25.040.10 机械加工中心 标准查询与下载

NF E60-172-2*NF ISO 10791-2:2001 多工位数控加工中心的试验条件.第2部分:带垂直主轴或带垂直旋转主轴通用头的机器的几何尺寸试验(垂直的Z轴)

Test conditions for machining centres - Part 2 : geometric tests for machines with vertical spindle or universal heads with vertical primary rotary axis (vertical Z-axis).

BS ISO 10791-9:2001 加工中心的试验条件.刀具更换和托架更换所用时间的估计

This part of ISO 10791 specifies certain standard test conditions for assessing the conventional length of the operating times spent by the machine to carry out different metal cutting functions. It considers two types of operating times, namely those taken by the functions of: — automatic tool change (see clause 5); — automatic pallet change (see clause 6). The purpose of the methods described in this part of ISO 10791 is to permit the comparison of the performance of different machining centres of similar size and features. The data obtained may also be used to establish conventional change times in technical literature in a uniform and comparable way. It is also possible to check them on a machine, both when it is new and during its working life.

Test conditions for machining centres - Evaluation of the operating times of tool change and pallet change

BS ISO 10791-2:2001 加工中心的试验条件.带垂直主轴或(垂直Z-轴)万用头的机床的几何试验

This part of ISO 10791 specifies, with reference to ISO 230-1, the geometric tests for machining centres (or numerically controlled milling machines, boring machines, etc., where applicable) with vertical spindle (that is vertical Z-axis). This part of ISO 10791 applies to machining centres having basically three numerically controlled axes, that is three linear axes (X, Y and Z) of up to 2 000 mm length, but also refers to supplementary motions, such as rotary axes (A', B' and C'), those of rams, quill, or universal heads. Motions other than those mentioned are considered as special features and the relevant tests are not included in this part of ISO 10791. This part of ISO 10791 describes geometric tests for optional horizontal spindles as well as for two possible types of universal heads in the following annexes: — annex A: optional horizontal spindles (tests AG1 to AG6); — annex B: rotary heads, with one numerically controlled rotary axis (tests BG1 and BG2); — annex C: swivel heads, with two numerically controlled rotary axes perpendicular to each other (tests CG1 to CG7). This part of ISO 10791 deals only with the verification of the accuracy of the machine. It does not apply to the testing of the machine operation, which should be checked separately. Some tests concerning the performance of the machine operating under no-load or finishing conditions are included in other parts of ISO 10791.

Test conditions for machining centres - Geometric tests for machines with vertical spindle or universal heads with vertical primary rotary axis (vertical Z-axis)

ISO 10791-8:2001 加工中心试验条件 第8部分：3个协调平面的轮廓性能的评价

This part of ISO 10791 specifies a method of checking the contouring performance of machining centres (or numerically controlled milling machines, etc., where applicable) by conducting circular tests in the three coordinate planes (XY, YZ and XZ) and by evaluating the radial deviation, F, and circular deviation, G, in accordance with ISO 230-4. NOTE Measurements of circular movements can be carried out by different methods as described in 6.6 of ISO 230-1:1996. These methods consist of using a rotating one-dimensional probe and a test mandrel, a circular masterpiece and a two-dimensional probe, or a telescoping ball bar. Other test methods may be applied if the accuracy of the equipment is the same as (or better than) the accuracy of the methods described. Influences of typical machine deviations on circular paths are shown in annex B of ISO 230-4:1996. The purpose of the checks by circular tests described in this part of ISO 10791 is to verify the circular movement — only in one position per coordinate plane of the machine, — at only one feed rate, and — to repeat the test once in the opposite contouring direction. The purpose of this part of ISO 10791 is not to provide a means of analysing the causes for the measured circular deviations, but to offer the user a method for periodic checking of the machine tool. It is recommended to carry out the tests of this part of ISO 10791 once the machine tool has satisfactorily undergone the acceptance tests and to use these results as a basis for comparison when carrying out periodic checks. Therefore, acceptable deviations from the initial results shall be decided by the user. If the tests are used for machine acceptance purposes, the supplier/manufacturer and the user shall agree oh specific diameters, feed rates and tolerances for the tests. NOTE ISO 10791-6, which deals with the accuracy of feeds, speeds and interpolations, also includes as test K4 a circular test. Here, the purpose is to check the mutual behaviour of two linear axes (generally X and Y) at two defined feed rates for one defined diameter. This is more or less a diagnostic test with respect to the circular interpolation, whereas the circular tests of this part of ISO 10791 give information on the overall contouring performance of the machine.

Test conditions for machining centres - Part 8: Evaluation of the contouring performance in the three coordinate planes

ISO 10791-2:2001 加工中心试验条件 第2部分：立式或带有垂直主回转轴万能轴头的机床的几何精度试验（垂直轴 Z）

This part of ISO 10791 specifies, with reference to ISO 230-1, the geometric tests for machining centres (or numerically controlled milling machines, boring machines, etc., where applicable) with vertical spindle (that is vertical Z-axis). This part of ISO 10791 applies to machining centres having basically three numerically controlled axes, that is three linear axes (X, Y and Z) of up to 2 000 mm length, but also refers to supplementary motions, such as rotary axes (A', B' and C'), those of rams, quill, or universal heads. Motions other than those mentioned are considered as special features and the relevant tests are not included in this part of ISO 10791. This part of ISO 10791 describes geometric tests for optional horizontal spindles as well as for two possible types of universal heads in the following annexes: — annex A: optional horizontal spindles (tests AG1 to AG6); — annex B: rotary heads, with one numerically controlled rotary axis (tests BG1 and BG2); — annex C: swivel heads, with two numerically controlled rotary axes perpendicular to each other (tests CG1 to CG7). This part of ISO 10791 deals only with the verification of the accuracy of the machine. It does not apply to the testing of the machine operation, which should be checked separately. Some tests concerning the performance of the machine operating under no-load or finishing conditions are included in other parts of ISO 10791.

Test conditions for machining centres - Part 2: Geometric tests for machines with vertical spindle or universal heads with vertical primary rotary axis (vertical Z-axis)

ISO 10791-9:2001 加工中心检验条件 第9部分：刀具交换和托板交换操作时间的评价

GB/T 18400的本部分规定了加工中心(以下简称机床)在确立的标准检验条件下，执行不同金属 切削功能时所需常规操作时间的评定方法。 本部分适用于下列两种功能操作时间的评定： ——刀具自动交换(见第5章)； ——托板自动交换(见第6章)。 GB／T 18400的本部分所述方法适用于规格和特征相似的不同机床之间性能的比较。 用统一和比较方式所获得的数据也适用于技术报告中常规交换时间的确立，以及对新机床和处于 寿命期间的机床进行检验。

Test conditons for machining centres - Part 9: Evaluation of the operating times of tool change and pallet change

DIN ISO 10791-7:2001 机床.加工中心的试验条件.第7部分:精加工试件的精度(ISO 10791-7:1998)

Machine tools - Test conditions for machining centres - Part 7: Accuracy of a finished test piece (ISO 10791-7:1998)

DIN ISO 10791-3:2001 机床.加工中心的试验条件.第3部分:分度或连续的万能主轴头机床的几何精度试验(垂直Z轴)(ISO 10791-3:1998)

The document specifies with reference to ISO 230-1 different geometric tests for machining centres with integral indexable or continuous universal heads (vertical Z-axis) and is applicable for machining centres having basically four numerically controlled axes.

Machine tools - Test conditions of machining centres - Part 3: Geometric tests for machines with integral indexable or continuous universal heads (vertical Z-axis) (ISO 10791-3:1998)

DIN ISO 10791-4:2001 机床.加工中心的检验条件.第4部分:线性和回转轴线的定位精度和重复定位精度(ISO 10791-4:1998)

The document specifies, with reference to ISO 230-2, the tolerances which apply to the positioning tests for linear axes, up to 2000 mm in length and rotary axes of machining centres.#,,#

Machine tools - Test conditions for machining centres - Part 4: Accuracy and repeatability of positioning of linear and rotary axes (ISO 10791-4:1998)

DIN ISO 10791-1:2001 机床.加工中心的检验条件.第1部分:卧式和带附加主轴头几何精度检验(水平Z轴)(ISO 10791-1:1999)

Machine tools - Test conditions for machining centres - Part 1: Geometric tests for machines with horizontal spindle and with accessory heads (horizontal Z-axis) ( ISO 10791-1:1999)

JIS B 6336-5:2000 多工序自动数字控制机床（加工中心）的试验条件.第5部分:工件固托板定位的精确度和可重复性

この規格は，JIS B 6191及びJIS B 6192に基づいて，一台のマシニングセンタで使用する個々のパレットの位置決めの繰返し性及びパレット相互の位置決めの正確さの評価方法について規定する。

Test conditions for machining centers -- Part 5: Accuracy and repeatability of positioning of work-holding pallets

JIS B 6336-7:2000 多工序自动数字控制机床（加工中心）的试验条件.第7部分:精加工试件的精确度

この規格は，JIS B 6191に基づいて，標準の工作物を用いて仕上げ条件下で行う工作精度検査，すなわち，仕上げられた工作物の幾何学的精度の検査事項について規定する。

Test conditions for machining centers -- Part 7: Accuracy of a finished test piece

JIS B 6336-6:2000 多工序自动数字控制机床（加工中心）的试验条件.第6部分:进刀、速度和内插补的精确度

この規格は，JIS B 6191及びJIS B 619に基づいて，マシニングセンタの運動学的精度の検査条件，すなわち，主軸速度，個々の数値制御軸の直進送り速度及び二つ以上の数値制御による直進軸及び/又は回転軸（4.参照)の同時制御によって描かれた軌跡の精度の検査条件に規定する。

Test conditions for machining centers -- Part 6: Accuracy of feeds, speeds and interpolations

JIS B 6336-1:2000 多工序自动数字控制机床（加工中心机床）的试验条件.第1部分:有水平轴和附属头的机床的几何试验(水平Z轴)

この規格は，JIS B 6191に基づいて，横形(けなわち，水平Z軸)マシニングセンタ(又は数値制御フライス盤，数値制御中ぐり盤などの適用できるもの)の静的精度の検査条件について規定する。

Test conditions for machining centers -- Part 1: Geometric tests for machines with horizontal spindle and with accessory heads (horizontal Z-axis)

JIS B 6336-3:2000 多工序自动数字控制机床（加工中心）的试验条件.第3部分:带总组合工位转台或连续通用头的机床的几何试验

この規格は，J13 B 6191に基づいて，固定又は連続割出万能主軸頭(垂直Z軸)をもつマシニングセンタ(又は数値制御フライス盤，数値制御中ぐり盤などの適用できるもの)の静的精度の検査条件について規定する。

Test conditions for machining centers -- Part 3: Geometric tests for machines with integral indexable or continuous universal heads (vertical Z-axis)

JIS B 6336-4:2000 多工序自动数字控制机床（加工中心）的试验条件.第4部分:线性和旋转轴定位的精确度和可重复性

この規格は，JIS B 6192に基づいて，マシニングセンタの長さ2 000 mm以下の直進運動軸及び回転運動軸の位置決め精度検査に適用する許容値について規定する。

Test conditions for machining centers -- Part 4: Accuracy and repeatability of positioning of linear and rotary axes

ISO 10791-3:1998/cor 1:1999 加工中心检验条件 第3部分:分度或连续的万能主轴头机床的几何精度检验(垂直Z轴) 技术勘误1

This is Technical Corrigendum 1 to ISO 10791-3-1998 (Test conditions for machining centres — Part 3: Geometric tests for machines with integral indexable or continuous universal heads (vertical Z-axis))

Test conditions of machining centres - Part 3: Geometric tests for machines with integral indexable or continuous universal heads (vertical Z-axis); Technical Corrigendum 1

BS ISO 10791-3:1999 加工中心检验条件.第3部分:分度或连续的万能主轴头机床的几何精度检验(垂直Z轴)

This part of ISO 10791 specifies, with reference to ISO 230-1, the geometric tests for machining centres (or numerically controlled milling machines, boring machines, etc., where applicable) with integral indexable or continuous universal heads (vertical Z-axis). This part of ISO 10791 applies to machining centres having basically six numerically controlled axes, of which three are linear (X, Y and Z) up to 2 000 mm in length, and three are rotary (A or D and B on the head, and C' on the table). Movements other than those mentioned are considered as special features and the relevant tests are not included in this part of ISO 10791. This part of ISO 10791 describes geometric tests for three possible types of accessory universal heads, in the annexes: — annex A: Integral universal 45°split indexable heads (B and D axes), with mechanical indexing of the different angular positions of the two bodies (e.g. Hirth couplings): the relevant tests (AG1 to AG9) check only the resulting position of the spindle; — annex B: Integral universal swivel heads (B and A axes), with two numerically controlled rotary axes perpendicular to each other (tests BG1 to BG7); — annex C: Integral universal 45°split continuous heads (B and D axes), similar to the first type but provided with continuous positioning of the two numerically controlled rotary axes: the relevant tests (CG1 to CG7) check all the geometric features (planes and axes) which contribute to the resulting position of the spindle, excluding the positioning accuracy of the two rotary axes; these tests can also be used for a deeper investigation on the 45°indexable heads, if their movements and locks allow this. This part of ISO 10791 deals only with the verification of accuracy of the machine and does not apply to the testing of the machine operation, which should generally be checked separately. Certain tests concerning the performance of the machine operating under no-load or finishing conditions are included in other parts of ISO 10791.

Test conditions for machining centres - Geometric tests for machines with integral indexable or continuous universal heads (vertical Z-axis)

NF E60-172-1:1999 多工序数控加工中心的试验条件.第1部分:带水平主轴和辅助头的机床的几何尺寸试验(水平的Z轴)

Test conditions of machining centres. Part 1 : geometric tests for machines with horizontal spindle and with accessory heads (horizontal Z axis).

ISO 10791-3:1998 加工中心检验条件 第3部分:分度或连续的万能主轴头机床的几何精度检验(垂直Z轴)

This part of ISO 10791 specifies, with reference to ISO 230-1, the geometric tests for machining centres (or numerically controlled milling machines, boring machines, etc., where applicable) with integral indexable or continuous universal heads (vertical Z-axis). This part of ISO 10791 applies to machining centres having basically six numerically controlled axes, of which three are linear (X, Y and Z) up to 2 000 mm in length, and three are rotary (A or D and B on the head, and C' on the table). Movements other than those mentioned are considered as special features and the relevant tests are not included in this part of ISO 10791. This part of ISO 10791 describes geometric tests for three possible types of accessory universal heads, in the annexes: — annex A: Integral universal 45°split indexable heads (B and D axes), with mechanical indexing of the different angular positions of the two bodies (e.g. Hirth couplings): the relevant tests (AG1 to AG9) check only the resulting position of the spindle; — annex B: Integral universal swivel heads (B and A axes), with two numerically controlled rotary axes perpendicular to each other (tests BG1 to BG7); — annex C: Integral universal 45°split continuous heads (B and D axes), similar to the first type but provided with continuous positioning of the two numerically controlled rotary axes: the relevant tests (CG1 to CG7) check all the geometric features (planes and axes) which contribute to the resulting position of the spindle, excluding the positioning accuracy of the two rotary axes; these tests can also be used for a deeper investigation on the 45°indexable heads, if their movements and locks allow this. This part of ISO 10791 deals only with the verification of accuracy of the machine and does not apply to the testing of the machine operation, which should generally be checked separately. Certain tests concerning the performance of the machine operating under no-load or finishing conditions are included in other parts of ISO 10791.

Test conditions of machining centres - Part 3: Geometric tests for machines with integral indexable or continuous universal heads (vertical Z-axis)