23.100.60 过滤器、密封垫和流体杂质 标准查询与下载
共找到 552 条与 过滤器、密封垫和流体杂质 相关的标准，共 37 页
Impact of changes in ISO fluid power particle counting－Contamination control and filter test standards
- ICS
- 23.100.60
- CCS
- 发布
- 2015-12-31
- 实施
Impact of changes in ISO fluid power particle counting－Contamination control and filter test standards
- ICS
- 23.100.60
- CCS
- 发布
- 2015-12-31
- 实施
Hydraulic fluid power－Calibration of automatic particle counters for liquids
- ICS
- 23.100.60
- CCS
- 发布
- 2015-12-31
- 实施
Hydraulic fluid power－Component cleanliness－Guidelines for achieving and controlling cleanliness of components from manufacture to installation
- ICS
- 23.100.60
- CCS
- 发布
- 2015-12-31
- 实施
Hydraulic fluid power－Assembled systems－Verification of cleanliness
- ICS
- 23.100.60
- CCS
- 发布
- 2015-12-31
- 实施
Hydraulic fluid power-Component cleanliness-Guidelines for achieving and controlling cleanliness of components from manufacture to installation
- ICS
- 23.100.60
- CCS
- 发布
- 2015-12-31
- 实施
Hydraulic fluid power－Cleanliness of parts and components－Inspection document and principles related to contaminant collection, analysis and data reporting
- ICS
- 23.100.60
- CCS
- 发布
- 2015-12-31
- 实施
Hydraulic fluid power－Cleanliness of parts and components－Inspection document and principles related to contaminant collection, analysis and data reporting
- ICS
- 23.100.60
- CCS
- 发布
- 2015-12-31
- 实施
Hydraulic fluid power -- Calibration of automatic particle counters for liquids
- ICS
- 23.100.60
- CCS
- J20
- 发布
- 2015-12-21
- 实施
Scope is not provided for this standard
Filters for compressed air -- Methods of test -- Part 4: Water
- ICS
- 23.100.60
- CCS
- 发布
- 2015-12-21
- 实施
This part of ISO 6194 describes seals utilising elastomeric sealing elements. They are considered suitable for use under low-pressure conditions (see 6.1). This part of ISO 6194 shows seal types and examples. It also specifies the nominal dimensions and tolerances of the seals, shafts and housings, as well as a dimensional identification code. NOTE ISO 6194 is complementary to ISO 16589 which covers seals incorporating thermoplastic sealing elements.
Rotary shaft lip-type seals incorporating elastomeric sealing elements -- Part 1: Nominal dimensions and tolerances
- ICS
- 23.100.60
- CCS
- 发布
- 2015-09-03
- 实施
This International Standard specifies procedures for extracting fluid samples from a hydraulic fluid power system under operation. The preferred method is to extract fluid samples from a main flowline of an operating hydraulic system in such a manner that the particulate contaminant in the sample is representative of the fluid flowing at the point of sampling. An alternative method is to extract a sample from the reservoir of an operating hydraulic system, but this method should only be used if a suitable sampler is not fitted. The samples taken are used for particulate contamination analysis.
Hydraulic fluid power -- Particulate contamination analysis -- Extraction of fluid samples from lines of an operating system
- ICS
- 23.100.60
- CCS
- 发布
- 2015-09-03
- 实施
This International Standard defines methods a) to measure the cleanliness of a fluid in an assembled hydraulic fluid power system, b) to verify a required system cleanliness upon release of the system from the production area, and c) if needed, to clean the system to the required cleanliness level. The clean-up procedure specified in this International Standard is not intended to replace proper system flushing procedures; see ISO 23309 for a system flushing procedure. Components and parts used in such systems should be clean prior to assembly; see ISO 18413 for guidance.
Hydraulic fluid power -- System clean-up procedures and verification of cleanliness of assembled systems
- ICS
- 23.100.60
- CCS
- 发布
- 2015-09-03
- 实施
This part of ISO 6194 describes seals utilizing elastomeric sealing elements. They are normally considered suitable for use only at low pressures (see ISO 6194-1:2007, 6.1). This part of ISO 6194 defines and classifies typical surface imperfections that can impair the function of the seals and is intended as a convenience for purchasers and manufacturers in their discussions concerning the importance of these imperfections in different applications. NOTE ISO 6194 (all parts) is complementary to ISO 16589 (all parts), which covers seals incorporating thermoplastic sealing elements.
Rotary-shaft lip-type seals incorporating elastomeric sealing elements -- Part 5: Identification of visual imperfections
- ICS
- 23.100.60
- CCS
- 发布
- 2015-09-03
- 实施
This International Standard specifies a procedure for evaluating differential pressure versus flow characteristics of hydraulic filters and constitutes a basis for agreement between the filter manufacturer and user. It also specifies a method for measurement of the differential pressure generated at different flow rates and viscosities by the relevant parts of a filter assembly, that is the housing, the filter element and any valves contained within the housing that are in the flow stream.
Hydraulic fluid power -- Filters -- Evaluation of differential pressure versus flow characteristics
- ICS
- 23.100.60
- CCS
- 发布
- 2015-09-03
- 实施
This International Standard specifies an automatic particle counting procedure for determining the number and sizes of particles present in hydraulic-fluid bottle samples of clear, homogeneous, single-phase liquids using an automatic particle counter (APC) that works on the light-extinction principle. This International Standard is applicable to the monitoring of a) the cleanliness level of fluids circulating in hydraulic systems, b) the progress of a flushing operation, c) the cleanliness level of support equipment and test rigs, d) the cleanliness level of packaged stock. NOTE 1 Measurements can be made with particles suspended in the original liquid or in a sample of the liquid diluted with a compatible liquid to reduce coincidence error. NOTE 2 The presence of a fluid interface obstructs the light beam and gives false signals.
Hydraulic fluid power -- Determination of the particulate contamination level of a liquid sample by automatic particle counting using the light-extinction principle
- ICS
- 23.100.60
- CCS
- 发布
- 2015-09-03
- 实施
This International Standard defines a sequence of tests for verifying filter elements. It can be used to check their hydraulic, mechanical and separation characteristics. This International Standard is not intended to qualify a filter for a particular duty or replicate conditions of service. This can only be done by a specific test protocol developed for the purpose, including actual conditions of use (e.g. the operating fluid). The procedure in this International Standard is applicable to individual fluids or types of fluids that have similar chemistry.
Hydraulic fluid power -- Sequence of tests for verifying performance characteristics of filter elements
- ICS
- 23.100.60
- CCS
- 发布
- 2015-09-03
- 实施
ISO 6194 describes seals utilizing elastomeric sealing elements. They are considered suitable for use under low-pressure conditions (see ISO 6194-1:2007, 6.1). This part of ISO 6194 specifies general test requirements for rotary shaft lip-type seals. The tests may be used for qualification purposes. NOTE ISO 6194 is complementary to ISO 16589 which covers seals incorporating thermoplastic sealing elements.
Rotary shaft lip-type seals incorporating elastomeric sealing elements -- Part 4: Performance test procedures
- ICS
- 23.100.60
- CCS
- 发布
- 2015-09-03
- 实施
ISO 16589 specifies seals utilizing sealing elements manufactured from suitably formulated compounds based on thermoplastic materials, such as polytetrafluoroethylene (PTFE). They are considered suitable for use under low pressure conditions. This part of ISO 16589 shows seal types and examples. It also specifies the nominal dimensions and tolerance of the seals, shafts and housings, as well as a dimensional identification code. NOTE ISO 16589 is complementary to ISO 6194, which covers seals incorporating elastomeric sealing elements.
Rotary shaft lip-type seals incorporating thermoplastic sealing elements -- Part 1: Nominal dimensions and tolerances
- ICS
- 23.100.60
- CCS
- 发布
- 2015-09-03
- 实施
ISO 16589 specifies seals utilizing sealing elements manufactured from suitably formulated compounds, based on thermoplastic materials, such as polytetrafluoroethylene (PTFE). They are considered suitable for use under low pressure conditions. This part of ISO 16589 gives users of lip-type seals guidance on the careful storage and handling and proper installation of rotary shaft lip-type seals; attention is drawn to the hazards involved and ways of avoiding them are pointed out. NOTE ISO 16589 is complementary to ISO 6194, which covers seals incorporating elastomeric sealing elements.
Rotary shaft lip-type seals incorporating thermoplastic sealing elements -- Part 3: Storage, handling and installation
- ICS
- 23.100.60
- CCS
- 发布
- 2015-09-03
- 实施
