性能 经110℃加温试验后，集成阀各零部件应正常工作，与机体连接的安装面处无渗漏。 5.2.8 耐久性能 在额定工况下，集成阀动作20 万次数后，其零件不应有异常磨损和其他形式的损坏，内泄漏性能和保压性能的下降值不应超过规定值的5%。 5.2.9 噪声 在额定工况下，噪声应不大于80 dB(A)。
Built-in pressure feedback control integrated valve
- ICS
- 23.100.50
- CCS
- C344
- 发布
- 2023-04-06
- 实施
- 2023-04-06
5 技术要求 型式和尺寸 螺纹连接油口的型式和尺寸应符合GB/T 2878.1的规定。 外观质量 应在液压缸的所有连接油口附近清晰标注表示该油口功能的符号。 液压缸的外露非加工表面的涂层应均匀，色泽一致，喷涂前处理不应涂腻子。 表面不应有划伤、裂痕。 内部清洁度 液压缸的内部清洁度应符合JB/T 7858的规定。 性能要求 5.4.1 最低启动压力 液压缸的最低启动压力应不大于0.3 MPa。 5.4.2 加载阀调定性能 液压缸加压至加载阀调定压力时，加载阀应正常开启，油液应从液压缸一腔流至另一腔中。 5.4.3 内泄漏量 10 min内液压缸由内泄漏引起的活塞移动量应不大于1 mm。 5.4.4 密封性能 在额定工况下，液压缸静密封处应不渗漏，动密封处应不成滴。 5.4.5 耐高温性能 经80℃加温试验后，液压缸各零部件应正常工作。 5.4.6 耐压性能 液压缸的各承压油口在承受公称压力的1.25 倍时，不应有外泄漏、零件损坏等现象。 5.4.7 耐久性能 在额定工况下，液压缸动作20 万次后，其零件不应有异常磨损和其他形式的损坏，内泄漏量指标下降不应超过规定值的5%。
Rail guided vehicle（RGV）cylinder valve system
- ICS
- 23.100.50
- CCS
- C348
- 发布
- 2023-04-06
- 实施
- 2023-04-06
1 Scope This document specifies test procedures for measuring the shifting times of electrically or pneumatically operated directional control valves. It is applicable to monostable and bistable pneumatic directional control valves, with 2 or 3 position functions.
Pneumatic fluid power. Directional control valves. Measurement of shifting time
- ICS
- 23.100.50
- CCS
- 发布
- 2023-02-28
- 实施
- 2023-02-28
This document specifies test procedures for measuring the shifting times of electrically or pneumatically operated directional control valves. It is applicable to monostable and bistable pneumatic directional control valves, with 2 or 3 position functions.
Pneumatic fluid power — Directional control valves — Measurement of shifting time
- ICS
- 23.100.50
- CCS
- 发布
- 2023-02-16
- 实施
- 2023-02
Pneumatic fluid power — Compressed air pressure regulators and filter-regulators — Part 1: Main characteristics to include in supplier's literature and product-marking requirements
- ICS
- 23.100.50
- CCS
- 发布
- 2023-01
- 实施
本文件规定了气动多针阀岛的术语和定义、 基本要求、 技术要求、 试验方法、 检验规则、 标志、 包装、 运输、 贮存和质量承诺。 本文件适用于以压缩空气为工作介质，额定工作压力0.63 MPa，工作电压为直流24 V，电磁阀公称通径不大于6 mm的气动多针阀岛（以下简称阀岛）。
Pneumatic multi-pin valve terminal
- ICS
- 23.100.50
- CCS
- C344
- 发布
- 2022-12-08
- 实施
- 2023-03-22
本文件规定了常规液压控制阀“领跑者”标准评价的评价指标体系和评价方法及等级划分。 本文件适用于常规液压控制阀的产品质量分级及企业标准水平评价。相关机构在制定企业标准“领跑者”评估方案时可参照使用。企业在制定企业标准时可参照使用。
Assessment requirements for quality grading and forerunner — on-off hydraulic control valve
- ICS
- 23.100.50
- CCS
- C344
- 发布
- 2022-09-06
- 实施
- 2022-09-12
本文件规定了中小型工程机械液压系统用直驱电控多路换向阀（以下简称“换向阀”）的型号、基本参数和标记、要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于公称压力35 MPa，额定流量为60 L/min的中小型工程机械液压系统用换向阀。
Direct drive electronically controlled multiple directional valves for hydraulic systems of small and medium construction machinery
- ICS
- 23.100.50
- CCS
- C344
- 发布
- 2022-08-17
- 实施
- 2022-08-22
Measuring methods for coefficient of discharge of safety valves
- ICS
- 23.100.50
- CCS
- 发布
- 20220602
- 实施
- 20220602
Hydraulic fluid power -- Compensated flow-control valves -- Mounting surfaces
- ICS
- 23.100.50
- CCS
- 发布
- 2022-03-22
- 实施
Pneumatic fluid power -- Compressed air pressure regulators and filter-regulators -- Part 2: Test methods to determine the main characteristics to be included in literature from suppliers
- ICS
- 23.100.50
- CCS
- 发布
- 2022-02-21
- 实施
Pneumatic fluid power -- Compressed air pressure regulators and filter-regulators -- Part 3: Alternative test methods for measuring the flow-rate characteristics of pressure regulators
- ICS
- 23.100.50
- CCS
- 发布
- 2022-02-21
- 实施
Pneumatic fluid power -- Compressed air pressure regulators and filter-regulators -- Part 1: Main characteristics to be included in literature from suppliers and product-marking requirements
- ICS
- 23.100.50
- CCS
- 发布
- 2022-02-21
- 实施
1 Scope This document specifies which characteristics of electro-pneumatic continuous pressure control valves are to be included in the supplier's literature. In accordance with ISO 5598, these control valves include: — electrically modulated pneumatic proportional pressure valves, — proportional pressure control valves without electronic pressure feedback, and — proportional pressure control valves with electronic pressure feedback. This document is limited to the characterization of components with an exhaust port to the atmosphere. NOTE 1 The characteristics of non-electrically modulated pneumatic pressure control valves are specified in ISO 6953‑1. NOTE 2 The characteristics of electro-pneumatic continuous flow control valves are specified in ISO 10041‑1.
Pneumatic fluid power. Electro-pneumatic pressure control valves. Main characteristics to include in the supplier's literature
- ICS
- 23.100.50
- CCS
- 发布
- 2021-11-30
- 实施
- 2021-11-30
1 Scope This document specifies the test procedures and a method of presenting results concerning the parameters which define the main characteristics to be included in the supplier's literature of the electro-pneumatic continuous pressure control valves, conforming to ISO 10094‑1. The purpose of this document is: — to facilitate comparison by standardizing the test methods and the presentation of the test results, and — to assist in the proper application of these components in compressed air systems. The specified tests are intended to allow comparison between the different types of continuous pressure control valves; these are not production tests to be carried out on each manufactured product. The tests described in this document are for components with an exhaust port vented to the atmosphere. NOTE 1 The tests related to non-electrically modulated pneumatic continuous pressure control valves are specified in ISO 6953‑2. NOTE 2 The tests related to electro-pneumatic continuous flow control valves are specified in ISO 10041‑2. NOTE 3 ISO 6953‑3 provides an alternate dynamic test method for flow-rate characteristics using an isothermal tank instead of a flow meter. However, this method measur...
Pneumatic fluid power. Electro-pneumatic pressure control valves. Test methods to determine main characteristics to include in the supplier's literature
- ICS
- 23.100.50
- CCS
- 发布
- 2021-11-30
- 实施
- 2021-11-30
This document specifies the test procedures and a method of presenting results concerning the parameters which define the main characteristics to be included in the supplier's literature of the electro-pneumatic continuous pressure control valves, conforming to ISO 10094-1. The purpose of this document is: — to facilitate comparison by standardizing the test methods and the presentation of the test results, and — to assist in the proper application of these components in compressed air systems. The specified tests are intended to allow comparison between the different types of continuous pressure control valves; these are not production tests to be carried out on each manufactured product. The tests described in this document are for components with an exhaust port vented to the atmosphere. NOTE 1 The tests related to non-electrically modulated pneumatic continuous pressure control valves are specified in ISO 6953-2. NOTE 2 The tests related to electro-pneumatic continuous flow control valves are specified in ISO 10041-2. NOTE 3 ISO 6953-3 provides an alternate dynamic test method for flow-rate characteristics using an isothermal tank instead of a flow meter. However, this method measures only the decreasing flow rate part of the hysteresis curve of the forward flow and relief flow characteristics.
Pneumatic fluid power — Electro-pneumatic pressure control valves — Part 2: Test methods to determine main characteristics to include in the supplier's literature
- ICS
- 23.100.50
- CCS
- 发布
- 2021-11-22
- 实施
